Technician tool v0.6

Imported from the Google Drive folder 004-technician_tool/v0.6.

docs/firmware-diagnostics-proposals.md

@@ -0,0 +1,90 @@
+# Firmware diagnostics improvement proposals
+
+> **Status: draft proposal, AI-generated (Claude) for review by the firmware team.**
+> Nothing here is implemented. The firmware source was only read for analysis;
+> no firmware was changed. Every item links to an observation from bench
+> testing box `A4:CB:8F:C9:46:F8` (firmware v1.0, build `45fa9d5b9`) or from the
+> sample logs, so the value of each change can be judged.
+
+## Why
+
+Troubleshooting currently depends on reverse-engineering free-text log lines and
+on a status LED whose states overlap. Observed problems:
+
+| # | Observation | Effect for technicians |
+|---|---|---|
+| O1 | A new, uncommissioned box shows **green** for about 60 s, then purple | Looks healthy during installation |
+| O2 | Three different states share **white** (SD error, factory reset, setup portal) | Needs serial or guesswork |
+| O3 | **Blue** means "RTC did not answer", but the RTC is just the first I2C device | A loose I2C cable is misreported as an RTC fault |
+| O4 | Every build reports `App version: 1.0` | Builds are told apart only by ELF SHA |
+| O5 | Restarts after 150 s in an error state happen **without any log line** | A self-restart looks like a crash |
+| O6 | With the RTC not running and no Internet, sensor tasks **loop forever** on `RTC is uninitialized` | An offline box records nothing, and it isn't obvious why |
+| O7 | The OTA token is printed in plain text (`OTA token loaded from NVS: %s`, `received token: %s`) | Secrets end up in technician logs |
+| O8 | Native USB loses output while no host is reading; a stale FIFO fragment is glued to the next line | The early boot after a power cycle is lost, and lines get corrupted |
+| O9 | The microphone reports "shutdown state" (GPIO3) with no hint of the cause | A technician can't tell a switch from a fault |
+| O10 | The deployed build logs some messages under different tags than the source (e.g. SD mount under `INFLUX_BUFFER`) | Parsers must ignore tags |
+
+## Serial output
+
+Priority: **P1** = large gain for little effort, **P2** = valuable, **P3** = nice to have.
+
+### P1
+
+1. **One structured boot line** with a fixed prefix, printed right after `app_init`:
+   ```
+   KOTA: boot fw=1.0.15 build=45fa9d5b hw=2 mac=A4CB8FC946F8 reset=USB_UART_CHIP_RESET mode=matter commissioned=0 last_restart=status_watchdog
+   ```
+   The tool can then identify firmware, hardware and mode from a single line (fixes O4 and O10). Fill `PROJECT_VER` from `FIRMWARE_VERSION` (currently `15` in `pinout.hpp`) so every build has a unique version.
+2. **Log every status change** inside `Status::set_status()`, with a reason argument:
+   ```
+   KOTA: status OK -> CONNECTION_ERROR reason=influx_flush_failed
+   ```
+   This is the exact LED colour. Today the tool has to infer it from about 15 different messages.
+3. **Log the reason before every `esp_restart()`** and store it (RTC memory or NVS) so it can be printed at the next boot as `last_restart=`. Values: `status_watchdog_150s`, `out_of_resources_30s`, `button_factory_reset`, `setup_portal_toggle`, `ota_done`, `init_failed:<step>` (fixes O5).
+4. **Stop printing secrets**: print only the first and last 4 characters of the OTA token, or `token=present` (fixes O7).
+5. **Warn once and continue when the time is unset**, instead of the `while (now == 946684800)` loops in `device_status.cpp` and the sensors. Record data with a `time_valid=false` field or buffer it with uptime, then correct it after SNTP (fixes O6). This is a behaviour change, but the biggest data-loss risk found.
+
+### P2
+
+6. **I2C bus scan at boot**, before any sensor init:
+   ```
+   KOTA: i2c SDA=1 SCL=1 0x39=AS7341 0x68=DS1307 0x6B=SEN66(missing) 0x76=BME688
+   ```
+   Reading the SDA/SCL levels first detects a stuck-low bus (shorted or broken cable). The scan then separates "whole cable" from "one sensor" (fixes O3).
+7. **RTC detail**: at init, print the DS1307 clock-halt (CH) bit and the raw time (`KOTA: rtc running=0 time=2000-01-01 (coin cell?)`). After SNTP sets the time, re-read it 2 s later to verify it's ticking.
+8. **SD card detail**: card type, size, FAT type, free space, which `ENV.TXT` keys are present (names only, never values) and the buffer size in lines. Example: `KOTA: sd type=SDHC size=7.4GB fs=FAT32 free=7.3GB env_keys=INFLUX_URL,INFLUX_TOKEN buffer_lines=42`.
+9. **Periodic health line** every 60 s. `DeviceStatus` already computes almost everything:
+   ```
+   KOTA: health up=312s status=CONNECTION_ERROR wifi=disconnected rssi=0 time_valid=0 sd=ok buffer=42 heap=81234 psram=6.1M last_upload=never ota=unregistered
+   ```
+10. **Matter commissioning status at boot**: `KOTA: matter fabrics=0 window=open` plus the QR payload and manual code, so the tool can show the QR code on screen when the sticker is missing.
+11. **Microphone enable reason**: `KOTA: mic enabled=0 (GPIO3=1, expected 0)` once at boot, instead of a warning every 10 s (fixes O9).
+12. **Stable error IDs** in messages, e.g. `[E-SD-01] Failed to initialize the card`, documented in one table shared by the firmware, the technician tool and the service docs.
+
+### P3
+
+13. **Console commands** over USB (the firmware already runs a `console` task): `diag` (full health dump), `i2cscan`, `sdinfo`, `ledtest` (cycles all colours so the technician can confirm the LED hardware), `version`, `bootlog`. The tool could then run checks without a reboot.
+14. **Boot-log ring buffer** in RAM, dumped with `bootlog` or on first host connect. This recovers the early boot lost on native USB after a power-switch cycle (fixes O8).
+15. **Button events**: log the press start and release with duration (`KOTA: button press 1.2s -> setup_portal`). This allows a safe button test and shows accidental factory resets.
+
+## RGB LED
+
+1. **Separate "not connected yet" from "OK"** (fixes O1): **cyan breathing** while the box is uncommissioned / advertising over BLE, fast cyan while a phone is connected, and a green flash when commissioning completes.
+2. **Split the white states** with patterns (fixes O2):
+   - SD card / `ENV.TXT` error: white, fast blink (2 Hz)
+   - factory reset in progress: white, solid
+   - Wi-Fi setup portal: white, slow breathing
+3. **Blink codes for red and blue** (fixes O3): N short pulses followed by a pause identify the part.
+   - Red: 1 = BME688, 2 = SEN66, 3 = AS7341, 4 = microphone, 5 = flicker, 6 = self-check failed
+   - Blue: 1 = RTC not responding, 2 = I2C bus stuck low
+4. **Split purple**: solid = no network/DNS; blinking = Internet works but the server rejected the box (InfluxDB 401/404, OTA 401). These need different fixes (network vs SD card settings).
+5. **Show the cause before a self-restart**: flash the error colour 3 times before `esp_restart()`. After boot, show the previous boot's error colour for 3 s (from RTC memory), so a reboot loop has a visible cause.
+6. **Update progress**: yellow blinking while downloading (faster as progress grows); orange stays solid for the self-check.
+7. **Brightness and distinguishability**: colours are set at 10 % (`255/10`). Yellow and orange, and white and cyan, are hard to tell apart in daylight. Prefer fewer colours plus patterns, and raise brightness for error states.
+8. **Heartbeat LED (GPIO6)**: keep 1 Hz for "running", add a double-blink when offline, so the heartbeat alone gives a rough state even when the RGB LED is faulty.
+
+## What changes in the technician tool
+
+- The structured `KOTA:` lines (items 1, 2, 3, 9) would replace most regex rules in `rules.toml` and make the LED model exact rather than inferred.
+- The console commands (item 13) would let guided checks test hardware directly (I2C scan, LED test) instead of asking the technician to power-cycle.
+- The new LED patterns would add answers to the Quick check (e.g. "white, blinking fast") and remove the follow-up questions currently needed to separate the white states.

docs/mac_agent_command.txt

@@ -0,0 +1,30 @@
+You are testing the KOTA sensorbox technician tool v0.5 on macOS. The current folder is
+004-technician_tool/v0.5 (a Python/PySide6 desktop app; it has only been tested on Windows so far).
+
+Rules:
+- Python only via uv or conda/mamba. Never use bare/system python or pip.
+- Do not build, modify or flash firmware other than the bundled firmware/new_system.bin.
+- Do not push anything to Git or GitLab. This is a local demo.
+- Ask me before any destructive action: formatting an SD card, Full-mode flashing, or deleting files.
+  Before formatting, show me the exact disk (identifier, name, size, current files).
+- Do not change code without telling me. Report bugs with evidence (commands and output).
+
+Tests, in order. Report pass/fail with evidence for each:
+1. Launch: `bash run_macos.command` (it offers to install uv). The app window opens; note any warnings.
+2. Tests: `UV_PROJECT_ENVIRONMENT="$HOME/Library/Caches/KotaTechnicianTool/venv-0.5" uv run --frozen pytest -q`
+3. Serial: plug in the sensorbox (native USB). The port list shows a /dev/cu.usbmodem* "Sensorbox (native USB)"
+   entry with a MAC. Connect, press "Reset & capture": the boot log starts at "ESP-ROM:esp32s3" and the
+   Diagnosis panel identifies firmware v1.0 (build 45fa9d5b9). Check whether the port disappears after the
+   reset and whether the tool reconnects.
+4. Guided troubleshooting: run "Quick check" and answer truthfully with what I tell you the LED shows.
+5. Flash (App only, factory image; the box already runs it): the tool must enter flashing mode by itself,
+   write, restart the box and report "Success ... build 45fa9d5b9". Capture the esptool output.
+6. SD card tab: the settings load from ../../002-SD_card_format/ENV.txt. The card reader and card are listed
+   (internal disks must NOT be listed). Run "Check card", then, after my OK, "Format card and write ENV.TXT".
+   It must use `diskutil eraseDisk FAT32 KOTA MBRFormat` on the correct disk, write ENV.TXT byte-identical
+   to the template, and eject the card.
+7. "Service report..." opens the browser at https://service.kota-app.com/<MAC>#kota-report=... (it is fine
+   if the page itself cannot prefill yet).
+
+At the end, write a short report: macOS version, Mac model/architecture, each test with result, errors, and
+suggested fixes (file:line).

environment.yml

@@ -7,4 +7,6 @@ dependencies:
   - python=3.12
   - pyserial>=3.5
   - pyside6>=6.7
+  - esptool>=4.8,<5
+  - segno>=1.6
   - pytest>=8

kota_tech/__init__.py

@@ -1,3 +1,3 @@
 """KOTA sensorbox technician tool."""
 
-__version__ = "0.2.0"
+__version__ = "0.6.0"

kota_tech/diag/engine.py

@@ -25,6 +25,7 @@ from ..core.logline import LineKind, LogLine
 from .firmware import FirmwareInfo
 
 RULES_PATH = Path(__file__).with_name("rules.toml")
+_MAC_LINE = re.compile(r"Device MAC address: ([0-9A-Fa-f]{2}(?::[0-9A-Fa-f]{2}){5})")
 
 
 class Severity(IntEnum):
@@ -59,6 +60,7 @@ MILESTONES = [
     ("sd_mounted", "SD card mounted", False),
     ("env_loaded", "ENV.TXT read (InfluxDB settings)", False),
     ("matter_started", "Matter started", True),
+    ("matter_commissioned", "Paired in Matter", True),
     ("local_wifi_mode", "Local Wi-Fi mode (SSID from SD card)", True),
     ("sensors_ready", "All sensors started", False),
     ("wifi_connected", "Connected to Wi-Fi", False),
@@ -215,6 +217,7 @@ class Report:
     boots: list[BootRecord]
     lines: int
     mid_run: bool                         # no boot seen yet
+    technician: list[str] = field(default_factory=list)   # guided-check answers
 
     def to_text(self) -> str:
         out = [f"VERDICT: {self.verdict}",
@@ -243,6 +246,10 @@ class Report:
             out.append("Resolved during this session:")
             for f in self.resolved:
                 out.append(f"  - {f.title}" + (f" (by: {f.resolved_by})" if f.resolved_by else ""))
+        if self.technician:
+            out.append("")
+            out.append("Technician checks:")
+            out += [f"  - {t}" for t in self.technician]
         return "\n".join(out)
 
 
@@ -271,6 +278,9 @@ class DiagnosticsEngine:
         self.lines = 0
         self._tool_reset_at: float | None = None
         self._panic_tail = 0     # RAW lines after a panic line to keep
+        self.technician: list[str] = []
+        self.mac: str | None = None      # from "ID: Device MAC address: ..." at boot
+        self.matter_advert: str | None = None   # "Advertise commission parameter vendorID=..." line
 
     @property
     def boot(self) -> BootRecord:
@@ -310,6 +320,10 @@ class DiagnosticsEngine:
             self._crash_finding().evidence.append(text)
 
         self.firmware.observe(text)
+        if m := _MAC_LINE.search(text):
+            self.mac = m.group(1).upper()
+        if "Advertise commission parameter" in text:
+            self.matter_advert = text
         matched = False
         for rule in self.rules:
             m = rule.pattern.search(text)
@@ -369,7 +383,22 @@ class DiagnosticsEngine:
         # Reached milestones in the order they happened, then the pending ones.
         ms.sort(key=lambda m: (m[2] is None, m[2] or 0))
         return Report(verdict, vsev, self.led, self.led_reason, self.firmware, ms, roots,
-                      earlier, resolved, list(self.boots), self.lines, mid_run)
+                      earlier, resolved, list(self.boots), self.lines, mid_run, list(self.technician))
+
+    def add_confirmed(self, key: str, severity: Severity, title: str, meaning: str,
+                      actions: tuple[str, ...]) -> Finding:
+        """A finding established by a guided check (technician answer + log)."""
+        f = self.findings.get(key)
+        if f is None:
+            f = self.findings[key] = Finding(key, key, severity, title, meaning, tuple(actions))
+        f.count += 1
+        f.boot = self.boot.index
+        f.resolved = False
+        f.evidence.append("confirmed by the technician during a guided check")
+        return f
+
+    def note_technician(self, text: str) -> None:
+        self.technician.append(text)
 
     # ------------------------------------------------------------ internals
     def _new_boot(self, host_time: float, explicit: bool) -> None:

kota_tech/diag/firmware.py

@@ -26,6 +26,12 @@ KNOWN: dict[str, KnownFirmware] = {
         sd_wifi=False,
         setup_portal=False,
     ),
+    "c94ba0e9b": KnownFirmware(
+        name="v1.0 source build (Sep 26 2026)",
+        source="developer build, built by Krzysztof Kallas",
+        sd_wifi=True,
+        setup_portal=True,
+    ),
 }
 
 _ELF = re.compile(r"app_init: ELF file SHA256:\s+(?P<sha>[0-9a-f]{6,})")

kota_tech/diag/guides.py

@@ -0,0 +1,401 @@
+"""Guided troubleshooting: executes the decision trees in guides.toml.
+
+GUI-independent. The runner is fed the same LogLines as the diagnostics
+engine, reads the engine's report to route and to skip questions the log
+already answers, asks the host to perform tool actions (board reset), and
+records every answer and conclusion in the engine so they appear in the
+report and the session log.
+"""
+
+from __future__ import annotations
+
+import re
+import time
+import tomllib
+from collections.abc import Callable
+from dataclasses import dataclass, field
+from pathlib import Path
+
+from ..core.logline import LogLine
+from .engine import LED, DiagnosticsEngine, Severity
+
+GUIDES_PATH = Path(__file__).with_name("guides.toml")
+# LED answers a technician can give (engine colours + a reboot-loop pattern).
+LED_ANSWERS = ["GREEN", "PURPLE", "RED", "BLUE", "WHITE", "YELLOW", "ORANGE", "OFF", "CYCLING"]
+LED_ANSWER_LABELS = {**{k: v[0] for k, v in LED.items()},
+                     "CYCLING": "Keeps changing / goes dark every few seconds"}
+STEP_TYPES = {"led", "question", "info", "wait", "route"}
+END_SEVERITY = {"ok": None, "info": Severity.INFO, "warning": Severity.WARNING,
+                "error": Severity.ERROR, "critical": Severity.CRITICAL}
+
+
+@dataclass(frozen=True)
+class Option:
+    label: str
+    next: str
+
+
+@dataclass(frozen=True)
+class Step:
+    id: str
+    type: str
+    text: str = ""
+    options: tuple[Option, ...] = ()
+    route: dict[str, str] = field(default_factory=dict)      # led colour -> target
+    routes: dict[str, str] = field(default_factory=dict)     # rule id -> target
+    default: str | None = None
+    next: str | None = None
+    tool_action: str | None = None
+    until: re.Pattern[str] | None = None
+    until_milestone: str | None = None
+    fail_on: re.Pattern[str] | None = None
+    timeout_s: float = 60.0
+    pass_on_timeout: bool = False
+    on_ok: str | None = None
+    on_fail: str | None = None
+    on_timeout: str | None = None
+    skip_if_finding: str | None = None
+    skip_unless_feature: str | None = None
+    skip_to: str | None = None
+    show_qr: bool = False              # show the Matter pairing QR next to the step text
+
+    def targets(self) -> list[str]:
+        t = [o.next for o in self.options] + list(self.route.values()) + list(self.routes.values())
+        t += [x for x in (self.default, self.next, self.on_ok, self.on_fail, self.on_timeout, self.skip_to) if x]
+        return t
+
+
+@dataclass(frozen=True)
+class End:
+    id: str
+    severity: str
+    title: str
+    text: str
+    actions: tuple[str, ...] = ()
+
+
+@dataclass(frozen=True)
+class Guide:
+    id: str
+    title: str
+    summary: str
+    recommend: tuple[str, ...]
+    start: str
+    steps: dict[str, Step]
+    ends: dict[str, End]
+
+
+def load_guides(path: Path = GUIDES_PATH) -> dict[str, Guide]:
+    data = tomllib.loads(path.read_text(encoding="utf-8"))
+    guides: dict[str, Guide] = {}
+    for g in data["guide"]:
+        steps = {}
+        for s in g.get("step", []):
+            steps[s["id"]] = Step(
+                id=s["id"], type=s["type"], text=s.get("text", ""),
+                options=tuple(Option(o["label"], o["next"]) for o in s.get("options", ())),
+                route=dict(s.get("route", {})), routes=dict(s.get("routes", {})),
+                default=s.get("default"), next=s.get("next"), tool_action=s.get("tool_action"),
+                until=re.compile(s["until"]) if "until" in s else None,
+                until_milestone=s.get("until_milestone"),
+                fail_on=re.compile(s["fail_on"]) if "fail_on" in s else None,
+                timeout_s=float(s.get("timeout_s", 60)), pass_on_timeout=bool(s.get("pass_on_timeout", False)),
+                on_ok=s.get("on_ok"), on_fail=s.get("on_fail"), on_timeout=s.get("on_timeout"),
+                skip_if_finding=s.get("skip_if_finding"), skip_unless_feature=s.get("skip_unless_feature"),
+                skip_to=s.get("skip_to"), show_qr=bool(s.get("show_qr", False)),
+            )
+        ends = {e["id"]: End(e["id"], e["severity"], e["title"], e["text"], tuple(e.get("actions", ())))
+                for e in g.get("end", [])}
+        guides[g["id"]] = Guide(g["id"], g["title"], g["summary"], tuple(g.get("recommend", ())),
+                                g["start"], steps, ends)
+    _validate(guides)
+    return guides
+
+
+def _validate(guides: dict[str, Guide]) -> None:
+    for g in guides.values():
+        if g.start not in g.steps:
+            raise ValueError(f"guide {g.id}: start step {g.start!r} missing")
+        for s in g.steps.values():
+            if s.type not in STEP_TYPES:
+                raise ValueError(f"{g.id}.{s.id}: unknown step type {s.type!r}")
+            if s.type == "led" and set(s.route) - set(LED_ANSWERS):
+                raise ValueError(f"{g.id}.{s.id}: unknown LED colours {set(s.route) - set(LED_ANSWERS)}")
+            if s.type == "wait" and not (s.until or s.until_milestone or s.pass_on_timeout):
+                raise ValueError(f"{g.id}.{s.id}: wait step needs until/until_milestone/pass_on_timeout")
+            if s.tool_action not in (None, "reset"):
+                raise ValueError(f"{g.id}.{s.id}: unknown tool_action {s.tool_action!r}")
+            for t in s.targets():
+                kind, _, ref = t.partition(":")
+                if kind == "end" and ref not in g.ends:
+                    raise ValueError(f"{g.id}.{s.id}: unknown end {ref!r}")
+                elif kind == "guide" and ref not in guides:
+                    raise ValueError(f"{g.id}.{s.id}: unknown guide {ref!r}")
+                elif not ref and t not in g.steps:
+                    raise ValueError(f"{g.id}.{s.id}: unknown step {t!r}")
+        for e in g.ends.values():
+            if e.severity not in END_SEVERITY:
+                raise ValueError(f"{g.id}.end.{e.id}: unknown severity {e.severity!r}")
+
+
+def recommended(guides: dict[str, Guide], engine: DiagnosticsEngine) -> list[Guide]:
+    """Guides matching the current root findings (in root order), then the LED."""
+    report = engine.report()
+    keys: list[str] = []
+    for rc in report.roots:
+        keys.append(rc.finding.rule_id)
+        keys += [c.rule_id for c in rc.consequences]
+    if report.led not in ("UNKNOWN",):
+        keys.append(f"led:{report.led}")
+    out: list[Guide] = [g for g in guides.values() if "always" in g.recommend]
+    for k in keys:
+        for g in guides.values():
+            if k in g.recommend and g not in out:
+                out.append(g)
+    return out
+
+
+@dataclass
+class View:
+    """What the UI should show right now."""
+    guide: Guide | None = None
+    step: Step | None = None
+    text: str = ""
+    options: list[tuple[str, str]] = field(default_factory=list)   # (key, label)
+    waiting: bool = False
+    remaining_s: float = 0.0
+    note: str = ""
+    end: End | None = None
+    can_back: bool = False
+
+
+class GuideRunner:
+    def __init__(self, engine: DiagnosticsEngine, guides: dict[str, Guide] | None = None,
+                 on_action: Callable[[str], bool] | None = None,
+                 on_log: Callable[[str], None] | None = None,
+                 clock: Callable[[], float] = time.monotonic):
+        self.engine = engine
+        self.guides = guides if guides is not None else load_guides()
+        self._on_action = on_action or (lambda _a: False)
+        self._on_log = on_log or (lambda _t: None)
+        self._clock = clock
+        self.cancel()
+
+    # ------------------------------------------------------------ control
+    def cancel(self) -> None:
+        self.guide: Guide | None = None
+        self.step: Step | None = None
+        self.end: End | None = None
+        self.note = ""
+        self._stack: list[tuple[str, str]] = []   # (guide id, step id) for Back
+        self._wait_started = 0.0
+        self._wait_boot = 0
+        self._wait_milestones: set[str] = set()
+
+    def start(self, guide_id: str) -> None:
+        self.cancel()
+        self._enter_guide(guide_id)
+
+    def answer(self, key: str) -> None:
+        """Pick an option: LED colour name for led steps, option index otherwise."""
+        s = self.step
+        if s is None:
+            return
+        if s.type == "led":
+            label = LED_ANSWER_LABELS.get(key, key)
+            self._record(s, label)
+            self._check_led(key)
+            target = s.route.get(key)
+        elif s.type == "question":
+            opt = s.options[int(key)]
+            self._record(s, opt.label)
+            target = opt.next
+        else:
+            return
+        if target:
+            self._push()
+            self._go(target)
+
+    def proceed(self) -> None:
+        """Continue on info steps; 'skip waiting' on wait steps."""
+        s = self.step
+        if s is None:
+            return
+        if s.type == "info" and s.next:
+            self._push()
+            self._go(s.next)
+        elif s.type == "wait":
+            self._record(s, "technician skipped the wait")
+            self._finish_wait("timeout")
+
+    def back(self) -> None:
+        # Never step back into a wait: re-entering it could restart the box.
+        while self._stack:
+            gid, sid = self._stack.pop()
+            if self.guides[gid].steps[sid].type != "wait":
+                self.guide, self.end, self.note = self.guides[gid], None, ""
+                self._enter_step(sid)
+                return
+
+    # --------------------------------------------------------------- feed
+    def feed(self, line: LogLine) -> None:
+        s = self.step
+        if s is None or s.type != "wait":
+            return
+        if s.fail_on and s.fail_on.search(line.text):
+            self._record(s, f"log: {line.text}")
+            self._finish_wait("fail")
+        elif s.until and s.until.search(line.text):
+            self._record(s, f"log: {line.text}")
+            self._finish_wait("ok")
+        elif s.until_milestone and self._milestone_new(s.until_milestone):
+            self._record(s, f"milestone reached: {s.until_milestone}")
+            self._finish_wait("ok")
+
+    def tick(self) -> None:
+        s = self.step
+        if s is not None and s.type == "wait" and self._clock() - self._wait_started >= s.timeout_s:
+            self._finish_wait("ok" if s.pass_on_timeout else "timeout")
+
+    # --------------------------------------------------------------- view
+    def view(self) -> View:
+        v = View(guide=self.guide, step=self.step, end=self.end, note=self.note, can_back=bool(self._stack))
+        s = self.step
+        if s is None:
+            return v
+        v.text = self._render(s.text)
+        if s.type == "led":
+            v.options = [(k, LED_ANSWER_LABELS[k]) for k in LED_ANSWERS if k in s.route]
+        elif s.type == "question":
+            v.options = [(str(i), o.label) for i, o in enumerate(s.options)]
+        elif s.type == "wait":
+            v.waiting = True
+            v.remaining_s = max(0.0, s.timeout_s - (self._clock() - self._wait_started))
+        return v
+
+    # ---------------------------------------------------------- internals
+    def _push(self) -> None:
+        if self.guide and self.step:
+            self._stack.append((self.guide.id, self.step.id))
+
+    def _enter_guide(self, guide_id: str) -> None:
+        self.guide = self.guides[guide_id]
+        self._on_log(f"technician: started guide '{self.guide.title}'")
+        self._enter_step(self.guide.start)
+
+    def _go(self, target: str) -> None:
+        kind, _, ref = target.partition(":")
+        if kind == "end" and ref:
+            self._conclude(self.guide.ends[ref])
+        elif kind == "guide" and ref:
+            self._enter_guide(ref)
+        else:
+            self._enter_step(target)
+
+    def _enter_step(self, step_id: str) -> None:
+        s = self.guide.steps[step_id]
+        self.step, self.note = s, ""
+        if s.skip_if_finding and self._finding_active(s.skip_if_finding):
+            self._auto(s, f"skipped - log already shows {s.skip_if_finding}", s.skip_to)
+            return
+        if s.skip_unless_feature and not self._feature(s.skip_unless_feature):
+            self._auto(s, f"skipped - firmware has no {s.skip_unless_feature}", s.skip_to)
+            return
+        if s.type == "route":
+            target = self._route(s)
+            self._auto(s, f"routed by log findings -> {target}", target)
+            return
+        if s.type == "wait":
+            self._wait_started = self._clock()
+            self._wait_boot = self.engine.boot.index
+            self._wait_milestones = set(self.engine.milestones)
+            if s.tool_action and not self._on_action(s.tool_action):
+                self.note = "Could not restart the box from the tool - connect to it first, or switch it off and on."
+            # A milestone that is already reached satisfies the wait at once
+            # unless the step first restarts the box.
+            if s.until_milestone and not s.tool_action and s.until_milestone in self.engine.milestones:
+                self._record(s, f"already reached: {s.until_milestone}")
+                self._finish_wait("ok")
+
+    def _auto(self, s: Step, why: str, target: str | None) -> None:
+        self._on_log(f"technician guide: {s.id}: {why}")
+        if target:
+            self._go(target)
+
+    def _finish_wait(self, outcome: str) -> None:
+        s = self.step
+        target = {"ok": s.on_ok, "fail": s.on_fail or s.on_timeout, "timeout": s.on_timeout or s.on_fail}[outcome]
+        if target is None:
+            return
+        self._push()
+        self._go(target)
+
+    def _milestone_new(self, mid: str) -> bool:
+        if mid not in self.engine.milestones:
+            return False
+        return self.engine.boot.index != self._wait_boot or mid not in self._wait_milestones
+
+    def _route(self, s: Step) -> str:
+        report = self.engine.report()
+        for rc in report.roots:
+            for f in (rc.finding, *rc.consequences):
+                if f.rule_id in s.routes:
+                    return s.routes[f.rule_id]
+        return s.default or "end:" + next(iter(self.guide.ends))
+
+    def _check_led(self, seen: str) -> None:
+        expected = self.engine.led
+        if expected in ("UNKNOWN", "OFF") or seen == "CYCLING" or seen == expected:
+            return
+        exp_label, see_label = LED[expected][0], LED_ANSWER_LABELS[seen]
+        self.engine.add_confirmed(
+            "tech.led_mismatch", Severity.WARNING,
+            f"LED shows {see_label}, but the log implies {exp_label}",
+            f"The firmware state in the log corresponds to {exp_label}, while the technician sees {see_label}. "
+            "Either the LED just changed (check again in a few seconds), the LED/its wiring is faulty, "
+            "or the box runs different firmware. Trust the log findings.",
+            ("Look at the LED again for 10 seconds.", "If it stays different: note it for repair (LED board)."))
+
+    def _conclude(self, end: End) -> None:
+        self.step, self.end = None, end
+        self._on_log(f"technician guide result: {end.title}")
+        sev = END_SEVERITY[end.severity]
+        self.engine.note_technician(f"{self.guide.title}: {end.title}")
+        if sev is not None:
+            self.engine.add_confirmed(f"tech.{self.guide.id}.{end.id}", sev, end.title, end.text, end.actions)
+
+    def _record(self, s: Step, answer: str) -> None:
+        q = self._render(s.text)
+        self.engine.note_technician(f"{q} -> {answer}")
+        self._on_log(f"technician: {q[:80]} -> {answer}")
+
+    def _finding_active(self, rule_id: str) -> bool:
+        return any(f.rule_id == rule_id and f.active for f in self.engine.findings.values())
+
+    def _feature(self, name: str) -> bool:
+        fw = self.engine.firmware
+        if name == "sd_wifi":
+            return fw.supports_sd_wifi is not False
+        if name == "setup_portal":
+            if fw.known is not None:
+                return fw.known.setup_portal
+            if "setup_portal" in fw.evidence:
+                return True
+            return "legacy_v1" not in fw.evidence   # unknown firmware: ask
+        return False
+
+    def _render(self, text: str) -> str:
+        report = self.engine.report()
+        sensors = sorted({f.title.removesuffix(" failed to start") for f in self.engine.findings.values()
+                          if f.rule_id == "sensor.init_failed" and f.active})
+        ctx = {
+            "expected_led": LED[report.led][0],
+            "failing_sensors": ", ".join(sensors) or "see the Diagnosis tab",
+            "top_finding": report.roots[0].finding.title if report.roots else "none",
+        }
+        return text.format_map(_Fmt(ctx))
+
+
+class _Fmt(dict):
+    def __missing__(self, key: str) -> str:
+        return "{" + key + "}"

kota_tech/diag/guides.toml

@@ -0,0 +1,735 @@
+# Guided troubleshooting: decision trees that combine technician answers
+# with live log evidence (diag.guides.GuideRunner executes them).
+#
+# Guide:  id, title, summary, recommend (rule ids / "led:<COLOUR>" / "always"),
+#         start (first step id), [[guide.step]], [[guide.end]]
+# Step types:
+#   led       technician picks the LED colour; `route` maps colour -> target.
+#             Colours: GREEN PURPLE RED BLUE YELLOW ORANGE WHITE OFF CYCLING
+#             The answer is compared with the colour the firmware log implies.
+#   question  `options` = [{label, next}]
+#   info      instruction + Continue (`next`)
+#   wait      optional `tool_action` ("reset"), then watch the log:
+#             `until` (regex) / `until_milestone`, `fail_on` (regex),
+#             `timeout_s`; go to on_ok / on_fail / on_timeout.
+#             `pass_on_timeout = true`: reaching the timeout without fail_on
+#             counts as ok (used for "watch for N seconds").
+#   route     automatic: first current root finding whose rule id is in
+#             `routes` decides; otherwise `default`.
+# Targets: "<step id>", "end:<end id>", "guide:<guide id>".
+# Optional on any step: skip_if_finding / skip_unless_feature (+ skip_to).
+# Text placeholders: {expected_led} {failing_sensors} {top_finding}
+# End severity: ok | info | warning | error | critical
+
+# ================================================================= quick
+[[guide]]
+id = "quick"
+title = "Quick check - start here"
+summary = "Tell the tool what the LED shows; it picks the right checks."
+recommend = ["always"]
+start = "led"
+
+[[guide.step]]
+id = "led"
+type = "led"
+text = "Look at the RGB status LED on the box (no need to open it). Which colour is it?"
+route = { GREEN = "heartbeat", PURPLE = "guide:network", RED = "guide:sensors", BLUE = "guide:rtc_i2c", WHITE = "guide:white", YELLOW = "guide:update", ORANGE = "guide:update", OFF = "guide:power", CYCLING = "guide:reboot_loop" }
+
+[[guide.step]]
+id = "heartbeat"
+type = "question"
+text = "Is the small LED next to the RGB LED blinking about once per second?"
+options = [
+  { label = "Yes, blinking", next = "green_route" },
+  { label = "No - steady on or off", next = "end:hung" },
+]
+
+[[guide.step]]
+id = "green_route"
+type = "route"
+routes = { "rtc.clock_not_running" = "guide:clock", "mic.silent" = "guide:mic", "mic.disabled" = "guide:mic", "matter.not_commissioned" = "guide:network", "net.dns_fail" = "guide:network" }
+default = "end:healthy"
+
+[[guide.end]]
+id = "healthy"
+severity = "ok"
+title = "Box looks healthy"
+text = "Green LED, firmware running and no problems in the log."
+actions = ["If the customer still reports missing data, keep the tool connected for 5 minutes and check that 'Data uploaded to InfluxDB' gets ticked."]
+
+[[guide.end]]
+id = "hung"
+severity = "error"
+title = "Firmware is not running normally"
+text = "The heartbeat LED should blink once per second whenever the firmware runs. A steady heartbeat LED means the firmware has frozen."
+actions = [
+  "Switch the box off and on with the power switch.",
+  "If it happens again: save the session log and re-flash the official firmware (Flash firmware tab, App only).",
+]
+
+# =============================================================== network
+[[guide]]
+id = "network"
+title = "Purple LED / no Internet"
+summary = "Pairing in Matter, site Wi-Fi and Internet checks, with live confirmation."
+recommend = ["led:PURPLE", "matter.not_commissioned", "net.dns_fail", "influx.buffer_fail", "ota.registration_failed"]
+start = "paired"
+
+[[guide.step]]
+id = "paired"
+type = "question"
+skip_if_finding = "matter.not_commissioned"
+skip_to = "pair_intro"
+text = "Was this box already added to the customer's Matter app (Apple Home, Google Home, ...) at this site?"
+options = [
+  { label = "Yes, it was paired before", next = "internet" },
+  { label = "No / not sure", next = "pair_intro" },
+]
+
+[[guide.step]]
+id = "internet"
+type = "question"
+text = "Does the site Wi-Fi have working Internet? Check with a phone connected to the same Wi-Fi (open any website)."
+options = [
+  { label = "Yes, Internet works", next = "changed" },
+  { label = "No Internet on the site Wi-Fi", next = "end:site_offline" },
+]
+
+[[guide.step]]
+id = "changed"
+type = "question"
+text = "Was the Wi-Fi name or password changed, or the router replaced, since the box was installed?"
+options = [
+  { label = "Yes / possibly", next = "end:repair_needed" },
+  { label = "No", next = "end:offline_unknown" },
+]
+
+[[guide.step]]
+id = "pair_intro"
+type = "info"
+text = "The box is not on any Wi-Fi yet: it must be paired in Matter. You need: a phone with Bluetooth on, the customer's Matter app, the 2.4 GHz Wi-Fi password, and the QR sticker of this box. Keep the tool connected - it follows the pairing live."
+next = "pair_start"
+
+[[guide.step]]
+id = "pair_start"
+type = "wait"
+text = "In the Matter app choose 'Add device' and scan the QR code shown here (the same as the sticker), or type the 11-digit manual code. Keep the phone within 1 m of the box."
+show_qr = true
+until = 'MAIN: Commissioning session started'
+timeout_s = 300
+on_ok = "pair_wifi"
+on_timeout = "not_found"
+
+[[guide.step]]
+id = "not_found"
+type = "question"
+text = "The box has not seen the phone connect yet. What does the app show?"
+options = [
+  { label = "Still searching / let me try again", next = "pair_start" },
+  { label = "'Device not found' or similar", next = "end:ble_not_found" },
+]
+
+[[guide.step]]
+id = "pair_wifi"
+type = "wait"
+text = "The phone is connected to the box. Follow the app: choose the 2.4 GHz Wi-Fi network and enter its password."
+until = 'MAIN: Commissioning complete|MAIN: Fabric is committed'
+fail_on = 'Commissioning failed, fail safe timer expired'
+timeout_s = 300
+on_ok = "pair_time"
+on_fail = "end:pair_failed"
+on_timeout = "end:pair_failed"
+
+[[guide.step]]
+id = "pair_time"
+type = "wait"
+text = "Paired! The box is joining the Wi-Fi and getting the time from the Internet..."
+until_milestone = "time_synced"
+timeout_s = 120
+on_ok = "pair_upload"
+on_timeout = "end:joined_no_internet"
+
+[[guide.step]]
+id = "pair_upload"
+type = "wait"
+text = "Online. Waiting for the first measurements to reach the database (up to 4 minutes)..."
+until = 'INFLUX: HTTP request performed, status code: 2\d\d'
+fail_on = 'INFLUX: Failed to perform HTTP request: (401|403|404)'
+timeout_s = 240
+on_ok = "end:online"
+on_fail = "end:influx_rejected"
+on_timeout = "end:no_upload"
+
+[[guide.end]]
+id = "online"
+severity = "ok"
+title = "Box is paired and uploading data"
+text = "Pairing, Internet time and the first upload all worked."
+actions = [
+  "The box may now download a firmware update (yellow, then orange LED, a few minutes). Do not switch it off.",
+  "It should end green.",
+]
+
+[[guide.end]]
+id = "site_offline"
+severity = "warning"
+title = "Site network has no Internet"
+text = "The box cannot work until the site Wi-Fi reaches the Internet. This is not a box fault."
+actions = ["Ask the customer to fix the Internet connection, then power-cycle the box."]
+
+[[guide.end]]
+id = "repair_needed"
+severity = "warning"
+title = "Box must be paired again"
+text = "The box still remembers the old Wi-Fi. It needs a factory reset and new pairing."
+actions = [
+  "Hold the Matter button for 5 seconds (LED turns white) - this erases the old pairing.",
+  "Remove the box from the customer's Matter app, then run this guide again and choose 'No / not sure'.",
+]
+
+[[guide.end]]
+id = "offline_unknown"
+severity = "error"
+title = "Box is paired but cannot reach the Internet - cause unclear"
+text = "The network works for other devices, but not for this box."
+actions = [
+  "Check the router does not block new devices (guest isolation, MAC filter). Box MAC is shown in the port list.",
+  "Move the box closer to the router to rule out weak signal.",
+  "If nothing helps: factory reset (hold the Matter button 5 s) and pair again.",
+]
+
+[[guide.end]]
+id = "ble_not_found"
+severity = "error"
+title = "Phone cannot find the box over Bluetooth"
+text = "The box only accepts pairing for a limited time after start-up."
+actions = [
+  "Switch the box off and on to reopen the pairing window, then try again within 10 minutes.",
+  "Check Bluetooth and location permission are on for the Matter app.",
+  "If the box was paired to another app before: hold the Matter button 5 s (factory reset) first.",
+]
+
+[[guide.end]]
+id = "pair_failed"
+severity = "error"
+title = "Pairing did not finish"
+text = "The phone connected but the box did not join the Wi-Fi."
+actions = [
+  "Use a 2.4 GHz network (many routers have a separate 2.4 GHz name).",
+  "Re-enter the Wi-Fi password carefully.",
+  "Switch the box off and on, then pair again.",
+]
+
+[[guide.end]]
+id = "joined_no_internet"
+severity = "error"
+title = "Box joined the Wi-Fi but has no Internet"
+text = "Pairing worked, but the box cannot reach time or data servers."
+actions = [
+  "Check the network allows outgoing connections (HTTPS, NTP) for new devices.",
+  "Try a phone hotspot to rule out the site network.",
+]
+
+[[guide.end]]
+id = "influx_rejected"
+severity = "critical"
+title = "Database rejected the box (token / bucket)"
+text = "The box is online but InfluxDB refused the upload. The SD card settings are wrong."
+actions = ["Re-provision the SD card with the current ENV.TXT (SD card is inside the case)."]
+
+[[guide.end]]
+id = "no_upload"
+severity = "warning"
+title = "Online, but no upload seen yet"
+text = "Uploads happen every minute; the first one can be delayed while the air sensor warms up."
+actions = ["Keep the tool connected a few more minutes and watch the Diagnosis tab."]
+
+# ================================================================= RTC / I2C
+[[guide]]
+id = "rtc_i2c"
+title = "Blue LED - clock / I2C cable"
+summary = "Re-seat the I2C cable and verify the start-up live."
+recommend = ["led:BLUE", "rtc.init_failed", "i2c.errors"]
+start = "explain"
+
+[[guide.step]]
+id = "explain"
+type = "info"
+text = "Blue means the clock chip did not answer. It is the first chip on the shared I2C cable between the boards, so a loose cable is the most common cause. This check needs the case opened."
+next = "reseat"
+
+[[guide.step]]
+id = "reseat"
+type = "info"
+text = "Switch the power OFF. Open the case. Unplug and firmly re-plug the I2C cable between the boards at both ends. Close the case and switch the power ON. Then press Continue."
+next = "verify"
+
+[[guide.step]]
+id = "verify"
+type = "wait"
+text = "Watching the start-up (up to 60 s)..."
+until_milestone = "sensors_ready"
+fail_on = 'MAIN: Failed to initialize RTC'
+timeout_s = 60
+on_ok = "end:i2c_fixed"
+on_fail = "damaged"
+on_timeout = "damaged"
+
+[[guide.step]]
+id = "damaged"
+type = "question"
+text = "The clock still does not answer. Is the I2C cable or its connector visibly damaged (pinched, broken wire, bent pin)?"
+options = [
+  { label = "Yes, damaged", next = "end:replace_cable" },
+  { label = "No, looks fine", next = "end:rtc_module" },
+]
+
+[[guide.end]]
+id = "i2c_fixed"
+severity = "ok"
+title = "Fixed - all sensors start again"
+text = "After re-seating the cable the clock and all sensors started."
+actions = ["Make sure the cable is routed without strain before closing the case."]
+
+[[guide.end]]
+id = "replace_cable"
+severity = "error"
+title = "Replace the I2C cable"
+text = "A damaged I2C cable stops the clock and all sensors."
+actions = ["Replace the cable, then run this check again."]
+
+[[guide.end]]
+id = "rtc_module"
+severity = "error"
+title = "Clock (RTC) module is probably faulty"
+text = "The cable is fine but the clock chip does not answer."
+actions = ["Replace the RTC module, or send the box for repair with the session log."]
+
+# ==================================================================== white
+[[guide]]
+id = "white"
+title = "White LED - SD card / reset / setup mode"
+summary = "Tell apart the three white states and check the SD card."
+recommend = ["led:WHITE", "sd.card_fail", "sd.mount_fail", "sd.env_open_fail", "influx.env_missing", "influx.init_fail"]
+start = "button"
+
+[[guide.step]]
+id = "button"
+type = "question"
+text = "Did anyone hold the Matter button (outside the case) for about 5 seconds just before the LED turned white?"
+options = [
+  { label = "Yes", next = "end:factory_reset" },
+  { label = "No / don't know", next = "portal" },
+]
+
+[[guide.step]]
+id = "portal"
+type = "question"
+skip_unless_feature = "setup_portal"
+skip_to = "sd_reseat"
+text = "On a phone, look at the Wi-Fi list: is there a network called 'KotaSensorBox-....'?"
+options = [
+  { label = "Yes", next = "end:setup_mode" },
+  { label = "No", next = "sd_reseat" },
+]
+
+[[guide.step]]
+id = "sd_reseat"
+type = "info"
+text = "The SD card is probably not readable. This needs the case opened: switch the power OFF, open the case, push the SD card in until it clicks (or remove and re-insert it). Close the case, switch the power ON, then press Continue."
+next = "sd_verify"
+
+[[guide.step]]
+id = "sd_verify"
+type = "wait"
+text = "Watching the SD card start-up (up to 60 s)..."
+until = 'Read INFLUX_URL from \.env file'
+fail_on = 'Failed to initialize the card|Failed to mount filesystem|Failed to read INFLUX_(URL|TOKEN)|Failed to open \.env file'
+timeout_s = 60
+on_ok = "end:sd_fixed"
+on_fail = "end:sd_reprovision"
+on_timeout = "end:sd_reprovision"
+
+[[guide.end]]
+id = "factory_reset"
+severity = "info"
+title = "White = factory reset in progress"
+text = "The box erased its Matter pairing and restarts."
+actions = ["Pair it again in the Matter app (Purple LED guide)."]
+
+[[guide.end]]
+id = "setup_mode"
+severity = "info"
+title = "White = Wi-Fi setup mode"
+text = "The box is waiting for Wi-Fi settings on its own network."
+actions = [
+  "Connect a phone to KotaSensorBox-.... and open http://sensorbox.local/ to enter the Wi-Fi,",
+  "or short-press the Matter button (< 2 s) to leave setup mode.",
+]
+
+[[guide.end]]
+id = "sd_fixed"
+severity = "ok"
+title = "Fixed - SD card is read again"
+text = "The box found the SD card and read ENV.TXT."
+actions = ["Close the case and watch the Diagnosis tab for a minute."]
+
+[[guide.end]]
+id = "sd_reprovision"
+severity = "critical"
+title = "SD card is unreadable or has wrong settings"
+text = "Even after re-seating, the card or its ENV.TXT cannot be used."
+actions = [
+  "Re-provision the card with the tool (SD card tab) or use a new card.",
+  "The Diagnosis tab shows which step failed (card, file system or ENV.TXT keys).",
+]
+
+# ================================================================== sensors
+[[guide]]
+id = "sensors"
+title = "Red LED - sensor or hardware fault"
+summary = "Find the failing sensor and verify after re-seating its cable."
+recommend = ["led:RED", "sensor.init_failed", "sensor.selfcheck_failed", "sys.out_of_resources", "ota.selfcheck_failed"]
+start = "which"
+
+[[guide.step]]
+id = "which"
+type = "route"
+routes = { "sensor.init_failed" = "reseat", "rtc.init_failed" = "guide:rtc_i2c", "ota.selfcheck_failed" = "end:selfcheck", "sensor.selfcheck_failed" = "end:selfcheck", "sys.out_of_resources" = "end:oom" }
+default = "capture"
+
+[[guide.step]]
+id = "capture"
+type = "wait"
+text = "The log does not show the cause yet. The tool restarts the box and records its start-up (45 s)..."
+tool_action = "reset"
+timeout_s = 45
+pass_on_timeout = true
+on_ok = "which_again"
+
+[[guide.step]]
+id = "which_again"
+type = "route"
+routes = { "sensor.init_failed" = "reseat", "rtc.init_failed" = "guide:rtc_i2c", "sys.out_of_resources" = "end:oom" }
+default = "end:red_unclear"
+
+[[guide.step]]
+id = "reseat"
+type = "info"
+text = "Failing: {failing_sensors}. This needs the case opened: switch the power OFF, open the case and re-seat the cable of that sensor. Close the case, switch the power ON, then press Continue."
+next = "verify"
+
+[[guide.step]]
+id = "verify"
+type = "wait"
+text = "Watching the sensor start-up (up to 60 s)..."
+until_milestone = "sensors_ready"
+fail_on = 'MAIN: Failed to initialize'
+timeout_s = 60
+on_ok = "end:sensor_fixed"
+on_fail = "end:sensor_replace"
+on_timeout = "end:sensor_replace"
+
+[[guide.end]]
+id = "sensor_fixed"
+severity = "ok"
+title = "Fixed - all sensors start again"
+text = "After re-seating, every sensor started."
+actions = ["Close the case and watch the Diagnosis tab for a minute."]
+
+[[guide.end]]
+id = "sensor_replace"
+severity = "error"
+title = "Sensor still fails - replace it"
+text = "The sensor does not start even with a re-seated cable."
+actions = ["Replace the named sensor (or its cable) and run this check again."]
+
+[[guide.end]]
+id = "selfcheck"
+severity = "error"
+title = "A firmware update was rejected by its self-check"
+text = "The box rolled back to its previous firmware because a sensor failed the test."
+actions = ["Check the sensor named in the Diagnosis tab (inside the case), then power-cycle."]
+
+[[guide.end]]
+id = "oom"
+severity = "error"
+title = "Firmware ran out of memory"
+text = "Not a hardware fault; the firmware restarts itself."
+actions = ["Power-cycle. If it repeats, send the session log to the firmware team."]
+
+[[guide.end]]
+id = "red_unclear"
+severity = "warning"
+title = "Red LED without a clear cause in the log"
+text = "The start-up did not show a failing sensor."
+actions = ["Save the session log and send it to the firmware team."]
+
+# ============================================================= reboot loop
+[[guide]]
+id = "reboot_loop"
+title = "LED keeps changing / box restarts"
+summary = "Record several start-ups and find the error just before each restart."
+recommend = ["led:CYCLING", "reboot.loop", "sys.crash", "reboot.unexpected", "reboot.brownout", "reboot.watchdog"]
+start = "record"
+
+[[guide.step]]
+id = "record"
+type = "wait"
+text = "The tool restarts the box and records 45 seconds of start-up..."
+tool_action = "reset"
+timeout_s = 45
+pass_on_timeout = true
+on_ok = "cause"
+
+[[guide.step]]
+id = "cause"
+type = "route"
+routes = { "rtc.init_failed" = "guide:rtc_i2c", "sd.card_fail" = "guide:white", "sd.mount_fail" = "guide:white", "sd.env_open_fail" = "guide:white", "influx.env_missing" = "guide:white", "influx.init_fail" = "guide:white", "sensor.init_failed" = "guide:sensors", "reboot.brownout" = "end:power_supply", "matter.not_commissioned" = "guide:network", "net.dns_fail" = "guide:network", "influx.buffer_fail" = "guide:network" }
+default = "end:loop_unclear"
+
+[[guide.end]]
+id = "power_supply"
+severity = "error"
+title = "Power supply is too weak or unstable"
+text = "The chip reset itself because the voltage dropped."
+actions = ["Check the power supply, cable and connectors; try another supply."]
+
+[[guide.end]]
+id = "loop_unclear"
+severity = "warning"
+title = "No clear restart cause in 45 s"
+text = "The box did not show a known start-up error during the recording."
+actions = ["Keep the tool connected for 5 minutes, then save the session log for the firmware team."]
+
+# ================================================================== update
+[[guide]]
+id = "update"
+title = "Yellow / orange LED - firmware update"
+summary = "Wait for the update and its self-check to finish."
+recommend = ["led:YELLOW", "led:ORANGE", "ota.updating", "ota.selfcheck"]
+start = "wait"
+
+[[guide.step]]
+id = "wait"
+type = "wait"
+text = "A firmware update or its self-check is running. Do NOT switch the box off. Waiting up to 10 minutes..."
+until = 'Passing selfcheck|OTA update successful'
+fail_on = 'OTA update failed|Failing selfcheck'
+timeout_s = 600
+on_ok = "end:update_ok"
+on_fail = "end:update_failed"
+on_timeout = "end:update_slow"
+
+[[guide.end]]
+id = "update_ok"
+severity = "ok"
+title = "Update finished"
+text = "The new firmware was installed or accepted."
+actions = ["Wait for the green LED."]
+
+[[guide.end]]
+id = "update_failed"
+severity = "error"
+title = "Update failed"
+text = "The box keeps its current firmware and retries later."
+actions = ["Check the Wi-Fi is stable. The Diagnosis tab shows why it failed."]
+
+[[guide.end]]
+id = "update_slow"
+severity = "warning"
+title = "Update is taking very long"
+text = "No end of the update was seen in 10 minutes."
+actions = ["Check the Wi-Fi signal; leave the box powered and check again later."]
+
+# =================================================================== power
+[[guide]]
+id = "power"
+title = "LED off"
+summary = "Power switch, heartbeat LED and USB connection."
+recommend = ["led:OFF"]
+start = "switch"
+
+[[guide.step]]
+id = "switch"
+type = "question"
+text = "Is the power switch on the outside of the case set to ON?"
+options = [
+  { label = "It was OFF - I switched it on", next = "boot" },
+  { label = "It is ON", next = "heartbeat" },
+]
+
+[[guide.step]]
+id = "boot"
+type = "wait"
+text = "Waiting for the box to start (up to 30 s)..."
+until_milestone = "app_started"
+timeout_s = 30
+on_ok = "end:was_off"
+on_timeout = "heartbeat"
+
+[[guide.step]]
+id = "heartbeat"
+type = "question"
+text = "Is the small LED next to the RGB LED blinking?"
+options = [
+  { label = "Yes, blinking", next = "end:rgb_led_fault" },
+  { label = "No", next = "end:no_power" },
+]
+
+[[guide.end]]
+id = "was_off"
+severity = "ok"
+title = "Box was switched off"
+text = "It starts normally after switching on."
+actions = ["Run the Quick check again once the LED shows a colour."]
+
+[[guide.end]]
+id = "rgb_led_fault"
+severity = "warning"
+title = "Firmware runs, but the RGB LED stays dark"
+text = "The heartbeat LED shows the firmware is running; the RGB LED or its wiring is faulty."
+actions = ["Use the Diagnosis tab instead of the LED; replace the LED board when convenient."]
+
+[[guide.end]]
+id = "no_power"
+severity = "error"
+title = "Box does not start"
+text = "Neither LED is lit: no power or the firmware does not start."
+actions = [
+  "Check the power supply and cable.",
+  "If the USB port shows up in this tool, re-flash the official firmware (Flash firmware tab, App only).",
+]
+
+# =================================================================== clock
+[[guide]]
+id = "clock"
+title = "Clock not set"
+summary = "Why readings are on hold and when the coin cell matters."
+recommend = ["rtc.clock_not_running", "rtc.lost_after_sync"]
+start = "internet"
+
+[[guide.step]]
+id = "internet"
+type = "question"
+text = "The box clock is not set, so readings are on hold. Will the box have Internet at its installation site?"
+options = [
+  { label = "Yes", next = "end:clock_auto" },
+  { label = "No / not yet", next = "end:clock_offline" },
+]
+
+[[guide.end]]
+id = "clock_auto"
+severity = "info"
+title = "Clock will be set automatically"
+text = "On its first Internet connection the box sets its clock and starts recording."
+actions = ["If the clock is lost again after every power-off, replace the RTC coin cell (inside the case)."]
+
+[[guide.end]]
+id = "clock_offline"
+severity = "error"
+title = "Box will not record data without Internet"
+text = "Without the Internet the clock cannot be set, and the firmware holds all readings until it is."
+actions = [
+  "Give the box Internet access (pair it in Matter).",
+  "Replace the RTC coin cell (inside the case) so the time survives power-offs.",
+]
+
+# ===================================================================== mic
+[[guide]]
+id = "mic"
+title = "Microphone check"
+summary = "Switched-off or silent microphone."
+recommend = ["mic.disabled", "mic.silent", "mic.read_fail"]
+start = "which"
+
+[[guide.step]]
+id = "which"
+type = "route"
+routes = { "mic.disabled" = "switch", "mic.silent" = "clap", "mic.read_fail" = "end:mic_faulty" }
+default = "clap"
+
+[[guide.step]]
+id = "switch"
+type = "question"
+text = "The box reads its microphone switch as OFF. The switch is on the back of the case, just above the power switch (no need to open the box). Should this box measure noise?"
+options = [
+  { label = "Yes - I flipped the microphone switch", next = "switch_verify" },
+  { label = "No - it is meant to be off", next = "end:mic_off_ok" },
+]
+
+[[guide.step]]
+id = "switch_verify"
+type = "wait"
+# The firmware re-reads the switch before every reading (~10 s): no restart needed.
+text = "Waiting for the next microphone reading (up to 30 s)..."
+until = 'MICROPHONE: Read \d+ bytes'
+fail_on = 'Microphone is in shutdown state'
+timeout_s = 30
+on_ok = "end:mic_on"
+on_fail = "flip_back"
+on_timeout = "flip_back"
+
+[[guide.step]]
+id = "flip_back"
+type = "question"
+text = "The box still reads the switch as OFF. Flip the microphone switch to the other position (it may have been ON already)."
+options = [
+  { label = "Done - I flipped it to the other position", next = "switch_verify2" },
+  { label = "Leave it off", next = "end:mic_off_ok" },
+]
+
+[[guide.step]]
+id = "switch_verify2"
+type = "wait"
+text = "Waiting for the next microphone reading (up to 30 s)..."
+until = 'MICROPHONE: Read \d+ bytes'
+fail_on = 'Microphone is in shutdown state'
+timeout_s = 30
+on_ok = "end:mic_on"
+on_fail = "end:mic_switch_faulty"
+on_timeout = "end:mic_switch_faulty"
+
+[[guide.step]]
+id = "clap"
+type = "wait"
+text = "Check the microphone switch (back of the case, above the power switch) is ON. Then clap your hands or speak loudly right next to the box for about 20 seconds..."
+until = 'dB peak: (?!-inf)'
+timeout_s = 45
+on_ok = "end:mic_ok"
+on_timeout = "end:mic_faulty"
+
+[[guide.end]]
+id = "mic_on"
+severity = "ok"
+title = "Microphone is on and recording"
+text = "The firmware reads audio samples again."
+actions = ["Leave the microphone switch in this position."]
+
+[[guide.end]]
+id = "mic_off_ok"
+severity = "info"
+title = "Microphone intentionally off"
+text = "No noise data is recorded for this box; everything else works."
+actions = []
+
+[[guide.end]]
+id = "mic_switch_faulty"
+severity = "warning"
+title = "Microphone switch has no effect"
+text = "The box reads the microphone as OFF in both switch positions (enable line GPIO3)."
+actions = ["Check the switch and its cable to the main board (inside the case); replace the switch if needed."]
+
+[[guide.end]]
+id = "mic_ok"
+severity = "ok"
+title = "Microphone works"
+text = "It picked up sound - the earlier silence was just a very quiet room."
+actions = []
+
+[[guide.end]]
+id = "mic_faulty"
+severity = "error"
+title = "Microphone records nothing"
+text = "Even loud noise next to the box gives no signal, although the switch is on."
+actions = ["Check the microphone board/cable (inside the case); replace the microphone if needed."]

kota_tech/diag/rules.toml

@@ -72,6 +72,13 @@ severity = "ignore"
 milestone = "wifi_connected"
 clears = ["matter.not_commissioned", "wifi.disconnected"]
 
+[[rule]]
+id = "matter.commissioned"
+pattern = 'MAIN: Commissioning complete|MAIN: Fabric is committed'
+severity = "ignore"
+milestone = "matter_commissioned"
+clears = ["matter.not_commissioned", "matter.commissioning_failed"]
+
 [[rule]]
 id = "net.time_synced"
 pattern = 'SNTP: Time synchronized'
@@ -551,8 +558,8 @@ id = "mic.disabled"
 pattern = 'MICROPHONE: Microphone is in shutdown state'
 severity = "info"
 title = "Microphone is switched off - no noise measurements"
-meaning = "The firmware reads the microphone enable line (GPIO3) as 'off', which it treats as disabled on purpose. Noise levels are not recorded."
+meaning = "The microphone switch on the back of the case (just above the power switch) is OFF, so noise levels are not recorded."
-actions = ["If this box should measure noise: check the microphone enable switch/jumper and its wiring (inside the case)."]
+actions = ["If this box should measure noise: flip the microphone switch (back of the case, above the power switch). No restart needed - it is picked up within about 10 s."]
 
 [[rule]]
 id = "gather.empty_reading"

kota_tech/flash/image.py

@@ -0,0 +1,303 @@
+"""Firmware images: validation, integrity and layout.
+
+Two origins:
+  * factory   - bundled with the tool (firmware/firmware.toml), SHA-256 locked;
+  * developer - a newer build the firmware team sends to technicians,
+                imported into a per-user library (~/KotaTechnicianTool/firmware).
+Two kinds:
+  * merged - bootloader at 0x0 + partition table + app (like new_system.bin);
+             App-only or Full flashing;
+  * app    - the application binary only (build/kota-sensorboard.bin);
+             App-only flashing, laid out like the factory image.
+
+Every image is checked structurally (ESP32-S3, kota-sensorboard app
+descriptor, segment checksum and the appended SHA-256) so a truncated or
+corrupted file is refused before anything is written.
+"""
+
+from __future__ import annotations
+
+import datetime as dt
+import hashlib
+import json
+import shutil
+import struct
+import tomllib
+from dataclasses import dataclass
+from pathlib import Path
+
+FIRMWARE_DIR = Path(__file__).resolve().parents[2] / "firmware"
+MANIFEST = FIRMWARE_DIR / "firmware.toml"
+LIBRARY_DIR = Path.home() / "KotaTechnicianTool" / "firmware"
+LIBRARY_INDEX = "library.json"
+
+PT_OFFSET = 0x8000
+PT_SIZE = 0xC00
+ESP32S3_CHIP_ID = 9
+IMAGE_MAGIC = 0xE9
+APP_DESC_MAGIC = 0xABCD5432
+FLASH_SIZES = {0: "1MB", 1: "2MB", 2: "4MB", 3: "8MB", 4: "16MB", 5: "32MB"}
+_MONTHS = {m: i for i, m in enumerate(
+    ["Jan", "Feb", "Mar", "Apr", "May", "Jun", "Jul", "Aug", "Sep", "Oct", "Nov", "Dec"], 1)}
+
+
+class ImageError(ValueError):
+    pass
+
+
+@dataclass(frozen=True)
+class Partition:
+    label: str
+    type: int
+    subtype: int
+    offset: int
+    size: int
+
+
+@dataclass(frozen=True)
+class AppInfo:
+    project: str
+    version: str
+    built: str          # "Jun 29 2026 11:03:32" as in the app descriptor
+    idf: str
+    elf_sha: str        # hex
+
+    @property
+    def built_at(self) -> dt.datetime | None:
+        try:
+            mon, day, year, hms = self.built.split()
+            h, m, s = (int(x) for x in hms.split(":"))
+            return dt.datetime(int(year), _MONTHS[mon], int(day), h, m, s)
+        except (ValueError, KeyError):
+            return None
+
+
+@dataclass(frozen=True)
+class FirmwareImage:
+    path: Path
+    name: str
+    notes: str
+    origin: str                      # "factory" | "developer"
+    kind: str                        # "merged" | "app"
+    sha256: str
+    flash_size: str
+    partitions: tuple[Partition, ...]
+    partition_table: bytes           # expected table on the box
+    app_offset: int                  # where the app starts inside the file
+    app_length: int                  # exact app image length (from its structure)
+    app: AppInfo
+    built_by: str = ""               # who compiled a developer build (shown in the UI)
+
+    @property
+    def data(self) -> bytes:
+        return self.path.read_bytes()
+
+    @property
+    def is_developer(self) -> bool:
+        return self.origin == "developer"
+
+    def partition(self, label: str) -> Partition:
+        for p in self.partitions:
+            if p.label == label:
+                return p
+        raise ImageError(f"partition {label!r} not in image")
+
+    def app_bytes(self) -> bytes:
+        return self.data[self.app_offset:self.app_offset + self.app_length]
+
+    def blank_otadata(self) -> bytes:
+        """Erased otadata: the bootloader then boots ota_0."""
+        return b"\xff" * self.partition("otadata").size
+
+    def label(self) -> str:
+        if self.origin == "factory":
+            tag = "factory"
+        else:
+            tag = "developer build" + (f" - built by {self.built_by}" if self.built_by else "")
+        return f"{self.app.version} built {self.app.built} [{self.app.elf_sha[:9]}] - {tag}"
+
+
+# ---------------------------------------------------------------- parsing
+
+def parse_partition_table(raw: bytes) -> tuple[Partition, ...]:
+    parts = []
+    for i in range(0, len(raw) - 31, 32):
+        entry = raw[i:i + 32]
+        magic = entry[:2]
+        if magic == b"\xaa\x50":
+            _, ptype, sub, off, size = struct.unpack_from("<HBBII", entry)
+            label = entry[12:28].split(b"\0")[0].decode("ascii", "replace")
+            parts.append(Partition(label, ptype, sub, off, size))
+        elif magic in (b"\xeb\xeb", b"\xff\xff"):   # MD5 entry / end
+            break
+        else:
+            raise ImageError(f"corrupt partition table entry at 0x{PT_OFFSET + i:x}")
+    return tuple(parts)
+
+
+def app_image_length(data: bytes, offset: int = 0) -> int:
+    """Validate an ESP app image at `offset`; return its exact length.
+
+    Checks the segment checksum and, when the header says so, the appended
+    SHA-256 - the same checks the bootloader performs before booting it.
+    """
+    if len(data) < offset + 24 or data[offset] != IMAGE_MAGIC:
+        raise ImageError(f"no firmware image at 0x{offset:x}")
+    segments = data[offset + 1]
+    chip_id = struct.unpack_from("<H", data, offset + 12)[0]
+    if chip_id != ESP32S3_CHIP_ID:
+        raise ImageError(f"image is for chip id {chip_id}, not ESP32-S3")
+    hash_appended = data[offset + 23] == 1
+    pos, checksum = offset + 24, 0xEF
+    for _ in range(segments):
+        if pos + 8 > len(data):
+            raise ImageError("image is truncated (segment header missing)")
+        _, seg_len = struct.unpack_from("<II", data, pos)
+        pos += 8
+        if pos + seg_len > len(data):
+            raise ImageError("image is truncated (segment data missing)")
+        for b in data[pos:pos + seg_len]:
+            checksum ^= b
+        pos += seg_len
+    pos += 15 - ((pos - offset) % 16)          # pad so the checksum ends a 16-byte block
+    if pos >= len(data) or data[pos] != checksum:
+        raise ImageError("image checksum is wrong - the file is corrupted")
+    pos += 1
+    if hash_appended:
+        if pos + 32 > len(data):
+            raise ImageError("image is truncated (SHA-256 missing)")
+        if hashlib.sha256(data[offset:pos]).digest() != data[pos:pos + 32]:
+            raise ImageError("image SHA-256 does not match its content - the file is corrupted")
+        pos += 32
+    return pos - offset
+
+
+def _app_info(data: bytes, offset: int) -> AppInfo:
+    d = data[offset + 0x20:offset + 0x20 + 256]
+    if len(d) < 256 or struct.unpack_from("<I", d)[0] != APP_DESC_MAGIC:
+        raise ImageError("firmware has no ESP-IDF app descriptor")
+    s = lambda o, n: d[o:o + n].split(b"\0")[0].decode("ascii", "replace")
+    info = AppInfo(project=s(48, 32), version=s(16, 32), built=f"{s(96, 16)} {s(80, 16)}",
+                   idf=s(112, 32), elf_sha=d[144:176].hex())
+    if info.project != "kota-sensorboard":
+        raise ImageError(f"firmware is {info.project!r}, not kota-sensorboard")
+    return info
+
+
+def inspect_image(path: Path, name: str = "", notes: str = "", origin: str = "factory",
+                  reference: FirmwareImage | None = None, built_by: str = "") -> FirmwareImage:
+    """Validate a merged or app-only image. App-only images need a `reference`
+    (the factory image) that provides the flash layout."""
+    data = path.read_bytes()
+    if len(data) >= PT_OFFSET + PT_SIZE and data[0] == IMAGE_MAGIC and data[PT_OFFSET:PT_OFFSET + 2] == b"\xaa\x50":
+        app_image_length(data, 0)              # bootloader must be intact
+        table = data[PT_OFFSET:PT_OFFSET + PT_SIZE]
+        parts = parse_partition_table(table)
+        labels = {p.label for p in parts}
+        for need in ("nvs", "otadata", "ota_0"):
+            if need not in labels:
+                raise ImageError(f"partition table has no {need!r} partition")
+        ota0 = next(p for p in parts if p.label == "ota_0")
+        kind, app_off, flash_size = "merged", ota0.offset, FLASH_SIZES.get(data[3] >> 4, "?")
+    elif data[:1] == bytes([IMAGE_MAGIC]):
+        if reference is None:
+            raise ImageError("app-only image needs the factory image as layout reference")
+        kind, app_off = "app", 0
+        parts, table, flash_size = reference.partitions, reference.partition_table, reference.flash_size
+        ota0 = next(p for p in parts if p.label == "ota_0")
+    else:
+        raise ImageError("not an ESP32 firmware file")
+    length = app_image_length(data, app_off)
+    if length > ota0.size:
+        raise ImageError(f"firmware ({length} bytes) does not fit the ota_0 partition ({ota0.size} bytes)")
+    app = _app_info(data, app_off)
+    return FirmwareImage(path, name or path.name, notes, origin, kind, hashlib.sha256(data).hexdigest(),
+                         flash_size, parts, table, app_off, length, app, built_by)
+
+
+# ------------------------------------------------------------- catalogue
+
+def bundled_images(manifest: Path = MANIFEST) -> list[FirmwareImage]:
+    """Images shipped with the tool whose file exists and matches its SHA-256.
+    Factory images first; bundled developer builds keep their origin/built_by."""
+    if not manifest.exists():
+        return []
+    out = []
+    for e in tomllib.loads(manifest.read_text(encoding="utf-8")).get("image", []):
+        path = manifest.parent / e["file"]
+        if not path.exists():
+            continue
+        origin = e.get("origin", "factory")
+        if origin not in ("factory", "developer"):
+            raise ImageError(f"{path.name}: unknown origin {origin!r} in the manifest")
+        img = inspect_image(path, e.get("name", ""), e.get("notes", ""), origin, built_by=e.get("built_by", ""))
+        if img.sha256 != e["sha256"].lower():
+            raise ImageError(f"{path.name}: SHA-256 does not match the manifest - file changed or corrupt")
+        out.append(img)
+    return sorted(out, key=lambda i: i.origin != "factory")
+
+
+def factory_images(manifest: Path = MANIFEST) -> list[FirmwareImage]:
+    """Only the official factory image(s)."""
+    return [i for i in bundled_images(manifest) if i.origin == "factory"]
+
+
+class FirmwareLibrary:
+    """Developer builds imported by the technician (persist across tool versions)."""
+
+    def __init__(self, root: Path = LIBRARY_DIR):
+        self.root = root
+
+    def _index(self) -> list[dict]:
+        f = self.root / LIBRARY_INDEX
+        return json.loads(f.read_text(encoding="utf-8")) if f.exists() else []
+
+    def _save(self, entries: list[dict]) -> None:
+        self.root.mkdir(parents=True, exist_ok=True)
+        (self.root / LIBRARY_INDEX).write_text(json.dumps(entries, indent=2), encoding="utf-8")
+
+    def images(self, reference: FirmwareImage | None) -> tuple[list[FirmwareImage], list[str]]:
+        """(valid images, problems) - a changed or broken file is reported, not offered."""
+        imgs, problems = [], []
+        for e in self._index():
+            path = self.root / e["file"]
+            try:
+                img = inspect_image(path, e.get("name", ""), e.get("notes", ""), "developer", reference,
+                                    e.get("built_by", ""))
+                if img.sha256 != e["sha256"]:
+                    raise ImageError("file changed since it was imported")
+                imgs.append(img)
+            except (OSError, ImageError) as exc:
+                problems.append(f"{e.get('original', e['file'])}: {exc}")
+        return imgs, problems
+
+    def import_file(self, src: Path, reference: FirmwareImage | None, notes: str = "",
+                    built_by: str = "") -> FirmwareImage:
+        img = inspect_image(src, origin="developer", reference=reference)   # validate before copying
+        entries = self._index()
+        existing = next((e for e in entries if e["sha256"] == img.sha256), None)
+        if existing:
+            return inspect_image(self.root / existing["file"], existing["name"], existing["notes"],
+                                 "developer", reference, existing.get("built_by", ""))
+        self.root.mkdir(parents=True, exist_ok=True)
+        fname = f"{img.app.elf_sha[:9]}_{img.sha256[:8]}.bin"
+        shutil.copyfile(src, self.root / fname)
+        built_by = built_by.strip()
+        name = f"Developer build {img.app.version} ({img.app.built})" + (f", built by {built_by}" if built_by else "")
+        entries.append({"file": fname, "sha256": img.sha256, "name": name, "original": src.name,
+                        "imported": dt.datetime.now().isoformat(timespec="seconds"), "notes": notes,
+                        "built_by": built_by})
+        self._save(entries)
+        return inspect_image(self.root / fname, name, notes, "developer", reference, built_by)
+
+    def remove(self, sha256: str) -> None:
+        entries = self._index()
+        keep = [e for e in entries if e["sha256"] != sha256]
+        for e in entries:
+            if e["sha256"] == sha256:
+                (self.root / e["file"]).unlink(missing_ok=True)
+        self._save(keep)
+
+
+# Backwards-compatible name used by earlier callers/tests.
+official_images = factory_images

kota_tech/flash/plan.py

@@ -0,0 +1,104 @@
+"""Flash plans: which esptool steps run, in which order.
+
+App-only (default, repairs): check the box has the same partition table,
+then write the app to ota_0 and erase otadata so ota_0 boots. NVS is kept:
+Matter pairing, OTA registration and Wi-Fi survive.
+
+Full (new or wiped boards): write the whole factory image at 0x0, the same
+as the factory flash_all.bat. This erases NVS: pairing and OTA registration
+are lost.
+"""
+
+from __future__ import annotations
+
+import enum
+from dataclasses import dataclass, field
+from pathlib import Path
+
+from .image import PT_OFFSET, PT_SIZE, FirmwareImage
+
+BAUD = "460800"
+
+
+class Mode(str, enum.Enum):
+    APP_ONLY = "app_only"
+    FULL = "full"
+
+
+@dataclass
+class Step:
+    kind: str                  # "backup" | "read_pt" | "write"
+    title: str
+    args: list[str]            # esptool arguments (no interpreter prefix)
+    est_s: int                 # rough duration for the UI
+    output: Path | None = None # file produced by the step (backup / table)
+
+
+@dataclass
+class Plan:
+    mode: Mode
+    image: FirmwareImage
+    port: str
+    steps: list[Step] = field(default_factory=list)
+    workdir: Path | None = None
+
+    def summary(self) -> list[str]:
+        return [f"{i}. {s.title} (~{_dur(s.est_s)})" for i, s in enumerate(self.steps, 1)]
+
+
+def _dur(s: int) -> str:
+    return f"{s // 60} min" if s >= 90 else f"{s} s"
+
+
+def _common(port: str, after: str) -> list[str]:
+    return ["--chip", "esp32s3", "--port", port, "--baud", BAUD,
+            "--before", "default_reset", "--after", after]
+
+
+def build_plan(image: FirmwareImage, mode: Mode, port: str, workdir: Path,
+               backup_to: Path | None = None) -> Plan:
+    workdir.mkdir(parents=True, exist_ok=True)
+    plan = Plan(mode, image, port, workdir=workdir)
+    if backup_to is not None:
+        size = {"4MB": "0x400000", "8MB": "0x800000", "16MB": "0x1000000"}.get(image.flash_size, "0x800000")
+        plan.steps.append(Step(
+            "backup", f"Back up the box's complete flash to {backup_to.name}",
+            _common(port, "no_reset") + ["read_flash", "0", size, str(backup_to)],
+            est_s=200 if size == "0x800000" else 100, output=backup_to))
+
+    write_opts = ["write_flash", "--flash_mode", "keep", "--flash_freq", "keep", "--flash_size", "keep"]
+    if mode == Mode.APP_ONLY:
+        pt_file = workdir / "box_partition_table.bin"
+        plan.steps.append(Step(
+            "read_pt", "Check the box has the same partition layout",
+            _common(port, "no_reset") + ["read_flash", hex(PT_OFFSET), hex(PT_SIZE), str(pt_file)],
+            est_s=5, output=pt_file))
+        app_file = workdir / "app_ota0.bin"
+        ota_file = workdir / "otadata_blank.bin"
+        app_file.write_bytes(image.app_bytes())
+        ota_file.write_bytes(image.blank_otadata())
+        otadata, ota0 = image.partition("otadata"), image.partition("ota_0")
+        plan.steps.append(Step(
+            "write", "Write the firmware app (keeps pairing, OTA registration, settings)",
+            _common(port, "hard_reset") + write_opts + [
+                hex(otadata.offset), str(ota_file), hex(ota0.offset), str(app_file)],
+            est_s=20))
+    else:
+        if image.kind != "merged":
+            raise ValueError("Full mode needs a complete image (bootloader + partition table + app); "
+                             "this file contains the app only - use App-only mode.")
+        plan.steps.append(Step(
+            "write", "Write the complete image (erases pairing and OTA registration)",
+            _common(port, "hard_reset") + write_opts + ["0x0", str(image.path)],
+            est_s=25))
+    return plan
+
+
+def check_partition_table(box_table: bytes, image: FirmwareImage) -> str | None:
+    """None if App-only is safe, otherwise the reason it is not."""
+    if box_table.strip(b"\xff") == b"":
+        return "The box has no partition table (blank or erased chip). Use Full mode."
+    if box_table != image.partition_table:
+        return ("The box uses a different partition layout than this image. "
+                "App-only could leave it unbootable - use Full mode.")
+    return None

kota_tech/flash/runner.py

@@ -0,0 +1,118 @@
+"""Runs a flash plan: one esptool subprocess per step, in a background thread.
+
+A subprocess (instead of calling esptool in-process) keeps esptool's
+stdout/sys.exit handling away from the GUI and lets the tool read progress
+line by line. Callbacks are invoked from the worker thread.
+"""
+
+from __future__ import annotations
+
+import re
+import subprocess
+import sys
+import threading
+from collections.abc import Callable
+from dataclasses import dataclass
+
+from .plan import Plan, check_partition_table
+
+_PROGRESS = re.compile(r"\((\d{1,3}) ?%\)")
+
+# esptool output -> technician-facing hint
+HINTS = [
+    (re.compile(r"could not open port|Access is denied|PermissionError|Resource busy", re.I),
+     "The USB port is in use. Close other programs that use the sensorbox port (serial monitors, Arduino IDE) and try again."),
+    (re.compile(r"Failed to connect to ESP32-S3|No serial data received|Wrong boot mode", re.I),
+     "The box did not enter flashing mode by itself. Open the case, hold the BOOT button, press and release RESET, "
+     "release BOOT, then press Start again."),
+    (re.compile(r"device reports readiness to read but returned no data|The port disappeared|device disconnected", re.I),
+     "The USB connection dropped. Use a short data-capable USB cable directly on the laptop (no hub) and try again."),
+    (re.compile(r"Invalid head of packet|timed out", re.I),
+     "Communication errors. Try another USB cable or port."),
+]
+
+
+@dataclass
+class Result:
+    ok: bool
+    message: str
+    hint: str = ""
+    failed_step: int | None = None
+
+
+class FlashRunner:
+    def __init__(self, plan: Plan,
+                 on_step: Callable[[int, str], None],
+                 on_progress: Callable[[int], None],
+                 on_output: Callable[[str], None],
+                 on_done: Callable[[Result], None],
+                 esptool_cmd: list[str] | None = None):
+        self.plan = plan
+        self._on_step, self._on_progress = on_step, on_progress
+        self._on_output, self._on_done = on_output, on_done
+        self._cmd = esptool_cmd or [sys.executable, "-m", "esptool"]
+        self._thread: threading.Thread | None = None
+
+    def start(self) -> None:
+        self._thread = threading.Thread(target=self._run, name="flash", daemon=True)
+        self._thread.start()
+
+    def join(self, timeout: float | None = None) -> None:
+        if self._thread:
+            self._thread.join(timeout)
+
+    def _run(self) -> None:
+        try:
+            self._on_done(self._execute())
+        except Exception as exc:  # never leave the UI waiting
+            self._on_done(Result(False, f"Internal error: {exc}"))
+
+    def _execute(self) -> Result:
+        for i, step in enumerate(self.plan.steps):
+            self._on_step(i, step.title)
+            self._on_progress(0)
+            code, output = self._esptool(step.args)
+            if code != 0:
+                return Result(False, f"Step {i + 1} failed: {step.title}", _hint(output), i)
+            if step.kind == "read_pt":
+                problem = check_partition_table(step.output.read_bytes(), self.plan.image)
+                if problem:
+                    return Result(False, problem, failed_step=i)
+            self._on_progress(100)
+        return Result(True, "Firmware written and verified by esptool.")
+
+    def _esptool(self, args: list[str]) -> tuple[int, str]:
+        cmd = self._cmd + args
+        self._on_output("$ esptool " + " ".join(args))
+        flags = subprocess.CREATE_NO_WINDOW if sys.platform == "win32" else 0
+        proc = subprocess.Popen(cmd, stdout=subprocess.PIPE, stderr=subprocess.STDOUT,
+                                creationflags=flags)
+        collected: list[str] = []
+        buf = b""
+        assert proc.stdout is not None
+        while chunk := proc.stdout.read1(4096):   # returns as soon as bytes arrive
+            buf += chunk
+            # esptool redraws progress with '\r'; treat it as a line break.
+            *lines, buf = re.split(rb"[\r\n]", buf)
+            for raw in lines:
+                self._line(raw, collected)
+        if buf:
+            self._line(buf, collected)
+        return proc.wait(), "\n".join(collected)
+
+    def _line(self, raw: bytes, collected: list[str]) -> None:
+        text = raw.decode("utf-8", "replace").strip()
+        if not text:
+            return
+        collected.append(text)
+        if m := _PROGRESS.search(text):
+            self._on_progress(min(int(m.group(1)), 100))
+            return   # progress lines are not worth listing one by one
+        self._on_output(text)
+
+
+def _hint(output: str) -> str:
+    for pattern, hint in HINTS:
+        if pattern.search(output):
+            return hint
+    return "See the esptool output below. Save it and send it to the firmware team if the problem repeats."

kota_tech/matter/payload.py

@@ -0,0 +1,96 @@
+"""Matter onboarding payloads: the "MT:..." QR string and the 11-digit manual code.
+
+Implements the Matter spec (5.1.3 QR payload, 5.1.4 manual pairing code):
+bit fields packed LSB-first, Base38 in 3-byte chunks, Verhoeff check digit.
+
+The sensorbox firmware uses the Matter SDK example commissionable data
+(CONFIG_EXAMPLE_COMMISSIONABLE_DATA_PROVIDER): every v1.0 box advertises
+VID 0xFFF1 / PID 0x8000 / discriminator 3840 with passcode 20202021, which is
+exactly the sticker (QR "MT:Y.K9042C00KA0648G00", manual 3497-011-2332).
+VID/PID/discriminator are taken from the box's own log when available; the
+passcode is never logged, so the known default is used.
+"""
+
+from __future__ import annotations
+
+import re
+from dataclasses import dataclass
+
+BASE38 = "0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZ-."
+RENDEZVOUS_BLE = 1 << 1
+DEFAULT_PASSCODE = 20202021          # Matter SDK test passcode used by the v1.0 firmware
+DEFAULT = dict(vendor_id=0xFFF1, product_id=0x8000, discriminator=3840)
+
+# chip[DIS]: Advertise commission parameter vendorID=65521 productID=32768 discriminator=3840/15 cm=1 cp=0
+_ADVERTISE = re.compile(r"vendorID=(\d+) productID=(\d+) discriminator=(\d+)")
+
+
+@dataclass(frozen=True)
+class SetupPayload:
+    vendor_id: int = DEFAULT["vendor_id"]
+    product_id: int = DEFAULT["product_id"]
+    discriminator: int = DEFAULT["discriminator"]
+    passcode: int = DEFAULT_PASSCODE
+    rendezvous: int = RENDEZVOUS_BLE
+    flow: int = 0                     # standard commissioning flow
+    version: int = 0
+    from_log: bool = False            # VID/PID/discriminator read from this box's log
+
+    def qr_text(self) -> str:
+        fields = [(self.version, 3), (self.vendor_id, 16), (self.product_id, 16), (self.flow, 2),
+                  (self.rendezvous, 8), (self.discriminator, 12), (self.passcode, 27), (0, 4)]
+        value, shift = 0, 0
+        for v, bits in fields:
+            if not 0 <= v < (1 << bits):
+                raise ValueError(f"field value {v} does not fit in {bits} bits")
+            value |= v << shift
+            shift += bits
+        return "MT:" + _base38(value.to_bytes(shift // 8, "little"))
+
+    def manual_code(self) -> str:
+        short = self.discriminator >> 8                       # upper 4 bits
+        chunk1 = short >> 2                                   # vid_pid_present = 0
+        chunk2 = ((short & 0x3) << 14) | (self.passcode & 0x3FFF)
+        chunk3 = self.passcode >> 14
+        digits = f"{chunk1}{chunk2:05d}{chunk3:04d}"
+        return digits + str(verhoeff_check(digits))
+
+    def manual_code_pretty(self) -> str:
+        c = self.manual_code()
+        return f"{c[:4]}-{c[4:7]}-{c[7:]}"
+
+
+def _base38(data: bytes) -> str:
+    out = []
+    for i in range(0, len(data), 3):
+        chunk = data[i:i + 3]
+        value = int.from_bytes(chunk, "little")
+        for _ in range({3: 5, 2: 4, 1: 2}[len(chunk)]):
+            value, rem = divmod(value, 38)
+            out.append(BASE38[rem])
+    return "".join(out)
+
+
+_D = [[0, 1, 2, 3, 4, 5, 6, 7, 8, 9], [1, 2, 3, 4, 0, 6, 7, 8, 9, 5], [2, 3, 4, 0, 1, 7, 8, 9, 5, 6],
+      [3, 4, 0, 1, 2, 8, 9, 5, 6, 7], [4, 0, 1, 2, 3, 9, 5, 6, 7, 8], [5, 9, 8, 7, 6, 0, 4, 3, 2, 1],
+      [6, 5, 9, 8, 7, 1, 0, 4, 3, 2], [7, 6, 5, 9, 8, 2, 1, 0, 4, 3], [8, 7, 6, 5, 9, 3, 2, 1, 0, 4],
+      [9, 8, 7, 6, 5, 4, 3, 2, 1, 0]]
+_P = [[0, 1, 2, 3, 4, 5, 6, 7, 8, 9], [1, 5, 7, 6, 2, 8, 3, 0, 9, 4], [5, 8, 0, 3, 7, 9, 6, 1, 4, 2],
+      [8, 9, 1, 6, 0, 4, 3, 5, 2, 7], [9, 4, 5, 3, 1, 2, 6, 8, 7, 0], [4, 2, 8, 6, 5, 7, 3, 9, 0, 1],
+      [2, 7, 9, 3, 8, 0, 6, 4, 1, 5], [7, 0, 4, 6, 9, 1, 3, 2, 5, 8]]
+_INV = [0, 4, 3, 2, 1, 5, 6, 7, 8, 9]
+
+
+def verhoeff_check(digits: str) -> int:
+    c = 0
+    for i, d in enumerate(reversed(digits)):
+        c = _D[c][_P[(i + 1) % 8][int(d)]]
+    return _INV[c]
+
+
+def payload_from_log(lines: list[str]) -> SetupPayload:
+    """Use the box's advertised VID/PID/discriminator if seen; defaults otherwise."""
+    for text in reversed(lines):
+        if m := _ADVERTISE.search(text):
+            return SetupPayload(int(m.group(1)), int(m.group(2)), int(m.group(3)), from_log=True)
+    return SetupPayload()

kota_tech/sd/disks.py

@@ -0,0 +1,128 @@
+"""Find SD cards (removable disks) on Windows and macOS.
+
+Safety first: only USB/SD/MMC-attached disks that are not the system or
+boot disk and not larger than MAX_CARD_BYTES are ever offered. Parsers are
+pure functions over the OS tool output so they can be tested without
+hardware.
+"""
+
+from __future__ import annotations
+
+import json
+import plistlib
+import subprocess
+import sys
+from dataclasses import dataclass, field
+
+MAX_CARD_BYTES = 256 * 1024**3         # larger "removable" disks are probably not SD cards
+CARD_BUSES = {"USB", "SD", "MMC"}
+
+
+@dataclass
+class Volume:
+    mount: str           # "E:\\" on Windows, "/Volumes/KOTA" on macOS ("" if not mounted)
+    filesystem: str      # "FAT32", "exFAT", "MS-DOS FAT32", ...
+    label: str
+
+
+@dataclass
+class Disk:
+    id: str              # Windows disk number / macOS "/dev/disk4"
+    name: str
+    size: int
+    bus: str
+    volumes: list[Volume] = field(default_factory=list)
+    has_media: bool = True
+
+    @property
+    def size_text(self) -> str:
+        return f"{self.size / 1e9:.1f} GB" if self.size else "no card"
+
+    @property
+    def label(self) -> str:
+        vols = ", ".join(f"{v.mount or '-'} {v.filesystem} '{v.label}'" for v in self.volumes) or "no volume"
+        return f"Disk {self.id}: {self.name} - {self.size_text} ({self.bus}) - {vols}"
+
+
+# ------------------------------------------------------------------ Windows
+
+WIN_LIST_PS = r"""
+$ErrorActionPreference = 'SilentlyContinue'
+# Filter by bus BEFORE touching partitions: querying volumes of every
+# internal disk made this take >30 s on a machine with several HDDs.
+$out = @(Get-Disk | Where-Object { -not $_.IsSystem -and -not $_.IsBoot -and
+                                   @('USB','SD','MMC') -contains [string]$_.BusType } | ForEach-Object {
+  $d = $_
+  $vols = @(Get-Partition -DiskNumber $d.Number | ForEach-Object {
+      $v = $_ | Get-Volume
+      [pscustomobject]@{ DriveLetter = [string]$_.DriveLetter; FileSystem = [string]$v.FileSystem; Label = [string]$v.FileSystemLabel }
+  })
+  [pscustomobject]@{ Number = $d.Number; FriendlyName = $d.FriendlyName; Size = [int64]$d.Size;
+                     BusType = [string]$d.BusType; Volumes = $vols }
+})
+ConvertTo-Json -InputObject $out -Depth 4 -Compress
+"""
+
+
+def parse_windows(json_text: str) -> list[Disk]:
+    data = json.loads(json_text or "[]")
+    if isinstance(data, dict):     # ConvertTo-Json quirk for one element
+        data = [data]
+    disks = []
+    for d in data:
+        if str(d.get("BusType")) not in CARD_BUSES:
+            continue
+        vols = d.get("Volumes") or []
+        if isinstance(vols, dict):
+            vols = [vols]
+        volumes = [Volume(f"{v['DriveLetter']}:\\" if v.get("DriveLetter") and v["DriveLetter"] not in ("\x00", "") else "",
+                          v.get("FileSystem") or "", v.get("Label") or "") for v in vols]
+        size = int(d.get("Size") or 0)
+        disks.append(Disk(str(d["Number"]), d.get("FriendlyName") or "Disk", size, str(d["BusType"]),
+                          [v for v in volumes if v.mount or v.filesystem], has_media=size > 0))
+    return disks
+
+
+# -------------------------------------------------------------------- macOS
+
+def parse_macos(list_plist: bytes, infos: dict[str, bytes]) -> list[Disk]:
+    """`diskutil list -plist physical` + `diskutil info -plist <disk>` for each."""
+    listing = plistlib.loads(list_plist)
+    disks = []
+    for entry in listing.get("AllDisksAndPartitions", []):
+        ident = entry.get("DeviceIdentifier", "")
+        info = plistlib.loads(infos[ident]) if ident in infos else {}
+        protocol = str(info.get("BusProtocol", ""))
+        removable = bool(info.get("RemovableMedia") or info.get("Removable") or info.get("Ejectable"))
+        internal = bool(info.get("Internal", True))
+        is_root = any(p.get("MountPoint") == "/" for p in entry.get("Partitions", []) + entry.get("APFSVolumes", []))
+        if ident == "disk0" or is_root or not (removable or not internal or protocol in ("USB", "Secure Digital", "SD")):
+            continue
+        vols = [Volume(p.get("MountPoint", ""), p.get("Content", ""), p.get("VolumeName", ""))
+                for p in entry.get("Partitions", [])]
+        size = int(entry.get("Size") or info.get("TotalSize") or 0)
+        bus = "SD" if "Secure Digital" in protocol or protocol == "SD" else (protocol or "USB")
+        disks.append(Disk(f"/dev/{ident}", info.get("MediaName", "Disk"), size, bus, vols, has_media=size > 0))
+    return disks
+
+
+# ------------------------------------------------------------------ public
+
+def list_cards() -> tuple[list[Disk], list[Disk]]:
+    """(cards that may be formatted, readers/disks shown but not offered)."""
+    if sys.platform == "win32":
+        # Driver-level listing (milliseconds, 1.5 s worst case) instead of
+        # Get-Disk/WMI, which stalled 5-21 s on an empty card-reader slot.
+        from .win_disks import list_disks
+        disks = list_disks(CARD_BUSES)
+    elif sys.platform == "darwin":
+        lst = subprocess.run(["diskutil", "list", "-plist", "physical"], capture_output=True, timeout=30).stdout
+        infos = {}
+        for e in plistlib.loads(lst).get("AllDisksAndPartitions", []):
+            ident = e.get("DeviceIdentifier", "")
+            infos[ident] = subprocess.run(["diskutil", "info", "-plist", ident], capture_output=True, timeout=30).stdout
+        disks = parse_macos(lst, infos)
+    else:
+        return [], []
+    ok = [d for d in disks if d.has_media and 0 < d.size <= MAX_CARD_BYTES]
+    return ok, [d for d in disks if d not in ok]

kota_tech/sd/envfile.py

@@ -0,0 +1,151 @@
+"""ENV.TXT for the sensorbox SD card.
+
+Parsing mirrors EnvironmentService::read_env_var in the firmware exactly:
+lines read with a 512-byte buffer, split at the FIRST '=', key compared
+verbatim (no trimming), CR/LF removed from the value only, first match wins.
+So the checks below report what would actually break a box - e.g. a UTF-8
+BOM (Windows Notepad) hides the first key, and "KEY = value" is not "KEY".
+
+The firmware FAT driver has no long-file-name support: the file must be
+the 8.3 name ENV.TXT (case-insensitive) in the card root.
+"""
+
+from __future__ import annotations
+
+import re
+from dataclasses import dataclass
+from pathlib import Path
+
+ENV_NAME = "ENV.TXT"
+BUFFER_NAME = "BUFFER.TXT"          # offline measurements waiting for upload
+LINE_BUF = 512                      # char line[512] in the firmware
+REQUIRED = ("INFLUX_URL", "INFLUX_TOKEN")
+OPTIONAL = ("SSID", "PASSWORD")
+_BOM = b"\xef\xbb\xbf"
+
+
+@dataclass
+class Issue:
+    level: str          # "error" | "warning" | "info"
+    text: str
+
+
+@dataclass
+class EnvConfig:
+    influx_url: str = ""
+    influx_token: str = ""
+    ssid: str = ""
+    password: str = ""
+
+    @property
+    def local_wifi(self) -> bool:
+        return bool(self.ssid or self.password)
+
+    def lines(self) -> list[tuple[str, str]]:
+        out = [("INFLUX_TOKEN", self.influx_token), ("INFLUX_URL", self.influx_url)]
+        if self.local_wifi:
+            out += [("SSID", self.ssid), ("PASSWORD", self.password)]
+        return out
+
+    def render(self) -> bytes:
+        # LF only, no BOM, no quoting: exactly what the firmware parser expects.
+        return "".join(f"{k}={v}\n" for k, v in self.lines()).encode("utf-8")
+
+    def problems(self) -> list[Issue]:
+        issues: list[Issue] = []
+        for key, value in self.lines():
+            if any(c in value for c in "\r\n"):
+                issues.append(Issue("error", f"{key} contains a line break."))
+            if value != value.strip():
+                issues.append(Issue("error", f"{key} starts or ends with a space; the box would use the space too."))
+            if len(f"{key}={value}".encode()) >= LINE_BUF - 1:
+                issues.append(Issue("error", f"{key} is too long for the box (max {LINE_BUF - 2} bytes per line)."))
+        url = self.influx_url.strip()
+        if not url:
+            issues.append(Issue("error", "INFLUX_URL is empty."))
+        elif not re.match(r"^https?://", url):
+            issues.append(Issue("error", "INFLUX_URL must start with https://"))
+        elif not ("/api/v2/write" in url and "bucket=" in url and "org=" in url):
+            issues.append(Issue("error", "INFLUX_URL must be a write URL: .../api/v2/write?bucket=...&org=..."))
+        elif url.startswith("http://"):
+            issues.append(Issue("warning", "INFLUX_URL uses http:// (unencrypted)."))
+        if not self.influx_token:
+            issues.append(Issue("error", "INFLUX_TOKEN is empty."))
+        elif re.search(r"\s", self.influx_token):
+            issues.append(Issue("error", "INFLUX_TOKEN contains spaces."))
+        elif len(self.influx_token) < 20:
+            issues.append(Issue("warning", "INFLUX_TOKEN looks too short."))
+        if self.local_wifi:
+            if not self.ssid or not self.password:
+                issues.append(Issue("error", "Wi-Fi needs both SSID and PASSWORD (the box ignores one without the other)."))
+            if len(self.ssid.encode()) > 32:
+                issues.append(Issue("error", "SSID is longer than 32 bytes."))
+            pw = self.password
+            if pw and not (8 <= len(pw) <= 63 or re.fullmatch(r"[0-9A-Fa-f]{64}", pw)):
+                issues.append(Issue("error", "Wi-Fi PASSWORD must be 8-63 characters (WPA2)."))
+        return issues
+
+
+@dataclass
+class EnvCheck:
+    values: dict[str, str]
+    issues: list[Issue]
+
+    @property
+    def ok(self) -> bool:
+        return not any(i.level == "error" for i in self.issues)
+
+    def masked(self) -> dict[str, str]:
+        out = {}
+        for k, v in self.values.items():
+            out[k] = (v[:4] + "..." + v[-4:] if len(v) > 12 else "***") if k in ("INFLUX_TOKEN", "PASSWORD") else v
+        return out
+
+
+def parse_env(raw: bytes) -> EnvCheck:
+    """Read ENV.TXT the way the firmware does and report what it would see."""
+    issues: list[Issue] = []
+    if raw.startswith(_BOM):
+        issues.append(Issue("error", "File starts with a UTF-8 BOM (saved by Notepad?): the box cannot read the first key. "
+                                     "Re-write the card with the tool."))
+    text = raw.decode("utf-8", errors="replace")
+    values: dict[str, str] = {}
+    for n, line in enumerate(text.split("\n"), 1):
+        if len(line.encode()) >= LINE_BUF - 1:
+            issues.append(Issue("error", f"Line {n} is longer than the box can read."))
+        if "=" not in line:
+            continue
+        key, value = line.split("=", 1)
+        value = value.replace("\r", "")
+        if key != key.strip():
+            issues.append(Issue("error", f"Line {n}: spaces around the key '{key.strip()}' - the box will not find it."))
+        if key in values:
+            issues.append(Issue("warning", f"{key} appears twice; the box uses the first one."))
+            continue
+        values[key] = value
+    for key in REQUIRED:
+        if key not in values:
+            issues.append(Issue("error", f"{key} is missing - the box stops at start-up (white LED)."))
+        elif not values[key]:
+            issues.append(Issue("error", f"{key} is empty."))
+    if values.get("HTTP_SERVER") == "true":
+        issues.append(Issue("warning", "HTTP_SERVER=true: a box with newer firmware starts in Wi-Fi setup mode."))
+    if bool(values.get("SSID")) != bool(values.get("PASSWORD")):
+        issues.append(Issue("warning", "Only one of SSID / PASSWORD is set; the box ignores Wi-Fi settings."))
+    elif values.get("SSID"):
+        issues.append(Issue("info", "Wi-Fi settings present: newer firmware uses this Wi-Fi instead of Matter "
+                                    "(the factory v1.0 firmware ignores them)."))
+    return EnvCheck(values, issues)
+
+
+def load_template(path: Path) -> EnvConfig:
+    """Settings from an existing ENV.TXT (e.g. 002-SD_card_format/ENV.txt)."""
+    v = parse_env(path.read_bytes()).values
+    return EnvConfig(v.get("INFLUX_URL", ""), v.get("INFLUX_TOKEN", ""), v.get("SSID", ""), v.get("PASSWORD", ""))
+
+
+def find_case_insensitive(root: Path, name: str) -> Path | None:
+    for p in root.iterdir() if root.is_dir() else ():
+        if p.is_file() and p.name.lower() == name.lower():
+            return p
+    return None

kota_tech/sd/fat32.py

@@ -0,0 +1,135 @@
+"""FAT32 + MBR layout for an SD card, as raw byte writes (no OS formatter).
+
+Follows the Microsoft FAT specification (fatgen103): BPB at sector 0,
+FSInfo at 1, backup boot sector at 6, two FATs, root directory in cluster 2
+holding the volume label. Cluster sizes follow Windows' defaults. The
+partition starts at 1 MiB (SD erase-block friendly), MBR type 0x0C
+(FAT32 LBA), which is what the firmware's FatFs expects.
+
+Pure functions: the result is a list of (offset, bytes) writes plus zero
+ranges relative to the start of the DISK, so it can be tested on a buffer.
+"""
+
+from __future__ import annotations
+
+import math
+import struct
+from dataclasses import dataclass
+
+PART_START = 1024 * 1024
+FAT32_MAX_BYTES = 32 * 1024**3        # Windows convention, and all the box needs
+MIN_CLUSTERS, MAX_CLUSTERS = 65525, 0x0FFFFFF5
+RESERVED = 32
+NUM_FATS = 2
+MEDIA = 0xF8
+
+
+@dataclass(frozen=True)
+class Fat32Layout:
+    bytes_per_sector: int
+    part_start: int            # bytes from disk start
+    part_sectors: int
+    sectors_per_cluster: int
+    fat_sectors: int
+    clusters: int
+
+    @property
+    def data_start(self) -> int:      # sectors from partition start
+        return RESERVED + NUM_FATS * self.fat_sectors
+
+
+def _spc(sectors: int, bps: int) -> int:
+    size = sectors * bps
+    for limit, cluster in ((260 * 1024**2, 512), (8 * 1024**3, 4096), (16 * 1024**3, 8192),
+                           (32 * 1024**3, 16384)):
+        if size <= limit:
+            return max(1, cluster // bps)
+    return max(1, 32768 // bps)
+
+
+def plan(disk_bytes: int, bps: int = 512) -> Fat32Layout:
+    part_bytes = min(disk_bytes - PART_START, FAT32_MAX_BYTES)
+    part_bytes -= part_bytes % (1024 * 1024)                # whole MiB
+    sectors = part_bytes // bps
+    if sectors <= 0:
+        raise ValueError("card is too small")
+    spc = _spc(sectors, bps)
+    fat = 1
+    for _ in range(20):                                     # converge FAT size <-> cluster count
+        clusters = (sectors - RESERVED - NUM_FATS * fat) // spc
+        need = math.ceil((clusters + 2) * 4 / bps)
+        if need == fat:
+            break
+        fat = need
+    clusters = (sectors - RESERVED - NUM_FATS * fat) // spc
+    if not MIN_CLUSTERS <= clusters < MAX_CLUSTERS:
+        raise ValueError(f"card size gives {clusters} clusters - not valid for FAT32")
+    return Fat32Layout(bps, PART_START, sectors, spc, fat, clusters)
+
+
+def _boot_sector(lay: Fat32Layout, label: bytes, vol_id: int) -> bytes:
+    bps = lay.bytes_per_sector
+    b = bytearray(bps)
+    b[0:3] = b"\xEB\x58\x90"
+    b[3:11] = b"MSWIN4.1"
+    struct.pack_into("<HBHBHHBHHHII", b, 11, bps, lay.sectors_per_cluster, RESERVED, NUM_FATS, 0, 0,
+                     MEDIA, 0, 63, 255, lay.part_start // bps, lay.part_sectors)
+    struct.pack_into("<IHHIHH", b, 36, lay.fat_sectors, 0, 0, 2, 1, 6)
+    struct.pack_into("<BBBI", b, 64, 0x80, 0, 0x29, vol_id)
+    b[71:82] = label
+    b[82:90] = b"FAT32   "
+    b[90:93] = b"\xF4\xEB\xFD"                              # not bootable: hlt loop
+    b[510:512] = b"\x55\xAA"
+    return bytes(b)
+
+
+def _fsinfo(lay: Fat32Layout) -> bytes:
+    b = bytearray(lay.bytes_per_sector)
+    struct.pack_into("<I", b, 0, 0x41615252)
+    struct.pack_into("<III", b, 484, 0x61417272, lay.clusters - 1, 3)   # root uses cluster 2
+    struct.pack_into("<I", b, 508, 0xAA550000)
+    return bytes(b)
+
+
+def mbr(lay: Fat32Layout, signature: int) -> bytes:
+    b = bytearray(512)
+    struct.pack_into("<I", b, 0x1B8, signature)
+    entry = struct.pack("<B3sB3sII", 0x00, b"\xFE\xFF\xFF", 0x0C, b"\xFE\xFF\xFF",
+                        lay.part_start // lay.bytes_per_sector, lay.part_sectors)
+    b[0x1BE:0x1BE + 16] = entry
+    b[510:512] = b"\x55\xAA"
+    return bytes(b[:512]) + bytes(lay.bytes_per_sector - 512)
+
+
+def volume_label(text: str) -> bytes:
+    label = text.upper().encode("ascii", "replace")[:11]
+    return label.ljust(11, b" ")
+
+
+def build(lay: Fat32Layout, label: str, vol_id: int, disk_signature: int,
+          disk_bytes: int) -> tuple[list[tuple[int, int]], list[tuple[int, bytes]]]:
+    """(zero ranges, writes) in disk byte offsets; apply zero ranges first."""
+    bps, p = lay.bytes_per_sector, lay.part_start
+    lab = volume_label(label)
+    fat_bytes = lay.fat_sectors * bps
+    fat1 = p + RESERVED * bps
+    fat2 = fat1 + fat_bytes
+    root = p + lay.data_start * bps
+    cluster = lay.sectors_per_cluster * bps
+    zeros = [
+        (0, PART_START),                                   # old MBR / GPT header and gap
+        (disk_bytes - PART_START, PART_START),             # backup GPT at the end of the disk
+        (p, RESERVED * bps),                               # reserved region
+        (fat1, NUM_FATS * fat_bytes),                      # both FATs
+        (root, cluster),                                   # root directory cluster
+    ]
+    boot, info = _boot_sector(lay, lab, vol_id), _fsinfo(lay)
+    first_fat = struct.pack("<III", 0x0FFFFF00 | MEDIA, 0x0FFFFFFF, 0x0FFFFFFF)
+    label_entry = lab + bytes([0x08]) + bytes(20)          # 32-byte volume-label directory entry
+    writes = [
+        (p, boot), (p + bps, info), (p + 6 * bps, boot), (p + 7 * bps, info),
+        (fat1, first_fat), (fat2, first_fat),
+        (root, label_entry),
+        (0, mbr(lay, disk_signature)),                     # last: the partition appears only now
+    ]
+    return zeros, writes

kota_tech/sd/provision.py

@@ -0,0 +1,260 @@
+"""Format an SD card for the sensorbox and write / check ENV.TXT.
+
+Card format required by the firmware: MBR partition table, FAT32 (its FAT
+driver has no exFAT and no long file names), ENV.TXT in the root.
+
+Windows: formatting needs administrator rights, so kota_tech.sd.win_format
+runs elevated (UAC prompt). It re-checks the disk (number, size, bus, not the
+Windows drive) right before erasing it, so a card swapped after the
+technician confirmed is not touched, and it writes MBR + FAT32 itself
+(no Storage cmdlets, which stalled on empty card-reader slots). Larger cards
+get a 32 GB FAT32 partition (Windows convention; plenty for the box).
+macOS: `diskutil eraseDisk FAT32 KOTA MBRFormat` (same as format_sd.sh).
+"""
+
+from __future__ import annotations
+
+import json
+import os
+import plistlib
+import subprocess
+import sys
+import time
+import uuid
+from dataclasses import dataclass, field
+from pathlib import Path
+
+from .disks import Disk
+from .envfile import BUFFER_NAME, ENV_NAME, EnvCheck, EnvConfig, find_case_insensitive, parse_env
+
+VOLUME_LABEL = "KOTA"
+
+
+@dataclass
+class Outcome:
+    ok: bool
+    message: str
+    mount: str = ""
+    log: list[str] = field(default_factory=list)
+
+
+@dataclass
+class CardReport:
+    mount: str
+    filesystem: str
+    env: EnvCheck | None
+    buffered_lines: int | None      # measurements waiting on the card for upload
+    problems: list[str]
+
+
+# ----------------------------------------------------------------- Windows
+
+WORK_ROOT = Path.home() / "KotaTechnicianTool" / "tmp"
+
+
+def _workdir() -> Path:
+    # Not tempfile.mkdtemp(): on Windows it creates an owner-only folder, and a
+    # file written there by the ELEVATED script is then unreadable for this
+    # (non-elevated) process. A normally inherited ACL works for both.
+    work = WORK_ROOT / f"sd_{uuid.uuid4().hex[:10]}"
+    work.mkdir(parents=True, exist_ok=False)
+    return work
+
+
+def win_format_command(disk: Disk, result: Path) -> tuple[str, str, str]:
+    """(program, parameters, working dir) for the elevated helper."""
+    root = Path(__file__).resolve().parents[2]            # the version folder holding kota_tech/
+    params = f'-m kota_tech.sd.win_format --disk {int(disk.id)} --size {int(disk.size)} ' \
+             f'--label {VOLUME_LABEL} --result "{result}"'
+    return sys.executable, params, str(root)
+
+
+def _run_elevated(program: str, params: str, cwd: str, timeout_s: int = 300) -> int | None:
+    """ShellExecuteEx 'runas' + wait. None if the technician refused the UAC prompt."""
+    import ctypes
+    from ctypes import wintypes
+
+    class SHELLEXECUTEINFOW(ctypes.Structure):
+        _fields_ = [("cbSize", wintypes.DWORD), ("fMask", ctypes.c_ulong), ("hwnd", wintypes.HWND),
+                    ("lpVerb", wintypes.LPCWSTR), ("lpFile", wintypes.LPCWSTR), ("lpParameters", wintypes.LPCWSTR),
+                    ("lpDirectory", wintypes.LPCWSTR), ("nShow", ctypes.c_int), ("hInstApp", wintypes.HINSTANCE),
+                    ("lpIDList", ctypes.c_void_p), ("lpClass", wintypes.LPCWSTR), ("hkeyClass", wintypes.HKEY),
+                    ("dwHotKey", wintypes.DWORD), ("hIconOrMonitor", wintypes.HANDLE), ("hProcess", wintypes.HANDLE)]
+
+    SEE_MASK_NOCLOSEPROCESS, SW_HIDE = 0x40, 0
+    info = SHELLEXECUTEINFOW(cbSize=ctypes.sizeof(SHELLEXECUTEINFOW), fMask=SEE_MASK_NOCLOSEPROCESS,
+                             lpVerb="runas", lpFile=program, lpParameters=params, lpDirectory=cwd, nShow=SW_HIDE)
+    shell32 = ctypes.WinDLL("shell32", use_last_error=True)
+    k32 = ctypes.WinDLL("kernel32", use_last_error=True)
+    if not shell32.ShellExecuteExW(ctypes.byref(info)):
+        return None                                            # ERROR_CANCELLED (1223) or failure
+    k32.WaitForSingleObject(info.hProcess, timeout_s * 1000)
+    code = wintypes.DWORD()
+    k32.GetExitCodeProcess(info.hProcess, ctypes.byref(code))
+    k32.CloseHandle(info.hProcess)
+    return code.value
+
+
+def _format_windows(disk: Disk, log: list[str]) -> Outcome:
+    result = _workdir() / "result.json"
+    log.append("Asking Windows for administrator rights to format the card (UAC prompt)...")
+    t = time.perf_counter()
+    code = _run_elevated(*win_format_command(disk, result))
+    if code is None:
+        return Outcome(False, "Administrator permission was refused - the card was not formatted.", log=log)
+    try:
+        res = json.loads(result.read_text(encoding="utf-8"))
+    except (OSError, ValueError) as exc:
+        return Outcome(False, f"The formatter did not report back ({exc.__class__.__name__}, exit {code}). "
+                              "Check the card with 'Check card'.", log=log)
+    steps = ", ".join(f"{k} {v:.1f} s" for k, v in res.get("timings", {}).items())
+    log.append(f"{res.get('message', '')} ({time.perf_counter() - t:.1f} s incl. permission prompt; {steps})")
+    return Outcome(bool(res.get("ok")), res.get("message", ""), res.get("drive", ""), log)
+
+
+def _eject_windows(mount: str) -> bool:
+    """Flush, lock, dismount and eject the card - what 'Safely Remove' does.
+
+    Not Shell.Application InvokeVerb('Eject'): it fails silently because the
+    verb is named 'E&ject' (and is localised on non-English Windows).
+    """
+    import ctypes
+    from ctypes import wintypes
+
+    k32 = ctypes.WinDLL("kernel32", use_last_error=True)
+    k32.CreateFileW.restype = wintypes.HANDLE
+    k32.CreateFileW.argtypes = [wintypes.LPCWSTR, wintypes.DWORD, wintypes.DWORD, wintypes.LPVOID,
+                                wintypes.DWORD, wintypes.DWORD, wintypes.HANDLE]
+    k32.DeviceIoControl.argtypes = [wintypes.HANDLE, wintypes.DWORD, wintypes.LPVOID, wintypes.DWORD,
+                                    wintypes.LPVOID, wintypes.DWORD, ctypes.POINTER(wintypes.DWORD), wintypes.LPVOID]
+    GENERIC_RW, SHARE_RW, OPEN_EXISTING = 0xC0000000, 0x3, 3
+    FSCTL_LOCK_VOLUME, FSCTL_DISMOUNT_VOLUME = 0x00090018, 0x00090020
+    IOCTL_STORAGE_MEDIA_REMOVAL, IOCTL_STORAGE_EJECT_MEDIA = 0x002D4804, 0x002D4808
+    handle = k32.CreateFileW(f"\\\\.\\{mount[0]}:", GENERIC_RW, SHARE_RW, None, OPEN_EXISTING, 0, None)
+    if handle in (None, wintypes.HANDLE(-1).value):
+        return False
+    ret = wintypes.DWORD()
+
+    def ioctl(code: int, buf=None, size: int = 0) -> bool:
+        return bool(k32.DeviceIoControl(handle, code, buf, size, None, 0, ctypes.byref(ret), None))
+
+    try:
+        k32.FlushFileBuffers(handle)
+        for _ in range(10):                       # Explorer/indexer may hold it briefly
+            if ioctl(FSCTL_LOCK_VOLUME):
+                break
+            time.sleep(0.5)
+        else:
+            return False
+        if not ioctl(FSCTL_DISMOUNT_VOLUME):
+            return False
+        allow = ctypes.c_bool(False)              # PREVENT_MEDIA_REMOVAL{FALSE}
+        ioctl(IOCTL_STORAGE_MEDIA_REMOVAL, ctypes.byref(allow), 1)
+        ioctl(IOCTL_STORAGE_EJECT_MEDIA)          # card readers may not support it; dismount suffices
+        return True
+    finally:
+        k32.CloseHandle(handle)
+
+
+# ------------------------------------------------------------------- macOS
+
+def _format_macos(disk: Disk, log: list[str]) -> Outcome:
+    log.append(f"diskutil eraseDisk FAT32 {VOLUME_LABEL} MBRFormat {disk.id}")
+    proc = subprocess.run(["diskutil", "eraseDisk", "FAT32", VOLUME_LABEL, "MBRFormat", disk.id],
+                          capture_output=True, text=True, timeout=600)
+    log += [l for l in proc.stdout.splitlines() if l.strip()]
+    if proc.returncode != 0:
+        return Outcome(False, "Formatting failed: " + (proc.stderr.strip() or proc.stdout.strip()[-200:])
+                       + " (is the card's write-protect switch on?)", log=log)
+    part = f"{disk.id}s1"
+    for _ in range(20):   # wait for the volume to mount
+        info = plistlib.loads(subprocess.run(["diskutil", "info", "-plist", part], capture_output=True).stdout or b"<plist><dict/></plist>")
+        if info.get("MountPoint"):
+            return Outcome(True, "Formatted FAT32 (MBR).", info["MountPoint"], log)
+        time.sleep(0.5)
+    return Outcome(False, "Formatted, but the card did not mount.", log=log)
+
+
+def _eject_macos(disk_id: str) -> bool:
+    return subprocess.run(["diskutil", "eject", disk_id], capture_output=True, timeout=60).returncode == 0
+
+
+# ------------------------------------------------------------------ common
+
+def write_env(mount: str, env: EnvConfig) -> Outcome:
+    """Write ENV.TXT (8.3 name, LF, no BOM), keep other files (buffered data), read back."""
+    problems = [i.text for i in env.problems() if i.level == "error"]
+    if problems:
+        return Outcome(False, "Settings are not valid: " + " ".join(problems))
+    root = Path(mount)
+    if not root.is_dir():
+        return Outcome(False, f"Card not found at {mount}.")
+    old = find_case_insensitive(root, ENV_NAME)
+    if old is not None and old.name != ENV_NAME:
+        old.unlink()                                   # replace env.txt / Env.txt variants
+    target = root / ENV_NAME
+    data = env.render()
+    with open(target, "wb") as fh:
+        fh.write(data)
+        fh.flush()
+        os.fsync(fh.fileno())
+    if target.read_bytes() != data:
+        return Outcome(False, "ENV.TXT read-back does not match - the card may be faulty.")
+    check = parse_env(target.read_bytes())
+    if not check.ok:
+        return Outcome(False, "ENV.TXT was written but does not validate: "
+                       + " ".join(i.text for i in check.issues if i.level == "error"))
+    return Outcome(True, f"ENV.TXT written and verified on {mount}.", mount)
+
+
+def format_and_write(disk: Disk, env: EnvConfig, eject_card: bool = True) -> Outcome:
+    problems = [i.text for i in env.problems() if i.level == "error"]
+    if problems:
+        return Outcome(False, "Settings are not valid: " + " ".join(problems))
+    log: list[str] = []
+    if sys.platform == "win32":
+        fmt = _format_windows(disk, log)
+    elif sys.platform == "darwin":
+        fmt = _format_macos(disk, log)
+    else:
+        return Outcome(False, "SD provisioning is supported on Windows and macOS only.")
+    if not fmt.ok:
+        return fmt
+    wr = write_env(fmt.mount, env)
+    log.append(wr.message)
+    if not wr.ok:
+        return Outcome(False, wr.message, fmt.mount, log)
+    if eject_card:
+        log.append("Card ejected - you can remove it." if eject(fmt.mount, disk) else
+                   "Could not eject the card automatically - use 'Safely remove' before pulling it out.")
+    return Outcome(True, "Card ready: formatted FAT32 and ENV.TXT verified.", fmt.mount, log)
+
+
+def eject(mount: str, disk: Disk | None = None) -> bool:
+    """True if the card was dismounted and can be pulled out safely."""
+    if sys.platform == "win32":
+        return _eject_windows(mount)
+    if sys.platform == "darwin" and disk is not None:
+        return _eject_macos(disk.id)
+    return False
+
+
+def check_card(mount: str, filesystem: str = "") -> CardReport:
+    """What the box would find on this card (values masked in the UI)."""
+    root = Path(mount)
+    problems: list[str] = []
+    fs = filesystem.upper()
+    if fs and "FAT32" not in fs and fs not in ("FAT", "MS-DOS FAT32", "MSDOS"):
+        problems.append(f"File system is {filesystem}; the box needs FAT32 - re-format the card.")
+    env_file = find_case_insensitive(root, ENV_NAME)
+    env = parse_env(env_file.read_bytes()) if env_file else None
+    if env_file is None:
+        problems.append("No ENV.TXT on the card - the box stops at start-up (white LED).")
+    elif len(env_file.name.split(".")[0]) > 8:
+        problems.append("ENV.TXT has a long name variant; use exactly ENV.TXT.")
+    buf = find_case_insensitive(root, BUFFER_NAME)
+    lines = None
+    if buf is not None:
+        with open(buf, "rb") as fh:
+            lines = sum(1 for ln in fh if ln.strip())
+    return CardReport(mount, filesystem, env, lines, problems)

kota_tech/sd/win_disks.py

@@ -0,0 +1,161 @@
+"""Fast Windows card discovery straight from the storage drivers (ctypes).
+
+Why not Get-Disk / WMI: every fresh PowerShell/WMI query enumerates ALL
+disks, which wakes sleeping hard drives - measured 1.6 to 21 s per listing
+on a PC with two SATA HDDs, freezing the UI each time. Here each physical
+drive is opened with access 0 (no admin needed, no I/O to the medium) and
+only its cached device descriptor is read; size and volumes are queried only
+for USB/SD/MMC disks. A full listing takes milliseconds.
+"""
+
+from __future__ import annotations
+
+import concurrent.futures
+import ctypes
+import string
+from ctypes import wintypes
+
+from .disks import Disk, Volume
+
+IOCTL_STORAGE_QUERY_PROPERTY = 0x002D1400
+IOCTL_STORAGE_GET_DEVICE_NUMBER = 0x002D1080
+IOCTL_DISK_GET_DRIVE_GEOMETRY_EX = 0x000700A0
+BUS_TYPES = {1: "SCSI", 2: "ATAPI", 3: "ATA", 4: "1394", 7: "USB", 8: "RAID", 10: "SAS", 11: "SATA",
+             12: "SD", 13: "MMC", 14: "Virtual", 15: "FileBackedVirtual", 17: "NVMe", 18: "SCM", 19: "UFS"}
+SHARE_RW, OPEN_EXISTING = 0x3, 3
+DRIVE_REMOVABLE, DRIVE_FIXED = 2, 3
+MAX_DRIVES = 32
+
+_k32 = ctypes.WinDLL("kernel32", use_last_error=True)
+_k32.CreateFileW.restype = wintypes.HANDLE
+_k32.CreateFileW.argtypes = [wintypes.LPCWSTR, wintypes.DWORD, wintypes.DWORD, wintypes.LPVOID,
+                             wintypes.DWORD, wintypes.DWORD, wintypes.HANDLE]
+_k32.DeviceIoControl.argtypes = [wintypes.HANDLE, wintypes.DWORD, wintypes.LPVOID, wintypes.DWORD,
+                                 wintypes.LPVOID, wintypes.DWORD, ctypes.POINTER(wintypes.DWORD), wintypes.LPVOID]
+_k32.GetDriveTypeW.argtypes = [wintypes.LPCWSTR]
+_k32.GetVolumeInformationW.argtypes = [wintypes.LPCWSTR, wintypes.LPWSTR, wintypes.DWORD,
+                                       ctypes.POINTER(wintypes.DWORD), ctypes.POINTER(wintypes.DWORD),
+                                       ctypes.POINTER(wintypes.DWORD), wintypes.LPWSTR, wintypes.DWORD]
+_INVALID = wintypes.HANDLE(-1).value
+
+
+class _Query(ctypes.Structure):          # STORAGE_PROPERTY_QUERY (StorageDeviceProperty, standard)
+    _fields_ = [("PropertyId", wintypes.DWORD), ("QueryType", wintypes.DWORD), ("Extra", ctypes.c_ubyte * 4)]
+
+
+class _DevNumber(ctypes.Structure):      # STORAGE_DEVICE_NUMBER
+    _fields_ = [("DeviceType", wintypes.DWORD), ("DeviceNumber", wintypes.DWORD),
+                ("PartitionNumber", wintypes.DWORD)]
+
+
+def _open(path: str):
+    h = _k32.CreateFileW(path, 0, SHARE_RW, None, OPEN_EXISTING, 0, None)
+    return None if h in (None, _INVALID) else h
+
+
+def _ioctl(h, code: int, inbuf=None, insize: int = 0, outsize: int = 1024) -> bytes | None:
+    out = ctypes.create_string_buffer(outsize)
+    got = wintypes.DWORD()
+    ok = _k32.DeviceIoControl(h, code, inbuf, insize, out, outsize, ctypes.byref(got), None)
+    return out.raw[:got.value] if ok else None
+
+
+def _descriptor(h) -> tuple[str, str] | None:
+    """(bus, "vendor product") from STORAGE_DEVICE_DESCRIPTOR - served from the driver's cache."""
+    q = _Query(0, 0)
+    raw = _ioctl(h, IOCTL_STORAGE_QUERY_PROPERTY, ctypes.byref(q), ctypes.sizeof(q))
+    if not raw or len(raw) < 32:
+        return None
+    vendor_off, product_off = int.from_bytes(raw[12:16], "little"), int.from_bytes(raw[16:20], "little")
+    bus = int.from_bytes(raw[28:32], "little")
+
+    def text(off: int) -> str:
+        if not off or off >= len(raw):
+            return ""
+        return raw[off:].split(b"\0", 1)[0].decode("ascii", "replace").strip()
+
+    return BUS_TYPES.get(bus, f"bus{bus}"), " ".join(t for t in (text(vendor_off), text(product_off)) if t) or "Disk"
+
+
+def _size(h) -> int:
+    raw = _ioctl(h, IOCTL_DISK_GET_DRIVE_GEOMETRY_EX, outsize=256)   # fails when no card is inserted
+    return int.from_bytes(raw[24:32], "little") if raw and len(raw) >= 32 else 0
+
+
+def _volumes_by_disk() -> dict[int, list[Volume]]:
+    found: dict[int, list[Volume]] = {}
+    mask = _k32.GetLogicalDrives()
+    for i, letter in enumerate(string.ascii_uppercase):
+        if not mask & (1 << i) or _k32.GetDriveTypeW(f"{letter}:\\") not in (DRIVE_REMOVABLE, DRIVE_FIXED):
+            continue
+        h = _open(f"\\\\.\\{letter}:")
+        if h is None:
+            continue
+        try:
+            raw = _ioctl(h, IOCTL_STORAGE_GET_DEVICE_NUMBER, outsize=ctypes.sizeof(_DevNumber))
+        finally:
+            _k32.CloseHandle(h)
+        if raw and len(raw) >= 8:
+            num = int.from_bytes(raw[4:8], "little")
+            found.setdefault(num, []).append(Volume(f"{letter}:\\", "", ""))
+    return found
+
+
+def _fill_volume_info(v: Volume) -> None:
+    name, fs = ctypes.create_unicode_buffer(64), ctypes.create_unicode_buffer(32)
+    serial, maxlen, flags = wintypes.DWORD(), wintypes.DWORD(), wintypes.DWORD()
+    if _k32.GetVolumeInformationW(v.mount, name, 64, ctypes.byref(serial), ctypes.byref(maxlen),
+                                  ctypes.byref(flags), fs, 32):
+        v.filesystem, v.label = fs.value, name.value
+
+
+MEDIA_TIMEOUT_S = 1.5
+# Slot queries still running from an earlier listing (an empty card-reader
+# slot can block ~13 s on its first media query). Never start a second one.
+_pending: dict[int, concurrent.futures.Future] = {}
+_pool = concurrent.futures.ThreadPoolExecutor(max_workers=8, thread_name_prefix="sd-media")
+
+
+def _media_size(n: int) -> int:
+    h = _open(f"\\\\.\\PhysicalDrive{n}")
+    if h is None:
+        return 0
+    try:
+        return _size(h)
+    finally:
+        _k32.CloseHandle(h)
+
+
+def list_disks(buses: set[str]) -> list[Disk]:
+    """Disks on the given buses (e.g. {"USB", "SD", "MMC"}), with size and volumes.
+
+    Media queries run in parallel with a short timeout: a slot that does not
+    answer in time is reported as "no card" instead of freezing the caller.
+    """
+    candidates: list[tuple[int, tuple[str, str]]] = []
+    for n in range(MAX_DRIVES):
+        h = _open(f"\\\\.\\PhysicalDrive{n}")
+        if h is None:
+            continue
+        try:
+            desc = _descriptor(h)
+        finally:
+            _k32.CloseHandle(h)
+        if desc is not None and desc[0] in buses:   # internal disks: only the cached descriptor is read
+            candidates.append((n, desc))
+    for n, _ in candidates:
+        if n not in _pending or _pending[n].done():
+            _pending[n] = _pool.submit(_media_size, n)
+    concurrent.futures.wait([_pending[n] for n, _ in candidates], timeout=MEDIA_TIMEOUT_S)
+    volumes: dict[int, list[Volume]] | None = None
+    disks = []
+    for n, (bus, name) in candidates:
+        fut = _pending[n]
+        size = fut.result() if fut.done() and fut.exception() is None else 0
+        if size and volumes is None:
+            volumes = _volumes_by_disk()
+        vols = (volumes or {}).get(n, []) if size else []
+        for v in vols:
+            _fill_volume_info(v)
+        disks.append(Disk(str(n), name, size, bus, vols, has_media=size > 0))
+    return disks

kota_tech/sd/win_format.py

@@ -0,0 +1,192 @@
+"""Elevated Windows SD-card formatter (runs as: python -m kota_tech.sd.win_format ...).
+
+Replaces Clear-Disk / New-Partition / Format-Volume: every Storage cmdlet
+goes through the storage provider, which stalls ~13 s on an empty card
+reader slot, several times per format. This helper touches only the chosen
+disk through its own driver:
+
+  1. guard: bus is USB/SD/MMC, size is exactly the one the technician
+     confirmed, and the disk does not hold the Windows drive;
+  2. lock + dismount the card's volumes;
+  3. raw writes: zero old MBR/GPT, FAT32 structures (kota_tech.sd.fat32),
+     then the new MBR last;
+  4. unlock, let Windows re-read the disk, wait for the FAT32 'KOTA' volume;
+  5. read-only `chkdsk` of the new volume.
+
+The result (with per-step timings) goes to a JSON file for the non-elevated
+tool, which then writes ENV.TXT through the normal file API.
+"""
+
+from __future__ import annotations
+
+import argparse
+import ctypes
+import json
+import os
+import random
+import subprocess
+import sys
+import time
+from ctypes import wintypes
+
+from . import fat32, win_disks
+
+GENERIC_RW, SHARE_RW, OPEN_EXISTING = 0xC0000000, 0x3, 3
+FSCTL_LOCK_VOLUME, FSCTL_UNLOCK_VOLUME, FSCTL_DISMOUNT_VOLUME = 0x00090018, 0x0009001C, 0x00090020
+IOCTL_DISK_UPDATE_PROPERTIES = 0x00070140
+CARD_BUSES = {"USB", "SD", "MMC"}
+CHUNK = 1024 * 1024
+
+k32 = win_disks._k32
+k32.WriteFile.argtypes = [wintypes.HANDLE, wintypes.LPCVOID, wintypes.DWORD,
+                          ctypes.POINTER(wintypes.DWORD), wintypes.LPVOID]
+k32.SetFilePointerEx.argtypes = [wintypes.HANDLE, ctypes.c_longlong, ctypes.POINTER(ctypes.c_longlong), wintypes.DWORD]
+k32.VirtualAlloc.restype = wintypes.LPVOID
+k32.VirtualAlloc.argtypes = [wintypes.LPVOID, ctypes.c_size_t, wintypes.DWORD, wintypes.DWORD]
+
+
+class FormatError(RuntimeError):
+    pass
+
+
+def _open_rw(path: str):
+    h = k32.CreateFileW(path, GENERIC_RW, SHARE_RW, None, OPEN_EXISTING, 0, None)
+    if h in (None, win_disks._INVALID):
+        raise FormatError(f"cannot open {path} (error {ctypes.get_last_error()})")
+    return h
+
+
+def _ioctl(h, code: int) -> bool:
+    got = wintypes.DWORD()
+    return bool(k32.DeviceIoControl(h, code, None, 0, None, 0, ctypes.byref(got), None))
+
+
+class RawDisk:
+    """Sector-aligned writes through a page-aligned buffer (device alignment rules)."""
+
+    def __init__(self, number: int, bps: int):
+        self.h = _open_rw(rf"\\.\PhysicalDrive{number}")
+        self.bps = bps
+        self.buf = k32.VirtualAlloc(None, CHUNK, 0x3000, 0x04)      # MEM_COMMIT|RESERVE, RW
+
+    def write(self, offset: int, data: bytes) -> None:
+        if offset % self.bps or len(data) % self.bps:
+            raise FormatError("unaligned write")
+        pos = 0
+        while pos < len(data):
+            n = min(CHUNK, len(data) - pos)
+            ctypes.memmove(self.buf, data[pos:pos + n], n)
+            self._raw(offset + pos, n)
+            pos += n
+
+    def zero(self, offset: int, length: int) -> None:
+        ctypes.memset(self.buf, 0, CHUNK)
+        pos = 0
+        while pos < length:
+            n = min(CHUNK, length - pos)
+            self._raw(offset + pos, n)
+            pos += n
+
+    def _raw(self, offset: int, n: int) -> None:
+        if not k32.SetFilePointerEx(self.h, offset, None, 0):
+            raise FormatError(f"seek failed (error {ctypes.get_last_error()})")
+        done = wintypes.DWORD()
+        if not k32.WriteFile(self.h, self.buf, n, ctypes.byref(done), None) or done.value != n:
+            raise FormatError(f"write at {offset} failed (error {ctypes.get_last_error()}) - write-protected card?")
+
+    def close(self) -> None:
+        k32.FlushFileBuffers(self.h)
+        _ioctl(self.h, IOCTL_DISK_UPDATE_PROPERTIES)                 # re-read the new partition table
+        k32.CloseHandle(self.h)
+
+
+def format_card(number: int, expected_size: int, label: str, timings: dict) -> str:
+    t0 = time.perf_counter()
+    disk = next((d for d in win_disks.list_disks(CARD_BUSES) if d.id == str(number)), None)
+    if disk is None:
+        raise FormatError("Refusing: the disk is not a USB/SD/MMC card reader.")
+    if disk.size != expected_size:
+        raise FormatError("Refusing: the disk changed since it was selected (card swapped?).")
+    system = os.environ.get("SystemDrive", "C:").upper().rstrip("\\") + "\\"
+    if any(v.mount.upper() == system for v in disk.volumes):
+        raise FormatError("Refusing: this disk holds the Windows drive.")
+    timings["guard"] = time.perf_counter() - t0
+
+    t = time.perf_counter()
+    locked = []
+    for v in disk.volumes:
+        h = _open_rw(rf"\\.\{v.mount[0]}:")
+        for _ in range(20):
+            if _ioctl(h, FSCTL_LOCK_VOLUME):
+                break
+            time.sleep(0.25)
+        else:
+            k32.CloseHandle(h)
+            raise FormatError(f"{v.mount} is in use by another program - close it and try again.")
+        _ioctl(h, FSCTL_DISMOUNT_VOLUME)
+        locked.append(h)
+    timings["lock_volumes"] = time.perf_counter() - t
+
+    t = time.perf_counter()
+    lay = fat32.plan(disk.size)
+    zeros, writes = fat32.build(lay, label, random.getrandbits(32), random.getrandbits(32), disk.size)
+    raw = RawDisk(number, lay.bytes_per_sector)
+    try:
+        for off, n in zeros:
+            raw.zero(off, n)
+        for off, data in writes:                       # MBR is last: the partition appears complete
+            raw.write(off, data)
+    finally:
+        for h in locked:
+            _ioctl(h, FSCTL_UNLOCK_VOLUME)
+            k32.CloseHandle(h)
+        raw.close()
+    timings["write"] = time.perf_counter() - t
+
+    t = time.perf_counter()
+    drive = ""
+    for _ in range(80):                                # Windows mounts the new volume by itself
+        d = next((x for x in win_disks.list_disks(CARD_BUSES) if x.id == str(number)), None)
+        vol = next((v for v in (d.volumes if d else []) if v.filesystem.upper() == "FAT32"), None)
+        if vol and vol.label.upper() == label.upper():
+            drive = vol.mount
+            break
+        time.sleep(0.25)
+    timings["mount"] = time.perf_counter() - t
+    if not drive:
+        raise FormatError("Formatted, but Windows did not mount the card - remove and re-insert it.")
+
+    t = time.perf_counter()
+    chk = subprocess.run(["chkdsk", drive.rstrip("\\")], capture_output=True, text=True, timeout=120,
+                         creationflags=subprocess.CREATE_NO_WINDOW)
+    timings["chkdsk"] = time.perf_counter() - t
+    if chk.returncode != 0:
+        tail = " ".join(chk.stdout.split()[-30:])
+        raise FormatError(f"chkdsk reported problems on the new file system: {tail}")
+    return drive
+
+
+def main(argv: list[str] | None = None) -> int:
+    ap = argparse.ArgumentParser()
+    ap.add_argument("--disk", type=int, required=True)
+    ap.add_argument("--size", type=int, required=True)
+    ap.add_argument("--label", default="KOTA")
+    ap.add_argument("--result", required=True)
+    a = ap.parse_args(argv)
+    timings: dict[str, float] = {}
+    result = {"ok": False, "message": "", "drive": "", "timings": timings}
+    try:
+        result["drive"] = format_card(a.disk, a.size, a.label, timings)
+        result["ok"] = True
+        result["message"] = "Formatted FAT32 (MBR), checked with chkdsk."
+    except FormatError as exc:
+        result["message"] = str(exc)
+    except Exception as exc:                            # report everything to the tool
+        result["message"] = f"Unexpected error: {exc!r}"
+    with open(a.result, "w", encoding="utf-8") as fh:
+        json.dump(result, fh)
+    return 0 if result["ok"] else 1
+
+
+if __name__ == "__main__":
+    sys.exit(main())

kota_tech/service/report.py

@@ -0,0 +1,101 @@
+"""Hand-off of a diagnosis to the KOTA service system (Google Apps Script).
+
+The tool opens the box's service page in the technician's browser:
+    <base><MAC>#kota-report=<base64url(JSON)>
+The service page (v1.1.0+) reads the fragment and pre-fills status and note;
+the technician checks it, adds the location and saves - so the report is
+authored by their own Google login and the tool holds no credentials.
+The fragment is never sent to any server (redirect host or Apps Script).
+"""
+
+from __future__ import annotations
+
+import base64
+import json
+import re
+
+from .. import __version__
+from ..diag.engine import Report, Severity
+
+DEFAULT_BASE = "https://service.kota-app.com/"
+NOTE_LIMIT = 4000        # the service form accepts 5000; leave room for the technician
+
+# Status names exactly as in the service system (Code.gs STATUSES).
+OK = "Działa poprawnie"
+CHECK = "Do sprawdzenia"
+IN_SERVICE = "W trakcie serwisu"
+HARDWARE = "Błąd hardware"
+SOFTWARE = "Błąd software"
+POWER = "Problem z zasilaniem"
+CONNECTIVITY = "Problem z łącznością"
+
+# Root-finding rule id prefix -> service status (first match wins).
+_STATUS_BY_RULE = [
+    ("reboot.brownout", POWER), ("reboot.power", POWER), ("tech.power.", POWER),
+    ("sys.crash", SOFTWARE), ("reboot.watchdog", SOFTWARE), ("sys.out_of_resources", SOFTWARE),
+    ("influx.bad_request", SOFTWARE), ("ota.selfcheck_failed", SOFTWARE), ("tech.quick.hung", SOFTWARE),
+    ("rtc.init_failed", HARDWARE), ("rtc.lost_after_sync", HARDWARE), ("i2c.", HARDWARE), ("sensor.", HARDWARE),
+    ("sd.", HARDWARE), ("sen66.", HARDWARE), ("bme688.", HARDWARE), ("as7341.", HARDWARE),
+    ("mic.read_fail", HARDWARE), ("mic.silent", HARDWARE), ("tech.rtc_i2c.", HARDWARE), ("tech.sensors.", HARDWARE),
+    ("tech.mic.mic_faulty", HARDWARE), ("tech.mic.mic_switch_faulty", HARDWARE), ("tech.white.sd_", HARDWARE),
+    ("matter.", CONNECTIVITY), ("net.", CONNECTIVITY), ("wifi.", CONNECTIVITY), ("influx.", CONNECTIVITY),
+    ("ota.", CONNECTIVITY), ("tech.network.", CONNECTIVITY),
+    ("rtc.clock_not_running", CHECK), ("reboot.", CHECK),
+]
+_MAC = re.compile(r"^[0-9A-F]{12}$")
+
+
+def normalize_mac(mac: str) -> str:
+    return re.sub(r"[^0-9A-Fa-f]", "", mac or "").upper()
+
+
+def service_status(report: Report) -> str:
+    """Suggested status; the technician can change it in the form."""
+    problems = [rc for rc in report.roots if rc.severity >= Severity.WARNING]
+    if not problems:
+        return OK if any(m == "data_uploaded" and t is not None for m, _, t in report.milestones) else CHECK
+    rid = problems[0].finding.rule_id
+    for prefix, status in _STATUS_BY_RULE:
+        if rid.startswith(prefix):
+            return status
+    return CHECK
+
+
+def service_note(report: Report, limit: int = NOTE_LIMIT) -> str:
+    lines = [f"[KOTA Technician Tool {__version__}] {report.verdict}",
+             f"Firmware: {report.firmware.describe()}",
+             f"Expected LED: {report.led.capitalize()}"]
+    reached = [label for _, label, t in report.milestones if t is not None]
+    missing = [label for _, label, t in report.milestones if t is None]
+    if reached:
+        lines.append("OK: " + ", ".join(reached))
+    if missing:
+        lines.append("Not reached: " + ", ".join(missing))
+    for rc in report.roots:
+        f = rc.finding
+        lines.append(f"- [{f.severity.label}] {f.title}")
+        for c in rc.consequences:
+            lines.append(f"    -> {c.title}")
+    if report.technician:
+        lines.append("Technician checks:")
+        lines += [f"  * {t}" for t in report.technician[-12:]]
+    text = "\n".join(lines)
+    return text if len(text) <= limit else text[:limit - 20].rstrip() + "\n...(shortened)"
+
+
+def report_url(mac: str, report: Report, base: str = DEFAULT_BASE) -> str:
+    mac = normalize_mac(mac)
+    if not _MAC.match(mac):
+        raise ValueError(f"not a box MAC address: {mac!r}")
+    payload = {"v": 1, "mac": mac, "status": service_status(report), "note": service_note(report),
+               "tool": f"v{__version__}"}
+    raw = json.dumps(payload, ensure_ascii=False, separators=(",", ":")).encode("utf-8")
+    frag = base64.urlsafe_b64encode(raw).decode("ascii").rstrip("=")
+    base = base if base.endswith("/") else base + "/"
+    return f"{base}{mac}#kota-report={frag}"
+
+
+def decode_fragment(url: str) -> dict:
+    """Inverse of report_url (used by tests and for troubleshooting)."""
+    frag = url.split("#kota-report=", 1)[1]
+    return json.loads(base64.urlsafe_b64decode(frag + "=" * (-len(frag) % 4)).decode("utf-8"))

kota_tech/ui/cheatsheet.py

@@ -40,7 +40,8 @@ HINTS = [
     "reboot name the cause.",
     "<b>Small LED next to the RGB LED</b> blinks once per second while the "
     "firmware runs. Not blinking = firmware hung or not running.",
-    "<b>Outside the case</b>: power switch and the Matter button. Holding the "
+    "<b>Outside the case</b> (back): power switch, the <b>microphone switch</b> just above it "
+    "(off = no noise measurements), and the Matter button. Holding the "
     "Matter button <b>5 s</b> factory-resets the box (it forgets its Matter "
     "network and must be commissioned again with the sticker QR code).",
     "<b>Inside the case</b> (unscrew): RESET and BOOT buttons and the SD card. "
@@ -55,7 +56,8 @@ STEPS = [
     "Open the <b>Serial monitor</b> tab, choose the sensorbox port, press "
     "<b>Connect</b>.",
     "Press <b>Reset &amp; capture</b> to record a full boot log from the first line.",
-    "Note the RGB LED colour and compare with the table below.",
+    "Read the <b>Diagnosis</b> panel on the right, then open <b>Guided troubleshooting</b> "
+    "and start <b>Quick check</b>: the tool asks what you see and checks the log live.",
 ]
 
 

kota_tech/ui/diag_panel.py

@@ -1,230 +1,234 @@
-"""Diagnostics side panel: renders a diag.engine.Report.
+"""Diagnostics side panel: renders a diag.engine.Report.
-
+
-Layout: verdict banner, expected LED, firmware, start-up milestones, a
+Layout: verdict banner, expected LED, firmware, start-up milestones, a
-findings tree (root causes; their consequences as children; titles only)
+findings tree (root causes; their consequences as children; titles only)
-and a wrapped detail pane for the selected finding.
+and a wrapped detail pane for the selected finding.
-"""
+"""
-
+
-from __future__ import annotations
+from __future__ import annotations
-
+
-from PySide6.QtCore import Qt
+from PySide6.QtCore import Qt
-from PySide6.QtGui import QBrush, QColor
+from PySide6.QtGui import QBrush, QColor
-from PySide6.QtWidgets import (
+from PySide6.QtWidgets import (
-    QFrame,
+    QFrame,
-    QHBoxLayout,
+    QHBoxLayout,
-    QLabel,
+    QLabel,
-    QListWidget,
+    QListWidget,
-    QListWidgetItem,
+    QListWidgetItem,
-    QSizePolicy,
+    QPushButton,
-    QSplitter,
+    QSizePolicy,
-    QTextBrowser,
+    QSplitter,
-    QTreeWidget,
+    QTextBrowser,
-    QTreeWidgetItem,
+    QTreeWidget,
-    QVBoxLayout,
+    QTreeWidgetItem,
-    QWidget,
+    QVBoxLayout,
-)
+    QWidget,
-
+)
-from ..diag.engine import LED, Finding, Report, Severity
+
-
+from ..diag.engine import LED, Finding, Report, Severity
-SEV_COLOR = {
+
-    Severity.CRITICAL: "#b03a2e",
+SEV_COLOR = {
-    Severity.ERROR: "#d9534f",
+    Severity.CRITICAL: "#b03a2e",
-    Severity.WARNING: "#c77c02",
+    Severity.ERROR: "#d9534f",
-    Severity.INFO: "#2e6da4",
+    Severity.WARNING: "#c77c02",
-}
+    Severity.INFO: "#2e6da4",
-# verdict banner (background, text) by verdict severity; None = healthy
+}
-BANNER = {
+# verdict banner (background, text) by verdict severity; None = healthy
-    Severity.CRITICAL: ("#f6d5d1", "#7b1e14"),
+BANNER = {
-    Severity.ERROR: ("#f9dedc", "#8a2019"),
+    Severity.CRITICAL: ("#f6d5d1", "#7b1e14"),
-    Severity.WARNING: ("#fdebc8", "#6b4400"),
+    Severity.ERROR: ("#f9dedc", "#8a2019"),
-    None: ("#d8f0dd", "#1b5e2a"),
+    Severity.WARNING: ("#fdebc8", "#6b4400"),
-}
+    None: ("#d8f0dd", "#1b5e2a"),
-_KEY = Qt.ItemDataRole.UserRole
+}
-
+_KEY = Qt.ItemDataRole.UserRole
-
+
-def _heading(text: str) -> QLabel:
+
-    lbl = QLabel(text)
+def _heading(text: str) -> QLabel:
-    f = lbl.font()
+    lbl = QLabel(text)
-    f.setBold(True)
+    f = lbl.font()
-    lbl.setFont(f)
+    f.setBold(True)
-    return lbl
+    lbl.setFont(f)
-
+    return lbl
-
+
-def _esc(s: str) -> str:
+
-    return s.replace("&", "&amp;").replace("<", "&lt;").replace(">", "&gt;")
+def _esc(s: str) -> str:
-
+    return s.replace("&", "&amp;").replace("<", "&lt;").replace(">", "&gt;")
-
+
-class DiagnosticsPanel(QWidget):
+
-    def __init__(self, parent: QWidget | None = None):
+class DiagnosticsPanel(QWidget):
-        super().__init__(parent)
+    def __init__(self, parent: QWidget | None = None):
-        self.setMinimumWidth(380)
+        super().__init__(parent)
-
+        self.setMinimumWidth(380)
-        self.verdict = QLabel(wordWrap=True)
+
-        self.verdict.setMargin(10)
+        self.verdict = QLabel(wordWrap=True)
-        vf = self.verdict.font()
+        self.verdict.setMargin(10)
-        vf.setPointSize(vf.pointSize() + 2)
+        vf = self.verdict.font()
-        vf.setBold(True)
+        vf.setPointSize(vf.pointSize() + 2)
-        self.verdict.setFont(vf)
+        vf.setBold(True)
-
+        self.verdict.setFont(vf)
-        self.led_swatch = QLabel()
+
-        self.led_swatch.setFixedSize(22, 22)
+        self.led_swatch = QLabel()
-        self.led_text = QLabel(wordWrap=True)
+        self.led_swatch.setFixedSize(22, 22)
-        led_row = QHBoxLayout()
+        self.led_text = QLabel(wordWrap=True)
-        led_row.addWidget(self.led_swatch, 0, Qt.AlignmentFlag.AlignTop)
+        led_row = QHBoxLayout()
-        led_row.addWidget(self.led_text, 1)
+        led_row.addWidget(self.led_swatch, 0, Qt.AlignmentFlag.AlignTop)
-
+        led_row.addWidget(self.led_text, 1)
-        self.firmware = QLabel(wordWrap=True)
+
-        self.firmware.setTextInteractionFlags(Qt.TextInteractionFlag.TextSelectableByMouse)
+        self.firmware = QLabel(wordWrap=True)
-
+        self.firmware.setTextInteractionFlags(Qt.TextInteractionFlag.TextSelectableByMouse)
-        self.milestones = QListWidget()
+
-        self.milestones.setFrameShape(QFrame.Shape.NoFrame)
+        self.milestones = QListWidget()
-        self.milestones.setSelectionMode(QListWidget.SelectionMode.NoSelection)
+        self.milestones.setFrameShape(QFrame.Shape.NoFrame)
-        self.milestones.setSizePolicy(QSizePolicy.Policy.Preferred, QSizePolicy.Policy.Maximum)
+        self.milestones.setSelectionMode(QListWidget.SelectionMode.NoSelection)
-
+        self.milestones.setSizePolicy(QSizePolicy.Policy.Preferred, QSizePolicy.Policy.Maximum)
-        self.tree = QTreeWidget()
+
-        self.tree.setHeaderHidden(True)
+        self.tree = QTreeWidget()
-        self.tree.setIndentation(16)
+        self.tree.setHeaderHidden(True)
-        self.tree.setTextElideMode(Qt.TextElideMode.ElideRight)
+        self.tree.setIndentation(16)
-        self.detail = QTextBrowser()
+        self.tree.setTextElideMode(Qt.TextElideMode.ElideRight)
-        self.detail.setOpenExternalLinks(False)
+        self.detail = QTextBrowser()
-        findings = QSplitter(Qt.Orientation.Vertical)
+        self.detail.setOpenExternalLinks(False)
-        findings.addWidget(self.tree)
+        findings = QSplitter(Qt.Orientation.Vertical)
-        findings.addWidget(self.detail)
+        findings.addWidget(self.tree)
-        findings.setSizes([220, 260])
+        findings.addWidget(self.detail)
-
+        findings.setSizes([220, 260])
-        lay = QVBoxLayout(self)
+
-        lay.setContentsMargins(4, 0, 0, 0)
+        lay = QVBoxLayout(self)
-        lay.addWidget(self.verdict)
+        lay.setContentsMargins(4, 0, 0, 0)
-        lay.addWidget(_heading("Status LED should be"))
+        lay.addWidget(self.verdict)
-        lay.addLayout(led_row)
+        lay.addWidget(_heading("Status LED should be"))
-        lay.addWidget(_heading("Firmware"))
+        lay.addLayout(led_row)
-        lay.addWidget(self.firmware)
+        lay.addWidget(_heading("Firmware"))
-        lay.addWidget(_heading("Start-up progress (current boot)"))
+        lay.addWidget(self.firmware)
-        lay.addWidget(self.milestones)
+        self.qr_btn = QPushButton("Matter pairing QR code...")
-        lay.addWidget(_heading("Findings - root causes first; click one for details"))
+        self.qr_btn.setToolTip("Show the box's Matter QR code on screen to scan with the phone")
-        lay.addWidget(findings, 1)
+        lay.addWidget(self.qr_btn, 0, Qt.AlignmentFlag.AlignLeft)
-
+        lay.addWidget(_heading("Start-up progress (current boot)"))
-        self._findings: dict[str, Finding] = {}
+        lay.addWidget(self.milestones)
-        self._selected: str | None = None
+        lay.addWidget(_heading("Findings - root causes first; click one for details"))
-        # key -> expanded, chosen by the user; survives the rebuild on refresh.
+        lay.addWidget(findings, 1)
-        self._expanded: dict[str, bool] = {}
+
-        self.tree.currentItemChanged.connect(self._on_select)
+        self._findings: dict[str, Finding] = {}
-        self.tree.itemCollapsed.connect(lambda it: self._remember(it, False))
+        self._selected: str | None = None
-        self.tree.itemExpanded.connect(lambda it: self._remember(it, True))
+        # key -> expanded, chosen by the user; survives the rebuild on refresh.
-
+        self._expanded: dict[str, bool] = {}
-    # ------------------------------------------------------------------
+        self.tree.currentItemChanged.connect(self._on_select)
-    def show_report(self, r: Report) -> None:
+        self.tree.itemCollapsed.connect(lambda it: self._remember(it, False))
-        bg, fg = BANNER.get(r.verdict_severity, BANNER[Severity.WARNING])
+        self.tree.itemExpanded.connect(lambda it: self._remember(it, True))
-        if r.lines == 0:
+
-            bg, fg = "#e6e6e6", "#333333"
+    # ------------------------------------------------------------------
-        self.verdict.setText(r.verdict)
+    def show_report(self, r: Report) -> None:
-        self.verdict.setStyleSheet(f"QLabel {{ background:{bg}; color:{fg}; border-radius:6px; }}")
+        bg, fg = BANNER.get(r.verdict_severity, BANNER[Severity.WARNING])
-
+        if r.lines == 0:
-        name, colour = LED[r.led]
+            bg, fg = "#e6e6e6", "#333333"
-        self.led_swatch.setStyleSheet(
+        self.verdict.setText(r.verdict)
-            f"QLabel {{ background:{colour}; border:1px solid #777; border-radius:11px; }}")
+        self.verdict.setStyleSheet(f"QLabel {{ background:{bg}; color:{fg}; border-radius:6px; }}")
-        ask = "" if r.led == "UNKNOWN" else " - <i>check it matches the box</i>"
+
-        reason = f"<br><small style='color:#666'>from: {_esc(r.led_reason)}</small>" if r.led_reason else ""
+        name, colour = LED[r.led]
-        self.led_text.setText(f"<b>{name}</b>{ask}{reason}")
+        self.led_swatch.setStyleSheet(
-
+            f"QLabel {{ background:{colour}; border:1px solid #777; border-radius:11px; }}")
-        fw = r.firmware
+        ask = "" if r.led == "UNKNOWN" else " - <i>check it matches the box</i>"
-        sd = {True: "reads Wi-Fi settings from the SD card",
+        reason = f"<br><small style='color:#666'>from: {_esc(r.led_reason)}</small>" if r.led_reason else ""
-              False: "does not read Wi-Fi settings from the SD card",
+        self.led_text.setText(f"<b>{name}</b>{ask}{reason}")
-              None: "Wi-Fi-from-SD support unknown"}
+
-        self.firmware.setText(f"{_esc(fw.describe())}<br><small>{sd[fw.supports_sd_wifi]}</small>")
+        fw = r.firmware
-
+        sd = {True: "reads Wi-Fi settings from the SD card",
-        self.milestones.clear()
+              False: "does not read Wi-Fi settings from the SD card",
-        for _, label, t in r.milestones:
+              None: "Wi-Fi-from-SD support unknown"}
-            done = t is not None
+        self.firmware.setText(f"{_esc(fw.describe())}<br><small>{sd[fw.supports_sd_wifi]}</small>")
-            it = QListWidgetItem(("✔  " if done else "○  ") + label
+
-                                 + (f"   ({t / 1000:.1f} s)" if done else ""))
+        self.milestones.clear()
-            it.setForeground(QBrush(QColor("#1b7a33" if done else "#8a8a8a")))
+        for _, label, t in r.milestones:
-            self.milestones.addItem(it)
+            done = t is not None
-        rows = min(max(self.milestones.count(), 1), 15)
+            it = QListWidgetItem(("✔  " if done else "○  ") + label
-        self.milestones.setFixedHeight(rows * max(self.milestones.sizeHintForRow(0), 16) + 6)
+                                 + (f"   ({t / 1000:.1f} s)" if done else ""))
-
+            it.setForeground(QBrush(QColor("#1b7a33" if done else "#8a8a8a")))
-        self._fill_tree(r)
+            self.milestones.addItem(it)
-
+        rows = min(max(self.milestones.count(), 1), 15)
-    def _fill_tree(self, r: Report) -> None:
+        self.milestones.setFixedHeight(rows * max(self.milestones.sizeHintForRow(0), 16) + 6)
-        self.tree.blockSignals(True)
+
-        self.tree.clear()
+        self._fill_tree(r)
-        self._findings = {}
+
-        if not r.roots:
+    def _fill_tree(self, r: Report) -> None:
-            it = QTreeWidgetItem(["No problems detected in the log so far."])
+        self.tree.blockSignals(True)
-            it.setForeground(0, QBrush(QColor("#1b7a33")))
+        self.tree.clear()
-            self.tree.addTopLevelItem(it)
+        self._findings = {}
-        for rc in r.roots:
+        if not r.roots:
-            top = self._item(rc.finding, bold=True)
+            it = QTreeWidgetItem(["No problems detected in the log so far."])
-            self.tree.addTopLevelItem(top)
+            it.setForeground(0, QBrush(QColor("#1b7a33")))
-            for c in rc.consequences:
+            self.tree.addTopLevelItem(it)
-                top.addChild(self._item(c, prefix="↳ "))
+        for rc in r.roots:
-            top.setExpanded(self._expanded.get(rc.finding.key, True))
+            top = self._item(rc.finding, bold=True)
-        for title, key, items in (("Seen in earlier boots only", "grp:earlier", r.earlier),
+            self.tree.addTopLevelItem(top)
-                                  ("Resolved during this session", "grp:resolved", r.resolved)):
+            for c in rc.consequences:
-            if not items:
+                top.addChild(self._item(c, prefix="↳ "))
-                continue
+            top.setExpanded(self._expanded.get(rc.finding.key, True))
-            grp = QTreeWidgetItem([f"{title} ({len(items)})"])
+        for title, key, items in (("Seen in earlier boots only", "grp:earlier", r.earlier),
-            grp.setData(0, _KEY, key)
+                                  ("Resolved during this session", "grp:resolved", r.resolved)):
-            grp.setForeground(0, QBrush(QColor("#666666")))
+            if not items:
-            self.tree.addTopLevelItem(grp)
+                continue
-            for f in items:
+            grp = QTreeWidgetItem([f"{title} ({len(items)})"])
-                grp.addChild(self._item(f, prefix="✔ " if key == "grp:resolved" else ""))
+            grp.setData(0, _KEY, key)
-            grp.setExpanded(self._expanded.get(key, False))
+            grp.setForeground(0, QBrush(QColor("#666666")))
-        # Keep the selection across refreshes; default to the top root cause.
+            self.tree.addTopLevelItem(grp)
-        target = self._selected if self._selected in self._findings else (
+            for f in items:
-            r.roots[0].finding.key if r.roots else None)
+                grp.addChild(self._item(f, prefix="✔ " if key == "grp:resolved" else ""))
-        self.tree.blockSignals(False)
+            grp.setExpanded(self._expanded.get(key, False))
-        self._select(target)
+        # Keep the selection across refreshes; default to the top root cause.
-
+        target = self._selected if self._selected in self._findings else (
-    def _remember(self, item: QTreeWidgetItem, expanded: bool) -> None:
+            r.roots[0].finding.key if r.roots else None)
-        if key := item.data(0, _KEY):
+        self.tree.blockSignals(False)
-            self._expanded[key] = expanded
+        self._select(target)
-
+
-    def _item(self, f: Finding, prefix: str = "", bold: bool = False) -> QTreeWidgetItem:
+    def _remember(self, item: QTreeWidgetItem, expanded: bool) -> None:
-        it = QTreeWidgetItem([f"{prefix}[{f.severity.label}]  {f.title}"])
+        if key := item.data(0, _KEY):
-        it.setData(0, _KEY, f.key)
+            self._expanded[key] = expanded
-        it.setForeground(0, QBrush(QColor(SEV_COLOR.get(f.severity, "#333333"))))
+
-        it.setToolTip(0, f.title)
+    def _item(self, f: Finding, prefix: str = "", bold: bool = False) -> QTreeWidgetItem:
-        if bold:
+        it = QTreeWidgetItem([f"{prefix}[{f.severity.label}]  {f.title}"])
-            font = it.font(0)
+        it.setData(0, _KEY, f.key)
-            font.setBold(True)
+        it.setForeground(0, QBrush(QColor(SEV_COLOR.get(f.severity, "#333333"))))
-            it.setFont(0, font)
+        it.setToolTip(0, f.title)
-        self._findings[f.key] = f
+        if bold:
-        return it
+            font = it.font(0)
-
+            font.setBold(True)
-    def _select(self, key: str | None) -> None:
+            it.setFont(0, font)
-        if key is None:
+        self._findings[f.key] = f
-            self.detail.setHtml("<p style='color:#666'>Nothing to show yet.</p>")
+        return it
-            return
+
-        match = self.tree.findItems("*", Qt.MatchFlag.MatchWildcard | Qt.MatchFlag.MatchRecursive)
+    def _select(self, key: str | None) -> None:
-        for it in match:
+        if key is None:
-            if it.data(0, _KEY) == key:
+            self.detail.setHtml("<p style='color:#666'>Nothing to show yet.</p>")
-                self.tree.setCurrentItem(it)
+            return
-                return
+        match = self.tree.findItems("*", Qt.MatchFlag.MatchWildcard | Qt.MatchFlag.MatchRecursive)
-
+        for it in match:
-    def _on_select(self, cur: QTreeWidgetItem | None, _prev) -> None:
+            if it.data(0, _KEY) == key:
-        key = cur.data(0, _KEY) if cur else None
+                self.tree.setCurrentItem(it)
-        f = self._findings.get(key or "")
+                return
-        if f is None:
+
-            return
+    def _on_select(self, cur: QTreeWidgetItem | None, _prev) -> None:
-        self._selected = key
+        key = cur.data(0, _KEY) if cur else None
-        self.detail.setHtml(_detail_html(f))
+        f = self._findings.get(key or "")
-
+        if f is None:
-
+            return
-def _detail_html(f: Finding) -> str:
+        self._selected = key
-    colour = SEV_COLOR.get(f.severity, "#333")
+        self.detail.setHtml(_detail_html(f))
-    actions = "".join(f"<li>{_esc(a)}</li>" for a in f.actions)
+
-    seen = f"Seen {f.count}x"
+
-    if f.first_uptime_ms is not None:
+def _detail_html(f: Finding) -> str:
-        seen += f", first at {f.first_uptime_ms / 1000:.1f} s after start"
+    colour = SEV_COLOR.get(f.severity, "#333")
-    if f.resolved and f.resolved_by:
+    actions = "".join(f"<li>{_esc(a)}</li>" for a in f.actions)
-        seen += f" - resolved ({_esc(f.resolved_by)})"
+    seen = f"Seen {f.count}x"
-    evidence = "<br>".join(_esc(e) for e in f.evidence)
+    if f.first_uptime_ms is not None:
-    return (
+        seen += f", first at {f.first_uptime_ms / 1000:.1f} s after start"
-        f"<h3 style='color:{colour}; margin:0'>{_esc(f.title)}</h3>"
+    if f.resolved and f.resolved_by:
-        f"<p><b>What it means:</b> {_esc(f.meaning)}</p>"
+        seen += f" - resolved ({_esc(f.resolved_by)})"
-        + (f"<p><b>What to do:</b></p><ol>{actions}</ol>" if actions else "")
+    evidence = "<br>".join(_esc(e) for e in f.evidence)
-        + f"<p style='color:#666'>{seen}</p>"
+    return (
-        + (f"<p style='color:#555; font-family:Consolas,Menlo,monospace; font-size:9pt'>{evidence}</p>"
+        f"<h3 style='color:{colour}; margin:0'>{_esc(f.title)}</h3>"
-           if evidence else "")
+        f"<p><b>What it means:</b> {_esc(f.meaning)}</p>"
-    )
+        + (f"<p><b>What to do:</b></p><ol>{actions}</ol>" if actions else "")
+        + f"<p style='color:#666'>{seen}</p>"
+        + (f"<p style='color:#555; font-family:Consolas,Menlo,monospace; font-size:9pt'>{evidence}</p>"
+           if evidence else "")
+    )

kota_tech/ui/flash_tab.py

@@ -0,0 +1,398 @@
+"""Flash firmware tab: factory image or imported developer builds; App-only by default."""
+
+from __future__ import annotations
+
+import datetime as dt
+import tempfile
+from pathlib import Path
+
+from PySide6.QtCore import QObject, Qt, QTimer, Signal
+from PySide6.QtWidgets import (
+    QButtonGroup,
+    QCheckBox,
+    QFileDialog,
+    QInputDialog,
+    QComboBox,
+    QGroupBox,
+    QHBoxLayout,
+    QLabel,
+    QMessageBox,
+    QPlainTextEdit,
+    QProgressBar,
+    QPushButton,
+    QRadioButton,
+    QVBoxLayout,
+    QWidget,
+)
+
+from ..core.session import SESSIONS_DIR
+from ..flash.image import FirmwareImage, FirmwareLibrary, ImageError, bundled_images
+from ..flash.plan import Mode, build_plan
+from ..flash.runner import FlashRunner, Result
+from ..serialio.ports import PortInfo, list_serial_ports
+
+BACKUP_DIR = SESSIONS_DIR.parent / "backups"
+VERIFY_TIMEOUT_MS = 45_000
+
+HELP = (
+    "<b>If flashing cannot connect:</b> use a data-capable USB cable directly on the laptop, close "
+    "other programs using the port, then retry. Last resort (case must be opened): hold <b>BOOT</b>, "
+    "press and release <b>RESET</b>, release <b>BOOT</b>, and press Start again."
+)
+
+
+class _Bridge(QObject):
+    step = Signal(int, str)
+    progress = Signal(int)
+    output = Signal(str)
+    done = Signal(object)
+
+
+class FlashTab(QWidget):
+    def __init__(self, serial_tab, parent: QWidget | None = None):
+        super().__init__(parent)
+        self.serial_tab = serial_tab
+        self._images: list[FirmwareImage] = []
+        self._ports: list[PortInfo] = []   # before any signal can call _update()
+        self._runner: FlashRunner | None = None
+        self._port: PortInfo | None = None
+        self._image: FirmwareImage | None = None
+
+        # 1. box
+        box = QGroupBox("1. Sensorbox")
+        self.port_combo = QComboBox(minimumWidth=360)
+        refresh = QPushButton("Refresh")
+        refresh.clicked.connect(self.refresh_ports)
+        self.box_fw = QLabel(wordWrap=True)
+        bl = QVBoxLayout(box)
+        row = QHBoxLayout()
+        row.addWidget(self.port_combo)
+        row.addWidget(refresh)
+        row.addStretch(1)
+        bl.addLayout(row)
+        bl.addWidget(self.box_fw)
+
+        # 2. firmware
+        fwbox = QGroupBox("2. Firmware")
+        self.image_combo = QComboBox(minimumWidth=360)
+        self.import_btn = QPushButton("Import firmware file...")
+        self.import_btn.setToolTip("Add a newer build the firmware team sent you (.bin)")
+        self.import_btn.clicked.connect(self._import)
+        self.remove_btn = QPushButton("Remove from list")
+        self.remove_btn.clicked.connect(self._remove)
+        self.image_info = QLabel(wordWrap=True)
+        self.image_info.setTextInteractionFlags(Qt.TextInteractionFlag.TextSelectableByMouse)
+        fl = QVBoxLayout(fwbox)
+        fl.addWidget(self.image_combo)
+        brow = QHBoxLayout()
+        brow.addWidget(self.import_btn)
+        brow.addWidget(self.remove_btn)
+        brow.addStretch(1)
+        fl.addLayout(brow)
+        fl.addWidget(self.image_info)
+        self._library = FirmwareLibrary()
+        self._reference: FirmwareImage | None = None
+        self._problems: list[str] = []
+
+        # 3. mode
+        modebox = QGroupBox("3. What to write")
+        self.rb_app = QRadioButton("App only  (recommended for repairs)")
+        self.rb_full = QRadioButton("Full factory image  (new or completely wiped boards)")
+        self.mode_group = QButtonGroup(self)
+        self.mode_group.addButton(self.rb_app)
+        self.mode_group.addButton(self.rb_full)
+        self.rb_app.setChecked(True)
+        app_note = QLabel("Replaces the firmware only. Keeps the Matter pairing, the OTA registration and the "
+                          "settings stored on the box.", wordWrap=True)
+        full_note = QLabel("Writes everything like the factory. <b>Erases the Matter pairing and the OTA "
+                           "registration</b> - the box must be paired again afterwards.", wordWrap=True)
+        for n in (app_note, full_note):
+            n.setContentsMargins(24, 0, 0, 6)
+            n.setStyleSheet("color:#555")
+        self.confirm_full = QCheckBox("I understand the pairing and OTA registration will be erased")
+        self.backup = QCheckBox("Back up the box's complete flash first (8 MB, about 3 minutes)")
+        ml = QVBoxLayout(modebox)
+        for w in (self.rb_app, app_note, self.rb_full, full_note, self.confirm_full, self.backup):
+            ml.addWidget(w)
+
+        # 4. run
+        runbox = QGroupBox("4. Flash")
+        self.plan_label = QLabel(wordWrap=True)
+        self.start_btn = QPushButton("Start flashing")
+        self.start_btn.setMinimumHeight(36)
+        self.start_btn.clicked.connect(self._start)
+        self.step_label = QLabel()
+        self.bar = QProgressBar()
+        self.result = QLabel(wordWrap=True)
+        self.result.setMargin(8)
+        self.result.setTextFormat(Qt.TextFormat.RichText)
+        self.details_btn = QPushButton("Show esptool output")
+        self.details_btn.setCheckable(True)
+        self.output = QPlainTextEdit(readOnly=True)
+        self.output.setVisible(False)
+        self.details_btn.toggled.connect(self.output.setVisible)
+        rl = QVBoxLayout(runbox)
+        for w in (self.plan_label, self.start_btn, self.step_label, self.bar, self.result, self.details_btn, self.output):
+            rl.addWidget(w)
+        help_lbl = QLabel(HELP, wordWrap=True)
+        help_lbl.setStyleSheet("color:#555")
+        rl.addWidget(help_lbl)
+        rl.addStretch(1)   # keep the run column packed at the top
+
+        left = QVBoxLayout()
+        for w in (box, fwbox, modebox):
+            left.addWidget(w)
+        left.addStretch(1)
+        lay = QHBoxLayout(self)
+        lay.addLayout(left, 1)
+        lay.addWidget(runbox, 1)
+
+        self._bridge = _Bridge()
+        self._bridge.step.connect(self._on_step)
+        self._bridge.progress.connect(self.bar.setValue)
+        self._bridge.output.connect(self.output.appendPlainText)
+        self._bridge.done.connect(self._on_done)
+        self._verify_timer = QTimer(self, interval=500)
+        self._verify_timer.timeout.connect(self._check_verify)
+
+        for sig in (self.rb_app.toggled, self.confirm_full.toggled, self.backup.toggled):
+            sig.connect(self._update)
+        self.rb_full.toggled.connect(lambda on: self.backup.setChecked(on))  # backup default on for Full
+        self.image_combo.currentIndexChanged.connect(self._update)
+        self.port_combo.currentIndexChanged.connect(self._update)
+
+        self._load_images()
+        self.refresh_ports()
+        self._show_result("", None)
+
+    # ------------------------------------------------------------ setup
+    def _load_images(self, select_sha: str | None = None) -> None:
+        self._problems = []
+        try:
+            bundled = bundled_images()
+        except ImageError as exc:
+            bundled = []
+            self._problems.append(f"bundled image: {exc}")
+        factory = [i for i in bundled if not i.is_developer]
+        self._reference = factory[0] if factory else None
+        dev, problems = self._library.images(self._reference)
+        dev += [i for i in bundled if i.is_developer]
+        self._problems += problems
+        # Newest developer builds first, then the factory image.
+        dev.sort(key=lambda i: i.app.built_at or dt.datetime.min, reverse=True)
+        self._images = dev + factory
+        self.image_combo.blockSignals(True)
+        self.image_combo.clear()
+        for img in self._images:
+            self.image_combo.addItem(img.label())
+        if not self._images:
+            self.image_combo.addItem("No firmware image available - import one")
+        idx = next((i for i, im in enumerate(self._images) if im.sha256 == select_sha), None)
+        if idx is None:
+            idx = len(dev) if factory else 0          # default: the factory image
+        self.image_combo.setCurrentIndex(idx)
+        self.image_combo.blockSignals(False)
+        self._update()
+
+    def _import(self) -> None:
+        path, _ = QFileDialog.getOpenFileName(self, "Import firmware from the firmware team", str(Path.home()),
+                                              "Firmware (*.bin);;All files (*)")
+        if not path:
+            return
+        built_by, ok = QInputDialog.getText(self, "Who built this firmware?",
+                                            "Name of the developer who built this image (shown next to it):")
+        if not ok:
+            return
+        try:
+            img = self._library.import_file(Path(path), self._reference, built_by=built_by)
+        except (ImageError, OSError) as exc:
+            QMessageBox.warning(self, "Cannot use this file", f"This file cannot be flashed:\n\n{exc}")
+            return
+        self._load_images(select_sha=img.sha256)
+        kind = "complete image" if img.kind == "merged" else "app only"
+        QMessageBox.information(
+            self, "Firmware imported",
+            f"{img.name}\nbuild {img.app.elf_sha[:9]}, {kind}\n\nFile fingerprint (SHA-256):\n{img.sha256}\n\n"
+            "Compare it with the fingerprint the firmware team sent you before flashing.")
+
+    def _remove(self) -> None:
+        img = self._selected_image()
+        if img and img.is_developer and QMessageBox.question(
+                self, "Remove firmware", f"Remove {img.name} from this computer?") == QMessageBox.StandardButton.Yes:
+            self._library.remove(img.sha256)
+            self._load_images()
+
+    def refresh_ports(self) -> None:
+        current = self.port_combo.currentData()
+        self._ports = list_serial_ports()
+        self.port_combo.clear()
+        for p in self._ports:
+            self.port_combo.addItem(p.label, p.device)
+        if not self._ports:
+            self.port_combo.addItem("No sensorbox found - check USB cable and power switch", None)
+        self.port_combo.setCurrentIndex(max(self.port_combo.findData(current), 0))
+        self._update()
+
+    def showEvent(self, event):  # noqa: N802 - refresh when the tab is opened
+        self.refresh_ports()
+        super().showEvent(event)
+
+    # ------------------------------------------------------------ state
+    def _selected_image(self) -> FirmwareImage | None:
+        i = self.image_combo.currentIndex()
+        return self._images[i] if 0 <= i < len(self._images) else None
+
+    def _selected_port(self) -> PortInfo | None:
+        dev = self.port_combo.currentData()
+        return next((p for p in self._ports if p.device == dev), None)
+
+    def _update(self) -> None:
+        img = self._selected_image()
+        info = ""
+        if img:
+            a = img.app
+            origin = ("<b>Factory image</b> (bundled with the tool)" if not img.is_developer else
+                      "<b style='color:#c77c02'>Developer build</b> - only flash builds you received "
+                      "from the firmware team")
+            kind = "complete image (bootloader + layout + app)" if img.kind == "merged" else "app only"
+            info = (f"{origin}<br>{a.project} {a.version}, built {a.built}, ESP-IDF {a.idf}, {kind}<br>"
+                    f"<small>build {a.elf_sha[:9]} &middot; file SHA-256 {img.sha256[:16]}... "
+                    f"&middot; checksum OK</small>" + (f"<br><small>{img.notes}</small>" if img.notes else ""))
+        if self._problems:
+            info += ("<br><span style='color:#b03a2e'><b>Not offered:</b> "
+                     + "; ".join(self._problems) + "</span>")
+        self.image_info.setText(info)
+        self.remove_btn.setEnabled(bool(img and img.is_developer) and self._runner is None)
+        # An app-only file has no bootloader/layout: Full mode is impossible.
+        full_ok = bool(img and img.kind == "merged")
+        self.rb_full.setEnabled(full_ok and self._runner is None)
+        if not full_ok and self.rb_full.isChecked():
+            self.rb_app.setChecked(True)
+        self.box_fw.setText(self._box_text(img))
+
+        self.confirm_full.setVisible(self.rb_full.isChecked())
+        ok = bool(img and self._selected_port() and self._runner is None
+                  and (self.rb_app.isChecked() or self.confirm_full.isChecked()))
+        self.start_btn.setEnabled(ok)
+        if img and self._selected_port():
+            mode = Mode.APP_ONLY if self.rb_app.isChecked() else Mode.FULL
+            steps = ["Back up the complete flash (~3 min)"] if self.backup.isChecked() else []
+            if mode == Mode.APP_ONLY:
+                steps += ["Check the box has the same partition layout", "Write the firmware app (~20 s)"]
+            else:
+                steps += ["Write the complete factory image (~25 s)"]
+            steps += ["Restart the box and verify the new firmware boots"]
+            self.plan_label.setText("<b>Plan:</b><ol>" + "".join(f"<li>{s}</li>" for s in steps) + "</ol>")
+        else:
+            self.plan_label.setText("Select a sensorbox and a firmware image.")
+
+    def _box_text(self, img: FirmwareImage | None) -> str:
+        fw = self.serial_tab.engine.firmware
+        if not fw.elf_sha:
+            return "Firmware on the box: unknown - connect in the Serial monitor and press Reset & capture to see it."
+        msg = f"Box currently runs: {fw.describe()}" + (f", built {fw.built}" if fw.built else "")
+        if not img:
+            return msg
+        if fw.elf_sha.startswith(img.app.elf_sha[:9]) or img.app.elf_sha.startswith(fw.elf_sha):
+            return msg + "<br><i>It already has this firmware. Re-flash only if you suspect the firmware is damaged.</i>"
+        box_built, img_built = _parse_built(fw.built), img.app.built_at
+        if box_built and img_built and img_built > box_built:
+            return msg + f"<br><b style='color:#2e6da4'>The selected firmware is newer (built {img.app.built}).</b>"
+        if box_built and img_built and img_built < box_built:
+            return msg + ("<br><b style='color:#c77c02'>The selected firmware is OLDER than the box's (the box was "
+                          "probably updated over OTA). The box updates itself again once online.</b>")
+        return msg + "<br><b style='color:#c77c02'>The box runs a different build.</b>"
+
+    # ------------------------------------------------------------ flash
+    def _start(self) -> None:
+        img, port = self._selected_image(), self._selected_port()
+        if not img or not port:
+            return
+        mode = Mode.APP_ONLY if self.rb_app.isChecked() else Mode.FULL
+        what = ("the firmware app (pairing and settings are kept)" if mode == Mode.APP_ONLY
+                else "the COMPLETE factory image (pairing and OTA registration are erased)")
+        if QMessageBox.question(self, "Flash firmware",
+                                f"Write {what}\n\nImage: {img.name}\nBox: {port.label}\n\n"
+                                "Keep the box powered and the USB cable connected until it finishes.",
+                                QMessageBox.StandardButton.Ok | QMessageBox.StandardButton.Cancel
+                                ) != QMessageBox.StandardButton.Ok:
+            return
+        backup_to = None
+        if self.backup.isChecked():
+            BACKUP_DIR.mkdir(parents=True, exist_ok=True)
+            stamp = dt.datetime.now().strftime("%Y%m%d_%H%M%S")
+            backup_to = BACKUP_DIR / f"{(port.mac or port.device).replace(':', '')}_{stamp}.bin"
+        plan = build_plan(img, mode, port.device, Path(tempfile.mkdtemp(prefix="kota_flash_")), backup_to)
+
+        self._port, self._image = port, img
+        self.serial_tab.release_port()          # esptool needs the port exclusively
+        self.output.clear()
+        self.output.appendPlainText("\n".join(plan.summary()))
+        self._show_result("", None)
+        self._runner = FlashRunner(plan, self._bridge.step.emit, self._bridge.progress.emit,
+                                   self._bridge.output.emit, self._bridge.done.emit)
+        self._set_busy(True)
+        self._runner.start()
+
+    def _set_busy(self, busy: bool) -> None:
+        for w in (self.port_combo, self.image_combo, self.rb_app, self.backup, self.confirm_full, self.import_btn):
+            w.setEnabled(not busy)
+        self._update()
+
+    def _on_step(self, i: int, title: str) -> None:
+        n = len(self._runner.plan.steps) if self._runner else 0
+        self.step_label.setText(f"Step {i + 1} of {n + 1}: {title}")
+
+    def _on_done(self, res: Result) -> None:
+        self._runner = None
+        if not res.ok:
+            self._set_busy(False)
+            self.step_label.setText("Stopped.")
+            hint = f"<p>{res.hint}</p>" if res.hint else ""
+            self._show_result(f"<b>Flashing failed.</b> {res.message}{hint}", "error")
+            self.details_btn.setChecked(True)
+            return
+        self.step_label.setText("Final step: restarting the box and checking which firmware it boots...")
+        self.bar.setValue(0)
+        self._show_result("Firmware written. Waiting for the box to start...", "info")
+        self.serial_tab.connect_port(self._port, capture=True)
+        self._verify_ms = 0
+        self._verify_timer.start()
+
+    def _check_verify(self) -> None:
+        self._verify_ms += self._verify_timer.interval()
+        self.bar.setValue(min(100, int(100 * self._verify_ms / VERIFY_TIMEOUT_MS)))
+        fw = self.serial_tab.engine.firmware
+        want = self._image.app.elf_sha[:9]
+        done = fw.elf_sha is not None and fw.elf_sha.startswith(want)
+        if done or self._verify_ms >= VERIFY_TIMEOUT_MS:
+            self._verify_timer.stop()
+            self._set_busy(False)
+            self.bar.setValue(100)
+            if done:
+                self.step_label.setText("Done.")
+                self._show_result(f"<b>Success.</b> The box boots the new firmware (build {want}). "
+                                  "Check the Diagnosis panel in the Serial monitor.", "ok")
+            else:
+                seen = fw.elf_sha[:9] if fw.elf_sha else "no boot seen"
+                self._show_result(f"<b>Written, but not verified.</b> Expected build {want}, saw: {seen}. "
+                                  "Open the Serial monitor and press Reset & capture.", "warning")
+
+    def _show_result(self, html: str, kind: str | None) -> None:
+        colours = {"ok": ("#2e9e44", "#e3f4e7"), "info": ("#2e6da4", "#e3edf7"),
+                   "warning": ("#c77c02", "#fdf0d6"), "error": ("#d9534f", "#f9e0df")}
+        self.result.setVisible(bool(html))
+        if html:
+            border, bg = colours[kind or "info"]
+            self.result.setStyleSheet(f"QLabel {{ border:2px solid {border}; background:{bg}; border-radius:6px; }}")
+            self.result.setText(html)
+
+
+def _parse_built(s: str | None) -> dt.datetime | None:
+    """'Jun 29 2026 11:03:32' (app_init "Compile time") -> datetime."""
+    if not s:
+        return None
+    try:
+        return dt.datetime.strptime(" ".join(s.split()), "%b %d %Y %H:%M:%S")
+    except ValueError:
+        return None

kota_tech/ui/guide_panel.py

@@ -0,0 +1,225 @@
+"""Guided troubleshooting panel: renders a diag.guides.GuideRunner."""
+
+from __future__ import annotations
+
+from PySide6.QtCore import QSize, Qt
+from PySide6.QtGui import QBrush, QColor, QIcon, QLinearGradient, QPainter, QPixmap
+from PySide6.QtWidgets import (
+    QFrame,
+    QHBoxLayout,
+    QLabel,
+    QListWidget,
+    QListWidgetItem,
+    QProgressBar,
+    QPushButton,
+    QVBoxLayout,
+    QWidget,
+)
+
+from ..diag.engine import LED, DiagnosticsEngine
+from ..diag.guides import GuideRunner, recommended
+from ..matter.payload import SetupPayload
+from .matter_qr import MatterQrWidget
+
+END_STYLE = {  # end severity -> (border, background)
+    "ok": ("#2e9e44", "#e3f4e7"),
+    "info": ("#2e6da4", "#e3edf7"),
+    "warning": ("#c77c02", "#fdf0d6"),
+    "error": ("#d9534f", "#f9e0df"),
+    "critical": ("#b03a2e", "#f6d5d1"),
+}
+
+
+def _swatch(key: str, size: int = 22) -> QIcon:
+    """Round LED-colour icon; CYCLING is drawn as a blue-dark-red gradient."""
+    pm = QPixmap(size, size)
+    pm.fill(QColor(0, 0, 0, 0))
+    p = QPainter(pm)
+    p.setRenderHint(QPainter.RenderHint.Antialiasing)
+    if key == "CYCLING":
+        g = QLinearGradient(0, 0, size, 0)
+        for stop, c in ((0.0, "#2f6fd6"), (0.5, "#444444"), (1.0, "#d64541")):
+            g.setColorAt(stop, QColor(c))
+        p.setBrush(QBrush(g))
+    else:
+        p.setBrush(QColor(LED.get(key, ("", "#888888"))[1]))
+    p.setPen(QColor("#777777"))
+    p.drawEllipse(1, 1, size - 2, size - 2)
+    p.end()
+    return QIcon(pm)
+
+
+def _esc(s: str) -> str:
+    return s.replace("&", "&amp;").replace("<", "&lt;").replace(">", "&gt;")
+
+
+class GuidePanel(QWidget):
+    def __init__(self, runner: GuideRunner, engine: DiagnosticsEngine, parent: QWidget | None = None,
+                 matter_payload=None):
+        super().__init__(parent)
+        self.runner, self.engine = runner, engine
+        self._matter_payload = matter_payload or SetupPayload   # callable -> SetupPayload
+        self._shown_key: tuple | None = None
+
+        # --- picker (no guide running)
+        self.picker = QWidget()
+        pl = QVBoxLayout(self.picker)
+        pl.setContentsMargins(0, 0, 0, 0)
+        pl.addWidget(QLabel("<b>Recommended checks for this box</b> (based on the log):"))
+        self.guide_list = QListWidget()
+        self.guide_list.itemDoubleClicked.connect(lambda it: self._start(it.data(Qt.ItemDataRole.UserRole)))
+        pl.addWidget(self.guide_list, 1)
+        self.start_btn = QPushButton("Start selected check")
+        self.start_btn.clicked.connect(self._start_selected)
+        pl.addWidget(self.start_btn)
+
+        # --- running guide
+        self.card = QFrame()
+        self.card.setFrameShape(QFrame.Shape.StyledPanel)
+        cl = QVBoxLayout(self.card)
+        self.guide_title = QLabel()
+        self.guide_title.setStyleSheet("color:#666")
+        self.step_text = QLabel(wordWrap=True)
+        f = self.step_text.font()
+        f.setPointSize(f.pointSize() + 2)
+        self.step_text.setFont(f)
+        self.step_text.setTextFormat(Qt.TextFormat.RichText)
+        self.options = QVBoxLayout()
+        self.wait_bar = QProgressBar()
+        self.wait_bar.setTextVisible(False)
+        self.wait_label = QLabel()
+        self.note = QLabel(wordWrap=True)
+        self.note.setStyleSheet("color:#b03a2e")
+        self.continue_btn = QPushButton("Continue")
+        self.continue_btn.clicked.connect(self._proceed)
+        self.skip_btn = QPushButton("Skip waiting / it did not work")
+        self.skip_btn.clicked.connect(self._proceed)
+        self.end_box = QLabel(wordWrap=True)
+        self.end_box.setTextFormat(Qt.TextFormat.RichText)
+        self.end_box.setMargin(10)
+        self.qr = MatterQrWidget(SetupPayload(), 220)
+        for w in (self.guide_title, self.step_text, self.qr):
+            cl.addWidget(w)
+        cl.addLayout(self.options)
+        for w in (self.wait_label, self.wait_bar, self.note, self.continue_btn, self.skip_btn, self.end_box):
+            cl.addWidget(w)
+        cl.addStretch(1)
+        nav = QHBoxLayout()
+        self.back_btn = QPushButton("← Back")
+        self.back_btn.clicked.connect(self._back)
+        self.done_btn = QPushButton("Back to checks list")
+        self.done_btn.clicked.connect(self._cancel)
+        nav.addWidget(self.back_btn)
+        nav.addStretch(1)
+        nav.addWidget(self.done_btn)
+        cl.addLayout(nav)
+
+        lay = QVBoxLayout(self)
+        lay.setContentsMargins(4, 0, 0, 0)
+        lay.addWidget(self.picker, 1)
+        lay.addWidget(self.card, 1)
+        self.refresh()
+
+    # ------------------------------------------------------------ actions
+    def _start_selected(self) -> None:
+        it = self.guide_list.currentItem() or self.guide_list.item(0)
+        if it:
+            self._start(it.data(Qt.ItemDataRole.UserRole))
+
+    def _start(self, guide_id: str) -> None:
+        self.runner.start(guide_id)
+        self.refresh()
+
+    def _answer(self, key: str) -> None:
+        self.runner.answer(key)
+        self.refresh()
+
+    def _proceed(self) -> None:
+        self.runner.proceed()
+        self.refresh()
+
+    def _back(self) -> None:
+        self.runner.back()
+        self.refresh()
+
+    def _cancel(self) -> None:
+        self.runner.cancel()
+        self.refresh()
+
+    # ------------------------------------------------------------- render
+    def refresh(self) -> None:
+        """Called after every interaction and periodically (timeouts, countdown)."""
+        self.runner.tick()
+        v = self.runner.view()
+        running = v.guide is not None
+        self.picker.setVisible(not running)
+        self.card.setVisible(running)
+        if not running:
+            self._fill_picker()
+            self._shown_key = None
+            return
+        key = (v.guide.id, v.step.id if v.step else None, v.end.id if v.end else None)
+        if key != self._shown_key:
+            self._shown_key = key
+            self._render_step(v)
+        if v.waiting:
+            total = v.step.timeout_s
+            self.wait_bar.setMaximum(int(total))
+            self.wait_bar.setValue(int(total - v.remaining_s))
+            m, s = divmod(int(v.remaining_s), 60)
+            self.wait_label.setText(f"Watching the live log... {m}:{s:02d} left")
+        self.note.setText(v.note)
+        self.note.setVisible(bool(v.note))
+        self.back_btn.setEnabled(v.can_back)
+
+    def _fill_picker(self) -> None:
+        wanted = [(g.id, g.title, g.summary) for g in recommended(self.runner.guides, self.engine)]
+        current = [(self.guide_list.item(i).data(Qt.ItemDataRole.UserRole)) for i in range(self.guide_list.count())]
+        if [w[0] for w in wanted] == current:
+            return
+        self.guide_list.clear()
+        for gid, title, summary in wanted:
+            it = QListWidgetItem(f"{title}\n    {summary}")
+            it.setData(Qt.ItemDataRole.UserRole, gid)
+            self.guide_list.addItem(it)
+        self.guide_list.setCurrentRow(0)
+
+    def _render_step(self, v) -> None:
+        self.guide_title.setText(v.guide.title)
+        while self.options.count():
+            w = self.options.takeAt(0).widget()
+            if w:
+                # Detach now; deleteLater alone leaves it visible until the
+                # event loop processes the deferred delete.
+                w.hide()
+                w.setParent(None)
+                w.deleteLater()
+        is_end = v.end is not None
+        self.step_text.setVisible(not is_end)
+        self.step_text.setText(_esc(v.text))
+        show_qr = bool(v.step and v.step.show_qr)
+        if show_qr:
+            self.qr.set_payload(self._matter_payload())
+        self.qr.setVisible(show_qr)
+        for opt_key, label in v.options:
+            b = QPushButton(label)
+            b.setMinimumHeight(34)
+            if v.step and v.step.type == "led":
+                b.setIcon(_swatch(opt_key))
+                b.setIconSize(QSize(22, 22))
+                b.setStyleSheet("QPushButton { text-align:left; padding-left:10px; }")
+            b.clicked.connect(lambda _=False, k=opt_key: self._answer(k))
+            self.options.addWidget(b)
+        step_type = v.step.type if v.step else None
+        self.continue_btn.setVisible(step_type == "info")
+        self.skip_btn.setVisible(step_type == "wait")
+        self.wait_bar.setVisible(step_type == "wait")
+        self.wait_label.setVisible(step_type == "wait")
+        self.end_box.setVisible(is_end)
+        if is_end:
+            e = v.end
+            border, bg = END_STYLE.get(e.severity, END_STYLE["info"])
+            acts = "".join(f"<li>{_esc(a)}</li>" for a in e.actions)
+            self.end_box.setStyleSheet(f"QLabel {{ border:2px solid {border}; background:{bg}; border-radius:6px; }}")
+            self.end_box.setText(f"<h3 style='margin:0'>{_esc(e.title)}</h3><p>{_esc(e.text)}</p>"
+                                 + (f"<ol>{acts}</ol>" if acts else ""))

kota_tech/ui/main_window.py

@@ -1,299 +1,415 @@
-from __future__ import annotations
+from __future__ import annotations
-
+
-from pathlib import Path
+from pathlib import Path
-
+
-from PySide6.QtCore import QObject, Qt, QTimer, QUrl, Signal
+from PySide6.QtCore import QCoreApplication, QObject, QSettings, Qt, QTimer, QUrl, Signal
-from PySide6.QtGui import QColor, QDesktopServices, QFont, QGuiApplication, QTextCharFormat, QTextCursor
+from PySide6.QtGui import QColor, QDesktopServices, QFont, QGuiApplication, QTextCharFormat, QTextCursor
-from PySide6.QtWidgets import (
+from PySide6.QtWidgets import (
-    QCheckBox,
+    QCheckBox,
-    QComboBox,
+    QComboBox,
-    QFileDialog,
+    QFileDialog,
-    QHBoxLayout,
+    QHBoxLayout,
-    QLabel,
+    QInputDialog,
-    QMainWindow,
+    QLabel,
-    QPlainTextEdit,
+    QMainWindow,
-    QPushButton,
+    QMessageBox,
-    QSplitter,
+    QPlainTextEdit,
-    QTabWidget,
+    QPushButton,
-    QTextBrowser,
+    QSplitter,
-    QVBoxLayout,
+    QTabWidget,
-    QWidget,
+    QTextBrowser,
-)
+    QVBoxLayout,
-
+    QWidget,
-from .. import __version__
+)
-from ..core.logfile import read_log_file
+
-from ..core.logline import LineKind, LogLine
+from .. import __version__
-from ..core.session import SessionLog
+from ..core.logfile import read_log_file
-from ..diag.engine import DiagnosticsEngine
+from ..core.logline import LineKind, LogLine, host_event
-from ..serialio.manager import SerialManager, State
+from ..core.session import SessionLog
-from ..serialio.ports import PortInfo, list_serial_ports
+from ..diag.engine import DiagnosticsEngine
-from .cheatsheet import cheatsheet_html
+from ..diag.guides import GuideRunner
-from .diag_panel import DiagnosticsPanel
+from ..serialio.manager import SerialManager, State
-
+from ..serialio.ports import PortInfo, list_serial_ports
-MAX_LINES = 20000
+from ..matter.payload import SetupPayload, payload_from_log
-LEVEL_FILTERS = {"All lines": None, "Warnings + errors": {"W", "E"}, "Errors only": {"E"}}
+from ..service.report import DEFAULT_BASE, normalize_mac, report_url
-COLORS = {
+from .cheatsheet import cheatsheet_html
-    "E": "#ff6b6b",
+from .diag_panel import DiagnosticsPanel
-    "W": "#f5c451",
+from .flash_tab import FlashTab
-    "I": "#d4d4d4",
+from .matter_qr import MatterQrDialog
-    LineKind.BOOT: "#6fc3ff",
+from .guide_panel import GuidePanel
-    LineKind.RESET: "#6fc3ff",
+from .sd_tab import SdTab
-    LineKind.PANIC: "#ff4dd2",
+
-    LineKind.HOST: "#7ee07e",
+MAX_LINES = 20000
-    LineKind.RAW: "#a8a8a8",
+LEVEL_FILTERS = {"All lines": None, "Warnings + errors": {"W", "E"}, "Errors only": {"E"}}
-}
+COLORS = {
-
+    "E": "#ff6b6b",
-
+    "W": "#f5c451",
-class _Bridge(QObject):
+    "I": "#d4d4d4",
-    """Marshals SerialManager callbacks (reader thread) onto the UI thread."""
+    LineKind.BOOT: "#6fc3ff",
-
+    LineKind.RESET: "#6fc3ff",
-    line = Signal(object)
+    LineKind.PANIC: "#ff4dd2",
-    state = Signal(object, str)
+    LineKind.HOST: "#7ee07e",
-
+    LineKind.RAW: "#a8a8a8",
-
+}
-class SerialTab(QWidget):
+
-    def __init__(self, parent: QWidget | None = None):
+
-        super().__init__(parent)
+class _Bridge(QObject):
-        self._bridge = _Bridge()
+    """Marshals SerialManager callbacks (reader thread) onto the UI thread."""
-        self._bridge.line.connect(self._on_line)
+
-        self._bridge.state.connect(self._on_state)
+    line = Signal(object)
-        self._manager = SerialManager(self._bridge.line.emit, self._bridge.state.emit)
+    state = Signal(object, str)
-        self._session = SessionLog()
+
-        self._ports: list[PortInfo] = []
+
-        self._counts = {"E": 0, "W": 0, "boots": 0}
+class SerialTab(QWidget):
-        self._engine = DiagnosticsEngine()
+    def __init__(self, parent: QWidget | None = None):
-        self._diag_dirty = True
+        super().__init__(parent)
-
+        self._bridge = _Bridge()
-        # --- controls
+        self._bridge.line.connect(self._on_line)
-        self.port_combo = QComboBox(minimumWidth=320)
+        self._bridge.state.connect(self._on_state)
-        self.all_ports = QCheckBox("Show all ports")
+        self._manager = SerialManager(self._bridge.line.emit, self._bridge.state.emit)
-        self.refresh_btn = QPushButton("Refresh")
+        self._session = SessionLog()
-        self.connect_btn = QPushButton("Connect")
+        self._ports: list[PortInfo] = []
-        self.reset_btn = QPushButton("Reset && capture")
+        self._counts = {"E": 0, "W": 0, "boots": 0}
-        self.reset_btn.setToolTip("Reboot the sensorbox and record the log from the first boot line")
+        self._engine = DiagnosticsEngine()
-        self.filter_combo = QComboBox()
+        self._diag_dirty = True
-        self.filter_combo.addItems(LEVEL_FILTERS)
+        self._runner = GuideRunner(self._engine, on_action=self._guide_action, on_log=self._guide_log)
-        self.clear_btn = QPushButton("Clear view")
+
-        self.save_btn = QPushButton("Save view as...")
+        # --- controls
-        self.folder_btn = QPushButton("Open logs folder")
+        self.port_combo = QComboBox(minimumWidth=320)
-        self.analyze_btn = QPushButton("Analyze log file...")
+        self.all_ports = QCheckBox("Show all ports")
-        self.analyze_btn.setToolTip("Load a saved session log or serial capture and diagnose it")
+        self.refresh_btn = QPushButton("Refresh")
-        self.copy_btn = QPushButton("Copy report")
+        self.connect_btn = QPushButton("Connect")
-        self.copy_btn.setToolTip("Copy the diagnosis as text (e.g. to send to the firmware team)")
+        self.reset_btn = QPushButton("Reset && capture")
-
+        self.reset_btn.setToolTip("Reboot the sensorbox and record the log from the first boot line")
-        row1 = QHBoxLayout()
+        self.filter_combo = QComboBox()
-        for w in (QLabel("Port:"), self.port_combo, self.all_ports, self.refresh_btn,
+        self.filter_combo.addItems(LEVEL_FILTERS)
-                  self.connect_btn, self.reset_btn):
+        self.clear_btn = QPushButton("Clear view")
-            row1.addWidget(w)
+        self.save_btn = QPushButton("Save view as...")
-        row1.addStretch(1)
+        self.folder_btn = QPushButton("Open logs folder")
-        row2 = QHBoxLayout()
+        self.analyze_btn = QPushButton("Analyze log file...")
-        for w in (QLabel("Show:"), self.filter_combo, self.clear_btn, self.save_btn, self.folder_btn,
+        self.analyze_btn.setToolTip("Load a saved session log or serial capture and diagnose it")
-                  self.analyze_btn, self.copy_btn):
+        self.copy_btn = QPushButton("Copy report")
-            row2.addWidget(w)
+        self.copy_btn.setToolTip("Copy the diagnosis as text (e.g. to send to the firmware team)")
-        row2.addStretch(1)
+        self.service_btn = QPushButton("Service report...")
-
+        self.service_btn.setToolTip("Open this box's page in the KOTA service system with the diagnosis "
-        self.view = QPlainTextEdit(readOnly=True)
+                                    "filled in; check it and press Save there")
-        self.view.setMaximumBlockCount(MAX_LINES)
+        self._settings = QSettings("KOTA", "TechnicianTool")
-        self.view.setLineWrapMode(QPlainTextEdit.LineWrapMode.NoWrap)
+        self.auto_service = QCheckBox("Open service report on disconnect")
-        mono = QFont("Menlo" if QFont("Menlo").exactMatch() else "Consolas")
+        self.auto_service.setChecked(self._settings.value("service/auto", False, type=bool))
-        mono.setStyleHint(QFont.StyleHint.Monospace)
+        self.auto_service.toggled.connect(lambda on: self._settings.setValue("service/auto", on))
-        mono.setPointSize(10)
+        self._active_port: PortInfo | None = None
-        self.view.setFont(mono)
+
-        self.view.setStyleSheet("QPlainTextEdit { background:#1e1e1e; color:#d4d4d4; }")
+        row1 = QHBoxLayout()
-
+        for w in (QLabel("Port:"), self.port_combo, self.all_ports, self.refresh_btn,
-        self.diag = DiagnosticsPanel()
+                  self.connect_btn, self.reset_btn):
-        split = QSplitter(Qt.Orientation.Horizontal)
+            row1.addWidget(w)
-        split.addWidget(self.view)
+        row1.addStretch(1)
-        split.addWidget(self.diag)
+        row2 = QHBoxLayout()
-        split.setStretchFactor(0, 3)
+        for w in (QLabel("Show:"), self.filter_combo, self.clear_btn, self.save_btn, self.folder_btn,
-        split.setStretchFactor(1, 2)
+                  self.analyze_btn, self.copy_btn, self.service_btn, self.auto_service):
-        split.setSizes([700, 480])
+            row2.addWidget(w)
-
+        row2.addStretch(1)
-        self.status = QLabel()
+
-        layout = QVBoxLayout(self)
+        self.view = QPlainTextEdit(readOnly=True)
-        layout.addLayout(row1)
+        self.view.setMaximumBlockCount(MAX_LINES)
-        layout.addLayout(row2)
+        self.view.setLineWrapMode(QPlainTextEdit.LineWrapMode.NoWrap)
-        layout.addWidget(split, 1)
+        mono = QFont("Menlo" if QFont("Menlo").exactMatch() else "Consolas")
-        layout.addWidget(self.status)
+        mono.setStyleHint(QFont.StyleHint.Monospace)
-
+        mono.setPointSize(10)
-        # --- wiring
+        self.view.setFont(mono)
-        self.refresh_btn.clicked.connect(self.refresh_ports)
+        self.view.setStyleSheet("QPlainTextEdit { background:#1e1e1e; color:#d4d4d4; }")
-        self.all_ports.toggled.connect(self.refresh_ports)
+
-        self.connect_btn.clicked.connect(self._toggle_connect)
+        self.diag = DiagnosticsPanel()
-        self.reset_btn.clicked.connect(self._manager.reset_board)
+        self.guide = GuidePanel(self._runner, self._engine, matter_payload=self.matter_payload)
-        self.clear_btn.clicked.connect(self.view.clear)
+        self.side_tabs = QTabWidget()
-        self.save_btn.clicked.connect(self._save_view)
+        self.side_tabs.addTab(self.diag, "Diagnosis")
-        self.folder_btn.clicked.connect(self._open_folder)
+        self.side_tabs.addTab(self.guide, "Guided troubleshooting")
-        self.analyze_btn.clicked.connect(self._analyze_file)
+        split = QSplitter(Qt.Orientation.Horizontal)
-        self.copy_btn.clicked.connect(self._copy_report)
+        split.addWidget(self.view)
-
+        split.addWidget(self.side_tabs)
-        # Report refresh is throttled; lines can arrive at >100/s.
+        split.setStretchFactor(0, 3)
-        self._diag_timer = QTimer(self, interval=400)
+        split.setStretchFactor(1, 2)
-        self._diag_timer.timeout.connect(self._refresh_diag)
+        split.setSizes([700, 480])
-        self._diag_timer.start()
+
-
+        self.status = QLabel()
-        # Auto-detect a box being plugged in while idle.
+        layout = QVBoxLayout(self)
-        self._poll = QTimer(self, interval=2000)
+        layout.addLayout(row1)
-        self._poll.timeout.connect(self._auto_refresh)
+        layout.addLayout(row2)
-        self._poll.start()
+        layout.addWidget(split, 1)
-
+        layout.addWidget(self.status)
-        self.refresh_ports()
+
-        self._on_state(State.DISCONNECTED, "")
+        # --- wiring
-
+        self.refresh_btn.clicked.connect(self.refresh_ports)
-    # ---- ports -------------------------------------------------------
+        self.all_ports.toggled.connect(self.refresh_ports)
-    def refresh_ports(self) -> None:
+        self.connect_btn.clicked.connect(self._toggle_connect)
-        current = self.port_combo.currentData()
+        self.reset_btn.clicked.connect(self._manager.reset_board)
-        self._ports = list_serial_ports(include_all=self.all_ports.isChecked())
+        self.clear_btn.clicked.connect(self.view.clear)
-        self.port_combo.clear()
+        self.save_btn.clicked.connect(self._save_view)
-        for p in self._ports:
+        self.folder_btn.clicked.connect(self._open_folder)
-            self.port_combo.addItem(p.label, p.device)
+        self.analyze_btn.clicked.connect(self._analyze_file)
-        if not self._ports:
+        self.copy_btn.clicked.connect(self._copy_report)
-            self.port_combo.addItem("No sensorbox found - check USB cable and power switch", None)
+        self.service_btn.clicked.connect(lambda: self._open_service_report(auto=False))
-        idx = self.port_combo.findData(current)
+        self.diag.qr_btn.clicked.connect(lambda: MatterQrDialog(self.matter_payload(), self).exec())
-        self.port_combo.setCurrentIndex(max(idx, 0))
+
-
+        # Report refresh is throttled; lines can arrive at >100/s.
-    def _auto_refresh(self) -> None:
+        self._diag_timer = QTimer(self, interval=400)
-        if self._manager.is_running:
+        self._diag_timer.timeout.connect(self._refresh_diag)
-            return
+        self._diag_timer.start()
-        devices = [p.device for p in list_serial_ports(self.all_ports.isChecked())]
+
-        if devices != [p.device for p in self._ports]:
+        # Auto-detect a box being plugged in while idle.
-            self.refresh_ports()
+        self._poll = QTimer(self, interval=2000)
-
+        self._poll.timeout.connect(self._auto_refresh)
-    def _selected_port(self) -> PortInfo | None:
+        self._poll.start()
-        dev = self.port_combo.currentData()
+
-        return next((p for p in self._ports if p.device == dev), None)
+        self.refresh_ports()
-
+        self._on_state(State.DISCONNECTED, "")
-    # ---- connection --------------------------------------------------
+
-    def _toggle_connect(self) -> None:
+    # ---- ports -------------------------------------------------------
-        if self._manager.is_running:
+    def refresh_ports(self) -> None:
-            # Session file is closed in _on_state(DISCONNECTED), after the
+        current = self.port_combo.currentData()
-            # reader thread's final queued lines have been written.
+        self._ports = list_serial_ports(include_all=self.all_ports.isChecked())
-            self._manager.disconnect()
+        self.port_combo.clear()
-            return
+        for p in self._ports:
-        port = self._selected_port()
+            self.port_combo.addItem(p.label, p.device)
-        if port is None:
+        if not self._ports:
-            return
+            self.port_combo.addItem("No sensorbox found - check USB cable and power switch", None)
-        self._counts = {"E": 0, "W": 0, "boots": 0}
+        idx = self.port_combo.findData(current)
-        self._engine.reset()
+        self.port_combo.setCurrentIndex(max(idx, 0))
-        self._diag_dirty = True
+
-        self._session.start(port.mac or port.device)
+    def _auto_refresh(self) -> None:
-        self._manager.connect(port)
+        if self._manager.is_running:
-
+            return
-    def _on_state(self, state: State, detail: str) -> None:
+        devices = [p.device for p in list_serial_ports(self.all_ports.isChecked())]
-        running = state != State.DISCONNECTED
+        if devices != [p.device for p in self._ports]:
-        if not running and self._session.path is not None:
+            self.refresh_ports()
-            self._session.write_report(self._engine.report().to_text())
+
-            self._session.stop()
+    def _selected_port(self) -> PortInfo | None:
-        self.connect_btn.setText("Disconnect" if running else "Connect")
+        dev = self.port_combo.currentData()
-        self.reset_btn.setEnabled(state == State.CONNECTED)
+        return next((p for p in self._ports if p.device == dev), None)
-        self.port_combo.setEnabled(not running)
+
-        self.all_ports.setEnabled(not running)
+    # ---- connection --------------------------------------------------
-        self.refresh_btn.setEnabled(not running)
+    def _toggle_connect(self) -> None:
-        # Offline analysis would mix with the live session; disconnect first.
+        if self._manager.is_running:
-        self.analyze_btn.setEnabled(not running)
+            # Session file is closed in _on_state(DISCONNECTED), after the
-        self._state_text = f"{state.value}" + (f" ({detail})" if detail else "")
+            # reader thread's final queued lines have been written.
-        self._update_status()
+            self._manager.disconnect()
-
+            return
-    def _update_status(self) -> None:
+        port = self._selected_port()
-        sess = f"   |   Session log: {self._session.path}" if self._session.path else ""
+        if port is None:
-        c = self._counts
+            return
-        self.status.setText(
+        self._connect(port)
-            f"{getattr(self, '_state_text', '')}   |   boots seen: {c['boots']}   "
+
-            f"errors: {c['E']}   warnings: {c['W']}{sess}"
+    def _connect(self, port: PortInfo) -> None:
-        )
+        self._counts = {"E": 0, "W": 0, "boots": 0}
-
+        self._engine.reset()
-    # ---- lines -------------------------------------------------------
+        self._runner.cancel()
-    def _on_line(self, line: LogLine) -> None:
+        self._diag_dirty = True
-        self._session.write(line)
+        self._session.start(port.mac or port.device)
-        self._engine.feed(line)
+        self._active_port = port
-        self._diag_dirty = True
+        self._manager.connect(port)
-        if line.kind == LineKind.BOOT:
+
-            self._counts["boots"] += 1
+    def matter_payload(self) -> SetupPayload:
-        if line.level in ("E", "W"):
+        """Pairing payload from this box's log (VID/PID/discriminator), defaults otherwise."""
-            self._counts[line.level] += 1
+        return payload_from_log([self._engine.matter_advert] if self._engine.matter_advert else [])
-        self._update_status()
+
-
+    # ---- service system -------------------------------------------------
-        allowed = LEVEL_FILTERS[self.filter_combo.currentText()]
+    def _service_base(self) -> str:
-        if allowed is not None and line.kind != LineKind.HOST and not (
+        return str(self._settings.value("service/base", DEFAULT_BASE))
-            line.level in allowed or line.kind in (LineKind.PANIC, LineKind.BOOT, LineKind.RESET)
+
-        ):
+    def _open_service_report(self, auto: bool) -> None:
-            return
+        mac = normalize_mac(self._engine.mac or (self._active_port.mac if self._active_port else "") or "")
-        self._append(line)
+        if len(mac) != 12:
-
+            if not auto:
-    def _append(self, line: LogLine) -> None:
+                QMessageBox.information(self, "Service report", "The box's MAC address is not known yet. "
-        sb = self.view.verticalScrollBar()
+                                        "Connect to the box and press Reset & capture first.")
-        at_bottom = sb.value() >= sb.maximum() - 4
+            return
-        fmt = QTextCharFormat()
+        url = report_url(mac, self._engine.report(), self._service_base())
-        fmt.setForeground(QColor(COLORS.get(line.level) or COLORS.get(line.kind, "#d4d4d4")))
+        QDesktopServices.openUrl(QUrl(url))
-        if line.kind in (LineKind.PANIC, LineKind.BOOT, LineKind.HOST):
+        # Log that it happened, not the report itself (it is already in the session log).
-            fmt.setFontWeight(QFont.Weight.Bold)
+        self._guide_log(f"service report for {mac} opened in the browser - check it and press Save there")
-        cur = QTextCursor(self.view.document())
+
-        cur.movePosition(QTextCursor.MoveOperation.End)
+    # ---- hand-off with the flash tab ------------------------------------
-        if not self.view.document().isEmpty():
+    @property
-            cur.insertBlock()
+    def engine(self) -> DiagnosticsEngine:
-        cur.insertText(line.text, fmt)
+        return self._engine
-        if at_bottom:
+
-            sb.setValue(sb.maximum())
+    def release_port(self) -> None:
-
+        """Stop monitoring so esptool can open the port exclusively."""
-    # ---- diagnostics -------------------------------------------------
+        if self._manager.is_running:
-    def _refresh_diag(self) -> None:
+            self._no_auto_service = True        # a flash hand-off is not the end of a session
-        if self._diag_dirty:
+            self._manager.disconnect()          # joins the reader thread
-            self._diag_dirty = False
+            QCoreApplication.processEvents()    # deliver its queued final lines/state now
-            self.diag.show_report(self._engine.report())
+            self._no_auto_service = False
-
+
-    def _copy_report(self) -> None:
+    def connect_port(self, port: PortInfo, capture: bool = True) -> None:
-        QGuiApplication.clipboard().setText(self._engine.report().to_text())
+        """Monitor `port`; with capture, restart the box once connected to record its boot."""
-
+        self.release_port()
-    def _analyze_file(self) -> None:
+        idx = self.port_combo.findData(port.device)
-        path, _ = QFileDialog.getOpenFileName(
+        if idx < 0:
-            self, "Analyze log file", str(self._session.root), "Logs (*.log *.txt);;All files (*)")
+            self.port_combo.addItem(port.label, port.device)
-        if not path:
+            self._ports.append(port)
-            return
+            idx = self.port_combo.count() - 1
-        lines = read_log_file(Path(path))
+        self.port_combo.setCurrentIndex(idx)
-        self.view.clear()
+        self._reset_on_connect = capture
-        self._engine.reset()
+        self._connect(port)
-        self._counts = {"E": 0, "W": 0, "boots": 0}
+
-        for line in lines:
+    def _on_state(self, state: State, detail: str) -> None:
-            self._engine.feed(line)
+        running = state != State.DISCONNECTED
-            if line.kind == LineKind.BOOT:
+        if not running and self._manager.is_running:
-                self._counts["boots"] += 1
+            return  # stale event from a session that was already replaced
-            if line.level in ("E", "W"):
+        if state == State.CONNECTED and getattr(self, "_reset_on_connect", False):
-                self._counts[line.level] += 1
+            self._reset_on_connect = False
-            self._append(line)
+            QTimer.singleShot(300, self._manager.reset_board)
-        self._state_text = f"Analyzed file: {Path(path).name} ({len(lines)} lines)"
+        if not running and self._session.path is not None:
-        self._update_status()
+            self._session.write_report(self._engine.report().to_text())
-        self._diag_dirty = True
+            if (self.auto_service.isChecked() and self._engine.lines
-        self._refresh_diag()
+                    and not getattr(self, "_no_auto_service", False)):
-
+                self._open_service_report(auto=True)
-    # ---- misc --------------------------------------------------------
+            self._session.stop()
-    def _save_view(self) -> None:
+        self.connect_btn.setText("Disconnect" if running else "Connect")
-        path, _ = QFileDialog.getSaveFileName(self, "Save log view", "sensorbox_log.txt", "Text (*.txt)")
+        self.reset_btn.setEnabled(state == State.CONNECTED)
-        if path:
+        self.port_combo.setEnabled(not running)
-            with open(path, "w", encoding="utf-8") as fh:
+        self.all_ports.setEnabled(not running)
-                fh.write(self.view.toPlainText())
+        self.refresh_btn.setEnabled(not running)
-
+        # Offline analysis would mix with the live session; disconnect first.
-    def _open_folder(self) -> None:
+        self.analyze_btn.setEnabled(not running)
-        self._session.root.mkdir(parents=True, exist_ok=True)
+        self._state_text = f"{state.value}" + (f" ({detail})" if detail else "")
-        QDesktopServices.openUrl(QUrl.fromLocalFile(str(self._session.root)))
+        self._update_status()
-
+
-    def shutdown(self) -> None:
+    def _update_status(self) -> None:
-        self._manager.disconnect()
+        sess = f"   |   Session log: {self._session.path}" if self._session.path else ""
-        self._session.stop()
+        c = self._counts
-
+        self.status.setText(
-
+            f"{getattr(self, '_state_text', '')}   |   boots seen: {c['boots']}   "
-class MainWindow(QMainWindow):
+            f"errors: {c['E']}   warnings: {c['W']}{sess}"
-    def __init__(self):
+        )
-        super().__init__()
+
-        self.setWindowTitle(f"KOTA Sensorbox Technician Tool  v{__version__}")
+    # ---- lines -------------------------------------------------------
-        self.resize(1200, 800)
+    def _on_line(self, line: LogLine) -> None:
-        tabs = QTabWidget()
+        self._session.write(line)
-        guide = QTextBrowser(openExternalLinks=True)
+        self._engine.feed(line)
-        guide.setHtml(cheatsheet_html())
+        self._runner.feed(line)
-        self.serial_tab = SerialTab()
+        self._diag_dirty = True
-        tabs.addTab(guide, "Quick start")
+        if line.kind == LineKind.BOOT:
-        tabs.addTab(self.serial_tab, "Serial monitor")
+            self._counts["boots"] += 1
-        self.setCentralWidget(tabs)
+        if line.level in ("E", "W"):
-
+            self._counts[line.level] += 1
-    def closeEvent(self, event):  # noqa: N802 (Qt naming)
+        self._update_status()
-        self.serial_tab.shutdown()
+
-        super().closeEvent(event)
+        allowed = LEVEL_FILTERS[self.filter_combo.currentText()]
+        if allowed is not None and line.kind != LineKind.HOST and not (
+            line.level in allowed or line.kind in (LineKind.PANIC, LineKind.BOOT, LineKind.RESET)
+        ):
+            return
+        self._append(line)
+
+    def _append(self, line: LogLine) -> None:
+        sb = self.view.verticalScrollBar()
+        at_bottom = sb.value() >= sb.maximum() - 4
+        fmt = QTextCharFormat()
+        fmt.setForeground(QColor(COLORS.get(line.level) or COLORS.get(line.kind, "#d4d4d4")))
+        if line.kind in (LineKind.PANIC, LineKind.BOOT, LineKind.HOST):
+            fmt.setFontWeight(QFont.Weight.Bold)
+        cur = QTextCursor(self.view.document())
+        cur.movePosition(QTextCursor.MoveOperation.End)
+        if not self.view.document().isEmpty():
+            cur.insertBlock()
+        cur.insertText(line.text, fmt)
+        if at_bottom:
+            sb.setValue(sb.maximum())
+
+    # ---- diagnostics -------------------------------------------------
+    def _refresh_diag(self) -> None:
+        if self._diag_dirty:
+            self._diag_dirty = False
+            self.diag.show_report(self._engine.report())
+        self.guide.refresh()   # countdowns and timeouts need a steady tick
+
+    # ---- guided troubleshooting hooks ------------------------------------
+    def _guide_action(self, action: str) -> bool:
+        if action == "reset" and self._manager.state == State.CONNECTED:
+            self._manager.reset_board()
+            return True
+        return False
+
+    def _guide_log(self, text: str) -> None:
+        # Technician answers go into the session log and the log view.
+        line = host_event(text)
+        self._session.write(line)
+        self._append(line)
+        self._diag_dirty = True
+
+    def _copy_report(self) -> None:
+        QGuiApplication.clipboard().setText(self._engine.report().to_text())
+
+    def _analyze_file(self) -> None:
+        path, _ = QFileDialog.getOpenFileName(
+            self, "Analyze log file", str(self._session.root), "Logs (*.log *.txt);;All files (*)")
+        if not path:
+            return
+        lines = read_log_file(Path(path))
+        self.view.clear()
+        self._engine.reset()
+        self._runner.cancel()
+        self._counts = {"E": 0, "W": 0, "boots": 0}
+        for line in lines:
+            self._engine.feed(line)
+            if line.kind == LineKind.BOOT:
+                self._counts["boots"] += 1
+            if line.level in ("E", "W"):
+                self._counts[line.level] += 1
+            self._append(line)
+        self._state_text = f"Analyzed file: {Path(path).name} ({len(lines)} lines)"
+        self._update_status()
+        self._diag_dirty = True
+        self._refresh_diag()
+
+    # ---- misc --------------------------------------------------------
+    def _save_view(self) -> None:
+        path, _ = QFileDialog.getSaveFileName(self, "Save log view", "sensorbox_log.txt", "Text (*.txt)")
+        if path:
+            with open(path, "w", encoding="utf-8") as fh:
+                fh.write(self.view.toPlainText())
+
+    def _open_folder(self) -> None:
+        self._session.root.mkdir(parents=True, exist_ok=True)
+        QDesktopServices.openUrl(QUrl.fromLocalFile(str(self._session.root)))
+
+    def shutdown(self) -> None:
+        self._manager.disconnect()
+        self._session.stop()
+
+
+class MainWindow(QMainWindow):
+    def __init__(self):
+        super().__init__()
+        self.setWindowTitle(f"KOTA Sensorbox Technician Tool  v{__version__}")
+        self.resize(1200, 800)
+        tabs = QTabWidget()
+        guide = QTextBrowser(openExternalLinks=True)
+        guide.setHtml(cheatsheet_html())
+        self.serial_tab = SerialTab()
+        self.flash_tab = FlashTab(self.serial_tab)
+        tabs.addTab(guide, "Quick start")
+        tabs.addTab(self.serial_tab, "Serial monitor")
+        tabs.addTab(self.flash_tab, "Flash firmware")
+        self.sd_tab = SdTab(self.serial_tab)
+        tabs.addTab(self.sd_tab, "SD card")
+        self.setCentralWidget(tabs)
+        settings_menu = self.menuBar().addMenu("Settings")
+        settings_menu.addAction("Service system address...", self._edit_service_base)
+
+    def _edit_service_base(self) -> None:
+        st = self.serial_tab
+        text, ok = QInputDialog.getText(
+            self, "Service system address",
+            "Address of the KOTA service system (the box MAC is added at the end):",
+            text=st._service_base())
+        if ok and text.strip().startswith(("https://", "http://")):
+            st._settings.setValue("service/base", text.strip())
+        elif ok:
+            QMessageBox.warning(self, "Service system address", "The address must start with https://")
+
+    def closeEvent(self, event):  # noqa: N802 (Qt naming)
+        self.serial_tab.shutdown()
+        super().closeEvent(event)

kota_tech/ui/matter_qr.py

@@ -0,0 +1,72 @@
+"""Matter pairing QR code on screen, so the technician can scan it from the laptop."""
+
+from __future__ import annotations
+
+import segno
+from PySide6.QtCore import Qt
+from PySide6.QtGui import QColor, QImage, QPainter, QPixmap
+from PySide6.QtWidgets import QDialog, QDialogButtonBox, QLabel, QVBoxLayout, QWidget
+
+from ..matter.payload import SetupPayload
+
+
+def qr_pixmap(text: str, size: int = 260) -> QPixmap:
+    """Black-on-white QR with the quiet zone phones need (4 modules)."""
+    qr = segno.make(text, error="m")
+    matrix = [list(row) for row in qr.matrix_iter(scale=1, border=4)]
+    n = len(matrix)
+    module = max(1, size // n)
+    img = QImage(n * module, n * module, QImage.Format.Format_RGB32)
+    img.fill(QColor("white"))
+    p = QPainter(img)
+    p.setPen(Qt.PenStyle.NoPen)
+    p.setBrush(QColor("black"))
+    for y, row in enumerate(matrix):
+        for x, dark in enumerate(row):
+            if dark:
+                p.drawRect(x * module, y * module, module, module)
+    p.end()
+    return QPixmap.fromImage(img)
+
+
+class MatterQrWidget(QWidget):
+    def __init__(self, payload: SetupPayload, size: int = 260, parent: QWidget | None = None):
+        super().__init__(parent)
+        self.image = QLabel()
+        self.image.setAlignment(Qt.AlignmentFlag.AlignCenter)
+        self.code = QLabel()
+        self.code.setAlignment(Qt.AlignmentFlag.AlignCenter)
+        self.code.setTextInteractionFlags(Qt.TextInteractionFlag.TextSelectableByMouse)
+        f = self.code.font()
+        f.setPointSize(f.pointSize() + 4)
+        f.setBold(True)
+        self.code.setFont(f)
+        self.note = QLabel(wordWrap=True)
+        self.note.setAlignment(Qt.AlignmentFlag.AlignCenter)
+        self.note.setStyleSheet("color:#555")
+        lay = QVBoxLayout(self)
+        lay.addWidget(self.image)
+        lay.addWidget(self.code)
+        lay.addWidget(self.note)
+        self._size = size
+        self.set_payload(payload)
+
+    def set_payload(self, payload: SetupPayload) -> None:
+        self.payload = payload
+        self.image.setPixmap(qr_pixmap(payload.qr_text(), self._size))
+        self.code.setText(f"Manual code: {payload.manual_code_pretty()}")
+        src = ("from this box's log" if payload.from_log else
+               "standard code of the v1.0 firmware - connect the box to confirm")
+        self.note.setText(f"Scan with the Matter app (Apple Home, Google Home, ...), or type the manual code. "
+                          f"Discriminator {payload.discriminator} ({src}). Same as the sticker on the box.")
+
+
+class MatterQrDialog(QDialog):
+    def __init__(self, payload: SetupPayload, parent: QWidget | None = None):
+        super().__init__(parent)
+        self.setWindowTitle("Matter pairing code")
+        lay = QVBoxLayout(self)
+        lay.addWidget(MatterQrWidget(payload, 320))
+        buttons = QDialogButtonBox(QDialogButtonBox.StandardButton.Close)
+        buttons.rejected.connect(self.reject)
+        lay.addWidget(buttons)

kota_tech/ui/sd_tab.py

@@ -0,0 +1,321 @@
+"""SD card tab: format a card for the sensorbox and write / check ENV.TXT."""
+
+from __future__ import annotations
+
+import threading
+from pathlib import Path
+
+from PySide6.QtCore import QObject, QSettings, Qt, Signal
+from PySide6.QtWidgets import (
+    QCheckBox,
+    QFileDialog,
+    QFormLayout,
+    QGroupBox,
+    QHBoxLayout,
+    QLabel,
+    QLineEdit,
+    QListWidget,
+    QListWidgetItem,
+    QMessageBox,
+    QPlainTextEdit,
+    QPushButton,
+    QVBoxLayout,
+    QWidget,
+)
+
+from ..sd.disks import Disk, list_cards
+from ..sd.envfile import EnvConfig, load_template
+from ..sd.provision import Outcome, check_card, format_and_write, write_env
+
+# The shared settings file the factory script uses, next to the tool folders.
+DEFAULT_TEMPLATE = Path(__file__).resolve().parents[4] / "002-SD_card_format" / "ENV.txt"
+
+
+class _Bridge(QObject):
+    done = Signal(object)
+    listed = Signal(object)
+
+
+def _secret_field() -> tuple[QLineEdit, QCheckBox]:
+    edit = QLineEdit()
+    edit.setEchoMode(QLineEdit.EchoMode.Password)
+    show = QCheckBox("show")
+    show.toggled.connect(lambda on: edit.setEchoMode(
+        QLineEdit.EchoMode.Normal if on else QLineEdit.EchoMode.Password))
+    return edit, show
+
+
+class SdTab(QWidget):
+    def __init__(self, serial_tab, parent: QWidget | None = None):
+        super().__init__(parent)
+        self.serial_tab = serial_tab
+        self._settings = QSettings("KOTA", "TechnicianTool")
+        self._cards: list[Disk] = []
+        self._busy = False
+        self._listing = False
+
+        # --- 1. settings
+        sbox = QGroupBox("1. Settings written to the card (ENV.TXT)")
+        self.template_label = QLabel(wordWrap=True)
+        load_btn = QPushButton("Load settings from ENV file...")
+        load_btn.clicked.connect(self._choose_template)
+        self.url = QLineEdit()
+        self.token, show_token = _secret_field()
+        form = QFormLayout()
+        form.addRow("INFLUX_URL", self.url)
+        trow = QHBoxLayout()
+        trow.addWidget(self.token, 1)
+        trow.addWidget(show_token)
+        form.addRow("INFLUX_TOKEN", trow)
+        self.wifi_box = QGroupBox("Local Wi-Fi instead of Matter (optional)")
+        self.wifi_box.setCheckable(True)
+        self.wifi_box.setChecked(False)
+        self.ssid = QLineEdit()
+        self.password, show_pw = _secret_field()
+        wform = QFormLayout(self.wifi_box)
+        wform.addRow("SSID", self.ssid)
+        prow = QHBoxLayout()
+        prow.addWidget(self.password, 1)
+        prow.addWidget(show_pw)
+        wform.addRow("PASSWORD", prow)
+        self.wifi_note = QLabel(wordWrap=True)
+        self.wifi_note.setStyleSheet("color:#555")
+        wform.addRow(self.wifi_note)
+        self.issues = QLabel(wordWrap=True)
+        sl = QVBoxLayout(sbox)
+        sl.addWidget(self.template_label)
+        sl.addWidget(load_btn, 0, Qt.AlignmentFlag.AlignLeft)
+        sl.addLayout(form)
+        sl.addWidget(self.wifi_box)
+        sl.addWidget(self.issues)
+
+        # --- 2. card
+        cbox = QGroupBox("2. SD card (inside the sensorbox case)")
+        self.card_list = QListWidget()
+        self.card_list.setMinimumHeight(80)
+        self.others = QLabel(wordWrap=True)
+        self.others.setStyleSheet("color:#666")
+        refresh = QPushButton("Refresh cards")
+        refresh.clicked.connect(self.refresh_cards)
+        cl = QVBoxLayout(cbox)
+        cl.addWidget(QLabel("Insert the card into the laptop's reader. Only removable cards are listed."))
+        cl.addWidget(self.card_list)
+        cl.addWidget(self.others)
+        cl.addWidget(refresh, 0, Qt.AlignmentFlag.AlignLeft)
+
+        # --- 3. actions
+        abox = QGroupBox("3. Action")
+        self.format_btn = QPushButton("Format card and write ENV.TXT")
+        self.format_btn.setMinimumHeight(34)
+        self.format_btn.setToolTip("Erases the card: FAT32 (MBR), label KOTA, then writes and verifies ENV.TXT")
+        self.write_btn = QPushButton("Write ENV.TXT only (keep card contents)")
+        self.write_btn.setToolTip("Keeps buffered measurements (BUFFER.TXT) on the card")
+        self.check_btn = QPushButton("Check card")
+        self.check_btn.setToolTip("Show what the box would read from this card")
+        self.format_btn.clicked.connect(self._format)
+        self.write_btn.clicked.connect(self._write_only)
+        self.check_btn.clicked.connect(self._check)
+        self.result = QLabel(wordWrap=True)
+        self.result.setTextFormat(Qt.TextFormat.RichText)
+        self.result.setMargin(8)
+        self.log = QPlainTextEdit(readOnly=True)
+        self.log.setMaximumBlockCount(500)
+        al = QVBoxLayout(abox)
+        for w in (self.format_btn, self.write_btn, self.check_btn, self.result, self.log):
+            al.addWidget(w)
+
+        left = QVBoxLayout()
+        left.addWidget(sbox)
+        left.addStretch(1)
+        right = QVBoxLayout()
+        right.addWidget(cbox)
+        right.addWidget(abox, 1)
+        lay = QHBoxLayout(self)
+        lay.addLayout(left, 1)
+        lay.addLayout(right, 1)
+
+        self._bridge = _Bridge()
+        self._bridge.done.connect(self._on_done)
+        self._bridge.listed.connect(self._on_listed)
+        for w in (self.url, self.token, self.ssid, self.password):
+            w.textChanged.connect(self._update)
+        self.wifi_box.toggled.connect(self._update)
+        self.card_list.currentRowChanged.connect(self._update)
+
+        path = Path(self._settings.value("sd/template", str(DEFAULT_TEMPLATE)))
+        self._load_template(path, quiet=True)
+        self._show_result("", "")
+        self._update()
+
+    # ---------------------------------------------------------- settings
+    def _choose_template(self) -> None:
+        path, _ = QFileDialog.getOpenFileName(self, "ENV file with the InfluxDB settings",
+                                              str(DEFAULT_TEMPLATE.parent), "Text (*.txt *.env);;All files (*)")
+        if path:
+            self._load_template(Path(path))
+
+    def _load_template(self, path: Path, quiet: bool = False) -> None:
+        try:
+            env = load_template(path)
+        except OSError as exc:
+            self.template_label.setText("No settings file loaded - load the ENV file the firmware team gave you.")
+            if not quiet:
+                QMessageBox.warning(self, "Cannot read file", str(exc))
+            return
+        self._settings.setValue("sd/template", str(path))
+        self.template_label.setText(f"Loaded from <code>{path}</code>")
+        self.url.setText(env.influx_url)
+        self.token.setText(env.influx_token)
+        # Wi-Fi is decided per box by the technician, never copied silently.
+        self._update()
+
+    def _env(self) -> EnvConfig:
+        wifi = self.wifi_box.isChecked()
+        return EnvConfig(self.url.text(), self.token.text(),
+                         self.ssid.text() if wifi else "", self.password.text() if wifi else "")
+
+    def _update(self) -> None:
+        env = self._env()
+        issues = env.problems()
+        colour = {"error": "#b03a2e", "warning": "#c77c02", "info": "#2e6da4"}
+        self.issues.setText("<br>".join(f"<span style='color:{colour[i.level]}'>{i.level.upper()}: {i.text}</span>"
+                                        for i in issues) or "<span style='color:#2e9e44'>Settings OK.</span>")
+        fw = self.serial_tab.engine.firmware
+        support = fw.supports_sd_wifi
+        self.wifi_note.setText(
+            "Only for boxes that should NOT use Matter. The box then joins this Wi-Fi directly. "
+            + {True: "The connected box's firmware supports this.",
+               False: "<b>The connected box runs the factory v1.0 firmware, which ignores these settings "
+                      "(it only uses Matter).</b> Newer firmware (after an OTA update) uses them.",
+               None: "Supported by newer firmware only; the factory v1.0 firmware ignores it."}[support])
+        errors = any(i.level == "error" for i in issues)
+        card = self._selected_card()
+        mounted = bool(card and card.volumes and card.volumes[0].mount)
+        self.format_btn.setEnabled(not self._busy and not errors and card is not None)
+        self.write_btn.setEnabled(not self._busy and not errors and mounted)
+        self.check_btn.setEnabled(not self._busy and mounted)
+
+    # -------------------------------------------------------------- cards
+    def showEvent(self, event):  # noqa: N802
+        self.refresh_cards()
+        super().showEvent(event)
+
+    def refresh_cards(self) -> None:
+        """List cards in the background: the UI never waits for a slow card reader."""
+        if self._busy or self._listing:
+            return
+        self._listing = True
+        self.others.setText("Looking for SD cards...")
+
+        def worker():
+            try:
+                result = list_cards()
+            except Exception as exc:        # show it, never leave the tab stuck
+                result = ([], [], str(exc))
+            self._bridge.listed.emit(result)
+
+        threading.Thread(target=worker, daemon=True, name="sd-list").start()
+
+    def _on_listed(self, result) -> None:
+        self._listing = False
+        self._cards, others = result[0], result[1]
+        if len(result) > 2:
+            self.others.setText(f"Could not list cards: {result[2]}")
+            self._update()
+            return
+        self.card_list.clear()
+        for d in self._cards:
+            self.card_list.addItem(QListWidgetItem(d.label))
+        if self._cards:
+            self.card_list.setCurrentRow(0)
+        empty = [d for d in others if not d.has_media]
+        big = [d for d in others if d.has_media]
+        notes = []
+        if empty:
+            notes.append("Card reader found but no card inserted: " + ", ".join(d.name for d in empty) + ".")
+        if big:
+            notes.append("Not offered (too large to be an SD card): " + ", ".join(d.label for d in big) + ".")
+        if not self._cards and not empty:
+            notes.append("No SD card or card reader found.")
+        self.others.setText(" ".join(notes))
+        self._update()
+
+    def _selected_card(self) -> Disk | None:
+        i = self.card_list.currentRow()
+        return self._cards[i] if 0 <= i < len(self._cards) else None
+
+    # ------------------------------------------------------------ actions
+    def _format(self) -> None:
+        card = self._selected_card()
+        if card is None:
+            return
+        box = QMessageBox(QMessageBox.Icon.Warning, "Format SD card",
+                          f"ALL DATA ON THIS CARD WILL BE ERASED:\n\n{card.label}\n\n"
+                          "Buffered measurements on the card are lost too. Continue?",
+                          QMessageBox.StandardButton.Cancel, self)
+        erase = box.addButton("Erase and format", QMessageBox.ButtonRole.DestructiveRole)
+        box.exec()
+        if box.clickedButton() is not erase:
+            return
+        env = self._env()
+        self._run(lambda: format_and_write(card, env), f"Formatting {card.name}...")
+
+    def _write_only(self) -> None:
+        card = self._selected_card()
+        if card and card.volumes:
+            env, mount = self._env(), card.volumes[0].mount
+            self._run(lambda: write_env(mount, env), f"Writing ENV.TXT to {mount}...")
+
+    def _check(self) -> None:
+        card = self._selected_card()
+        if not (card and card.volumes):
+            return
+        vol = card.volumes[0]
+        rep = check_card(vol.mount, vol.filesystem)
+        lines = [f"Card {vol.mount} ({vol.filesystem or '?'})"]
+        if rep.env:
+            lines += [f"  {k}={v}" for k, v in rep.env.masked().items()]
+            lines += [f"  {i.level.upper()}: {i.text}" for i in rep.env.issues]
+        lines += [f"  PROBLEM: {p}" for p in rep.problems]
+        if rep.buffered_lines is not None:
+            lines.append(f"  {rep.buffered_lines} measurement lines buffered on the card, waiting for upload.")
+        self.log.appendPlainText("\n".join(lines))
+        ok = not rep.problems and rep.env is not None and rep.env.ok
+        self._show_result("Card is OK for the sensorbox." if ok else "Card has problems - see below. "
+                          "Use 'Write ENV.TXT only' or 'Format card'.", "ok" if ok else "error")
+
+    def _run(self, job, what: str) -> None:
+        self._busy = True
+        self._update()
+        self._show_result(what, "info")
+
+        def worker():
+            try:
+                out = job()
+            except Exception as exc:   # report, never leave the tab busy
+                out = Outcome(False, f"Unexpected error: {exc}")
+            self._bridge.done.emit(out)
+
+        threading.Thread(target=worker, daemon=True).start()
+
+    def _on_done(self, out: Outcome) -> None:
+        self._busy = False
+        for line in out.log:
+            self.log.appendPlainText(line)
+        self.log.appendPlainText(out.message)
+        if out.ok:
+            self._show_result(f"<b>{out.message}</b><br>Insert the next card and press Refresh cards to "
+                              "provision another one.", "ok")
+        else:
+            self._show_result(f"<b>{out.message}</b>", "error")
+        self.refresh_cards()
+
+    def _show_result(self, html: str, kind: str) -> None:
+        colours = {"ok": ("#2e9e44", "#e3f4e7"), "info": ("#2e6da4", "#e3edf7"), "error": ("#d9534f", "#f9e0df")}
+        self.result.setVisible(bool(html))
+        if html:
+            border, bg = colours[kind]
+            self.result.setStyleSheet(f"QLabel {{ border:2px solid {border}; background:{bg}; border-radius:6px; }}")
+            self.result.setText(html)
+
+

pyproject.toml

@@ -1,15 +1,17 @@
 [project]
 name = "kota-technician-tool"
-version = "0.2.0"
+version = "0.6.0"
 description = "KOTA sensorbox technician diagnostic tool (demo)"
 requires-python = ">=3.11,<3.14"
 dependencies = [
     "pyserial>=3.5",
     "PySide6-Essentials>=6.7",
+    "esptool~=4.8",   # 4.x CLI (write_flash/read_flash); v5 renamed commands
+    "segno>=1.6",     # QR code for Matter pairing (pure Python)
 ]
 
 [dependency-groups]
-dev = ["pytest>=8"]
+dev = ["pytest>=8", "pyfatfs>=1.0", "setuptools<81"]   # pyfatfs (independent FAT32 check) needs pkg_resources
 
 [tool.uv]
 package = false

run_macos.command

@@ -3,7 +3,7 @@
 cd "$(dirname "$0")" || exit 1
 
 # Keep the virtual environment out of the (Google Drive) tool folder.
-export UV_PROJECT_ENVIRONMENT="$HOME/Library/Caches/KotaTechnicianTool/venv-0.2"
+export UV_PROJECT_ENVIRONMENT="$HOME/Library/Caches/KotaTechnicianTool/venv-0.6"
 export PATH="$HOME/.local/bin:$PATH"
 
 if ! command -v uv >/dev/null 2>&1; then

run_windows.bat

@@ -3,7 +3,7 @@ setlocal
 cd /d "%~dp0"
 
 rem Keep the virtual environment out of the (Google Drive) tool folder.
-set "UV_PROJECT_ENVIRONMENT=%LOCALAPPDATA%\KotaTechnicianTool\venv-0.2"
+set "UV_PROJECT_ENVIRONMENT=%LOCALAPPDATA%\KotaTechnicianTool\venv-0.6"
 set "PATH=%USERPROFILE%\.local\bin;%PATH%"
 
 where uv >nul 2>nul

tests/test_fat32.py

@@ -0,0 +1,103 @@
+"""FAT32/MBR layout: field-level checks against the FAT spec on an in-memory
+disk, plus an independent FAT implementation (pyfatfs) mounting the result."""
+
+import struct
+
+import pytest
+
+from kota_tech.sd import fat32
+
+MiB, GiB = 1024**2, 1024**3
+
+
+def make_disk(size: int, label="KOTA") -> tuple[bytearray, fat32.Fat32Layout]:
+    lay = fat32.plan(size)
+    disk = bytearray(b"\xAA" * size)                # old garbage everywhere
+    zeros, writes = fat32.build(lay, label, 0x12345678, 0xCAFEBABE, size)
+    for off, n in zeros:
+        disk[off:off + n] = bytes(n)
+    for off, data in writes:
+        disk[off:off + len(data)] = data
+    return disk, lay
+
+
+@pytest.fixture(scope="module")
+def small():
+    return make_disk(96 * MiB)
+
+
+def test_mbr_has_one_fat32_lba_partition(small):
+    disk, lay = small
+    assert disk[510:512] == b"\x55\xAA"
+    status, ptype, lba, count = struct.unpack_from("<B3xB3xII", disk, 0x1BE)
+    assert (status, ptype, lba) == (0, 0x0C, fat32.PART_START // 512)
+    assert count == lay.part_sectors
+    assert disk[0x1CE:0x1FE] == bytes(48)                    # other entries empty
+    assert struct.unpack_from("<I", disk, 0x1B8)[0] == 0xCAFEBABE
+
+
+def test_boot_sector_fields(small):
+    disk, lay = small
+    b = disk[fat32.PART_START:fat32.PART_START + 512]
+    bps, spc, rsvd, nfats, root_ent, tot16, media, fat16 = struct.unpack_from("<HBHBHHBH", b, 11)
+    assert (bps, spc, rsvd, nfats, root_ent, tot16, media, fat16) == (512, lay.sectors_per_cluster, 32, 2, 0, 0, 0xF8, 0)
+    hidden, tot32, fatsz, _, _, root_clus, fsinfo, bkboot = struct.unpack_from("<IIIHHIHH", b, 28)
+    assert hidden == fat32.PART_START // 512 and tot32 == lay.part_sectors and fatsz == lay.fat_sectors
+    assert (root_clus, fsinfo, bkboot) == (2, 1, 6)
+    assert b[66] == 0x29 and b[71:82] == b"KOTA       " and b[82:90] == b"FAT32   " and b[510:] == b"\x55\xAA"
+    assert disk[fat32.PART_START + 6 * 512:fat32.PART_START + 7 * 512] == b          # backup boot sector
+
+
+def test_fat_is_large_enough_and_clusters_valid(small):
+    _, lay = small
+    assert fat32.MIN_CLUSTERS <= lay.clusters
+    assert lay.fat_sectors * 512 // 4 >= lay.clusters + 2
+    assert lay.data_start + lay.clusters * lay.sectors_per_cluster <= lay.part_sectors
+
+
+def test_fsinfo_and_fat_entries(small):
+    disk, lay = small
+    info = disk[fat32.PART_START + 512:fat32.PART_START + 1024]
+    assert struct.unpack_from("<I", info, 0)[0] == 0x41615252
+    assert struct.unpack_from("<III", info, 484) == (0x61417272, lay.clusters - 1, 3)
+    assert struct.unpack_from("<I", info, 508)[0] == 0xAA550000
+    for fat in range(2):
+        off = fat32.PART_START + (32 + fat * lay.fat_sectors) * 512
+        assert struct.unpack_from("<III", disk, off) == (0x0FFFFFF8, 0x0FFFFFFF, 0x0FFFFFFF)
+        assert disk[off + 12:off + lay.fat_sectors * 512] == bytes(lay.fat_sectors * 512 - 12)
+
+
+def test_root_holds_only_the_label(small):
+    disk, lay = small
+    root = fat32.PART_START + lay.data_start * 512
+    assert disk[root:root + 11] == b"KOTA       " and disk[root + 11] == 0x08
+    assert disk[root + 32:root + lay.sectors_per_cluster * 512] == bytes(lay.sectors_per_cluster * 512 - 32)
+
+
+@pytest.mark.parametrize("size,spc", [(4 * GiB, 8), (15 * GiB, 16), (31_457_280_000, 32), (64 * GiB, 32)])
+def test_real_card_sizes(size, spc):
+    lay = fat32.plan(size)
+    assert lay.sectors_per_cluster == spc
+    assert lay.part_sectors * 512 <= min(size - fat32.PART_START, 32 * GiB)
+    assert fat32.MIN_CLUSTERS <= lay.clusters < fat32.MAX_CLUSTERS
+
+
+def test_too_small_card_refused():
+    with pytest.raises(ValueError):
+        fat32.plan(20 * MiB)
+
+
+def test_independent_fat_implementation_mounts_it(small, tmp_path):
+    pyfat = pytest.importorskip("pyfatfs.PyFat")
+    disk, lay = small
+    img = tmp_path / "part.img"
+    img.write_bytes(bytes(disk[fat32.PART_START:fat32.PART_START + lay.part_sectors * 512]))
+    fs = pyfat.PyFat()
+    fs.open(str(img))
+    assert fs.fat_type == pyfat.PyFat.FAT_TYPE_FAT32
+    assert fs.bpb_header["BPB_TotSec32"] == lay.part_sectors
+    fs.close()
+    from pyfatfs.PyFatFS import PyFatFS
+    with PyFatFS(str(img)) as ffs:                       # write + read back a file like ENV.TXT
+        ffs.writebytes("/ENV.TXT", b"INFLUX_URL=x\n")
+        assert ffs.readbytes("/ENV.TXT") == b"INFLUX_URL=x\n"

tests/test_flash.py

@@ -0,0 +1,274 @@
+"""Flashing: image validation on the real official image, plan building,
+and the runner against a fake esptool (no hardware)."""
+
+import hashlib
+import sys
+import threading
+from pathlib import Path
+
+import pytest
+
+from kota_tech.flash.image import ImageError, inspect_image, official_images
+from kota_tech.flash.plan import Mode, build_plan, check_partition_table
+from kota_tech.flash.runner import FlashRunner
+
+FW = Path(__file__).resolve().parents[1] / "firmware" / "new_system.bin"
+
+
+@pytest.fixture(scope="module")
+def image():
+    imgs = official_images()
+    assert len(imgs) == 1
+    return imgs[0]
+
+
+# ------------------------------------------------------------------ image
+
+def test_official_image_is_the_deployed_v1_build(image):
+    assert image.app.project == "kota-sensorboard"
+    assert image.app.elf_sha.startswith("45fa9d5b9")       # same as the live board
+    assert image.flash_size == "8MB"
+    assert image.partition("ota_0").offset == 0x40000
+    assert image.partition("otadata").offset == 0x31000
+    assert image.partition("nvs").offset == 0x10000
+
+
+def test_app_bytes_are_a_complete_app_image(image):
+    app = image.app_bytes()
+    assert app[0] == 0xE9
+    assert len(app) == len(image.data) - 0x40000              # ends where the file ends
+    assert len(image.blank_otadata()) == 0x2000 and set(image.blank_otadata()) == {0xFF}
+
+
+def test_modified_image_is_refused(tmp_path):
+    data = bytearray(FW.read_bytes())
+    data[-1] ^= 0xFF
+    bad = tmp_path / "new_system.bin"
+    bad.write_bytes(data)
+    manifest = tmp_path / "firmware.toml"
+    manifest.write_text(f'[[image]]\nfile = "new_system.bin"\nsha256 = "{hashlib.sha256(FW.read_bytes()).hexdigest()}"\n')
+    with pytest.raises(ImageError, match="SHA-256"):
+        official_images(manifest)
+
+
+@pytest.mark.parametrize("patch,msg", [
+    ((0, 0x00), "not an ESP32 firmware"),
+    ((12, 0x05), "not ESP32-S3"),
+])
+def test_wrong_images_are_rejected(tmp_path, patch, msg):
+    data = bytearray(FW.read_bytes())
+    data[patch[0]] = patch[1]
+    p = tmp_path / "x.bin"
+    p.write_bytes(data)
+    with pytest.raises(ImageError, match=msg):
+        inspect_image(p)
+
+
+# ------------------------------------------------------------------- plan
+
+def test_app_only_plan_keeps_nvs(image, tmp_path):
+    plan = build_plan(image, Mode.APP_ONLY, "COM5", tmp_path)
+    kinds = [s.kind for s in plan.steps]
+    assert kinds == ["read_pt", "write"]
+    write = plan.steps[-1].args
+    offsets = [a for a in write if a.startswith("0x")]
+    assert offsets == ["0x31000", "0x40000"]          # otadata + ota_0 only
+    assert "0x10000" not in write and "0x0" not in write   # NVS / bootloader untouched
+    assert write[write.index("--after") + 1] == "hard_reset"
+    assert (tmp_path / "app_ota0.bin").read_bytes() == image.app_bytes()
+
+
+def test_full_plan_with_backup(image, tmp_path):
+    backup = tmp_path / "bk.bin"
+    plan = build_plan(image, Mode.FULL, "COM5", tmp_path, backup_to=backup)
+    assert [s.kind for s in plan.steps] == ["backup", "write"]
+    assert plan.steps[0].args[-3:] == ["0", "0x800000", str(backup)]
+    assert plan.steps[0].args[plan.steps[0].args.index("--after") + 1] == "no_reset"
+    assert plan.steps[1].args[-2:] == ["0x0", str(image.path)]
+    assert "Back up" in plan.summary()[0]
+
+
+def test_partition_table_check(image):
+    assert check_partition_table(image.partition_table, image) is None
+    assert "blank" in check_partition_table(b"\xff" * 0xC00, image)
+    other = bytearray(image.partition_table)
+    other[40] ^= 1
+    assert "different partition layout" in check_partition_table(bytes(other), image)
+
+
+# ----------------------------------------------------------------- runner
+
+FAKE = """
+import sys, pathlib
+args = sys.argv[1:]
+if "read_flash" in args:
+    out = pathlib.Path(args[-1])
+    src = pathlib.Path(r"{fw}").read_bytes()
+    off, size = int(args[-3], 0), int(args[-2], 0)
+    {pt_line}
+    print("Read ... (50 %)", end="\\r"); print("Read ... (100 %)")
+    sys.exit(0)
+if "write_flash" in args:
+    for p in (10, 60, 100):
+        print(f"Writing at 0x00040000... ({{p}} %)", end="\\r", flush=True)
+    print(); print("Hash of data verified.")
+    sys.exit({write_code})
+"""
+
+
+def _fake(tmp_path, write_code=0, pt="same", fail_text=""):
+    pt_line = {"same": "out.write_bytes(src[off:off+size])",
+               "blank": "out.write_bytes(b'\\xff' * size)"}[pt]
+    script = FAKE.format(fw=FW, pt_line=pt_line, write_code=write_code)
+    if fail_text:
+        script = script.replace('print("Hash of data verified.")', f'print("{fail_text}")')
+    f = tmp_path / "fake_esptool.py"
+    f.write_text(script)
+    return [sys.executable, str(f)]
+
+
+def _run(plan, cmd):
+    steps, progress, output, done = [], [], [], threading.Event()
+    result = {}
+    r = FlashRunner(plan, lambda i, t: steps.append(i), progress.append, output.append,
+                    lambda res: (result.setdefault("r", res), done.set()), esptool_cmd=cmd)
+    r.start()
+    assert done.wait(30)
+    return result["r"], steps, progress, output
+
+
+def test_runner_app_only_success(image, tmp_path):
+    plan = build_plan(image, Mode.APP_ONLY, "COM5", tmp_path)
+    res, steps, progress, output = _run(plan, _fake(tmp_path))
+    assert res.ok, res
+    assert steps == [0, 1]
+    assert 60 in progress and progress[-1] == 100
+    assert any("Hash of data verified" in o for o in output)
+
+
+def test_runner_refuses_app_only_on_blank_chip(image, tmp_path):
+    plan = build_plan(image, Mode.APP_ONLY, "COM5", tmp_path)
+    res, steps, *_ = _run(plan, _fake(tmp_path, pt="blank"))
+    assert not res.ok and "Full mode" in res.message
+    assert steps == [0]                       # never reached the write step
+
+
+def test_runner_reports_connect_failure_with_hint(image, tmp_path):
+    plan = build_plan(image, Mode.FULL, "COM5", tmp_path)
+    cmd = _fake(tmp_path, write_code=2,
+                fail_text="A fatal error occurred: Failed to connect to ESP32-S3: No serial data received.")
+    res, *_ = _run(plan, cmd)
+    assert not res.ok and res.failed_step == 0
+    assert "BOOT" in res.hint
+
+
+# ------------------------------------------------- developer builds (v0.5)
+
+from kota_tech.flash.image import FirmwareLibrary, app_image_length  # noqa: E402
+
+
+def _app_only_file(image, tmp_path, name="kota-sensorboard.bin"):
+    p = tmp_path / name
+    p.write_bytes(image.app_bytes())          # what a developer build/ folder contains
+    return p
+
+
+def test_integrity_check_on_factory_image(image):
+    d = image.data
+    assert app_image_length(d, 0) > 0                          # bootloader
+    assert app_image_length(d, 0x40000) == len(d) - 0x40000    # app ends exactly at file end
+
+
+@pytest.mark.parametrize("damage,msg", [
+    (lambda b: b[:len(b) // 2], "truncated"),
+    (lambda b: b[:0x40000 + 5000] + bytes([b[0x40000 + 5000] ^ 1]) + b[0x40000 + 5001:], "corrupted"),
+])
+def test_corrupted_or_truncated_images_refused(tmp_path, damage, msg):
+    p = tmp_path / "broken.bin"
+    p.write_bytes(damage(FW.read_bytes()))
+    with pytest.raises(ImageError, match=msg):
+        inspect_image(p, origin="developer")
+
+
+def test_import_app_only_developer_build(image, tmp_path):
+    lib = FirmwareLibrary(tmp_path / "lib")
+    src = _app_only_file(image, tmp_path)
+    img = lib.import_file(src, reference=image)
+    assert img.is_developer and img.kind == "app"
+    assert img.partition("ota_0").offset == 0x40000            # layout from the factory image
+    assert img.app_bytes() == image.app_bytes()
+    listed, problems = lib.images(image)
+    assert [i.sha256 for i in listed] == [img.sha256] and problems == []
+    assert lib.import_file(src, reference=image).sha256 == img.sha256   # re-import: no duplicate
+    assert len(lib.images(image)[0]) == 1
+
+
+def test_app_only_build_cannot_be_flashed_full(image, tmp_path):
+    lib = FirmwareLibrary(tmp_path / "lib")
+    img = lib.import_file(_app_only_file(image, tmp_path), reference=image)
+    plan = build_plan(img, Mode.APP_ONLY, "COM5", tmp_path / "w")
+    assert [s.kind for s in plan.steps] == ["read_pt", "write"]
+    with pytest.raises(ValueError, match="app only"):
+        build_plan(img, Mode.FULL, "COM5", tmp_path / "w")
+
+
+def test_import_merged_developer_build(image, tmp_path):
+    lib = FirmwareLibrary(tmp_path / "lib")
+    src = tmp_path / "dev_full.bin"
+    src.write_bytes(image.data)
+    img = lib.import_file(src, reference=image)
+    assert img.kind == "merged" and img.is_developer
+    assert [s.kind for s in build_plan(img, Mode.FULL, "COM5", tmp_path / "w").steps] == ["write"]
+
+
+def test_library_detects_file_changed_after_import(image, tmp_path):
+    lib = FirmwareLibrary(tmp_path / "lib")
+    img = lib.import_file(_app_only_file(image, tmp_path), reference=image)
+    stored = tmp_path / "lib" / img.path.name
+    data = bytearray(stored.read_bytes())
+    data[-40] ^= 1
+    stored.write_bytes(data)
+    listed, problems = lib.images(image)
+    assert listed == [] and problems
+
+
+def test_library_remove(image, tmp_path):
+    lib = FirmwareLibrary(tmp_path / "lib")
+    img = lib.import_file(_app_only_file(image, tmp_path), reference=image)
+    lib.remove(img.sha256)
+    assert lib.images(image) == ([], []) and not img.path.exists()
+
+
+def test_non_firmware_file_refused(tmp_path, image):
+    p = tmp_path / "notes.bin"
+    p.write_bytes(b"hello firmware team")
+    with pytest.raises(ImageError, match="not an ESP32 firmware"):
+        FirmwareLibrary(tmp_path / "lib").import_file(p, reference=image)
+
+
+# ------------------------------------------- bundled developer build (v0.6)
+
+from kota_tech.flash.image import bundled_images  # noqa: E402
+
+
+def test_bundled_developer_build_is_labelled_and_not_default():
+    imgs = bundled_images()
+    assert [i.origin for i in imgs] == ["factory", "developer"]       # factory first
+    dev = imgs[1]
+    assert dev.built_by == "Krzysztof Kallas" and "built by Krzysztof Kallas" in dev.label()
+    assert dev.kind == "merged" and dev.app.elf_sha.startswith("c94ba0e9b")
+    assert dev.partition_table == imgs[0].partition_table            # App-only safe on v1.0 boxes
+    assert [i.origin for i in factory_images_only()] == ["factory"]
+
+
+def factory_images_only():
+    from kota_tech.flash.image import factory_images
+    return factory_images()
+
+
+def test_import_records_who_built_it(image, tmp_path):
+    lib = FirmwareLibrary(tmp_path / "lib")
+    img = lib.import_file(_app_only_file(image, tmp_path), reference=image, built_by="  Anna Nowak ")
+    assert img.built_by == "Anna Nowak" and "built by Anna Nowak" in img.label()
+    again, _ = lib.images(image)
+    assert again[0].built_by == "Anna Nowak"

tests/test_guides.py

@@ -0,0 +1,244 @@
+"""Guided troubleshooting: runner + engine with simulated technician
+answers, simulated board output and a fake clock."""
+
+from pathlib import Path
+
+import pytest
+
+from kota_tech.core.logfile import read_log_file
+from kota_tech.core.logline import parse_line
+from kota_tech.diag.engine import DiagnosticsEngine, Severity
+from kota_tech.diag.guides import LED_ANSWERS, GuideRunner, load_guides, recommended
+
+FIX = Path(__file__).parent / "fixtures"
+BOOT = ["ESP-ROM:esp32s3-20210327", "rst:0x1 (POWERON),boot:0x8 (SPI_FAST_FLASH_BOOT)",
+        "I (1299) app_init: Project name:     kota-sensorboard",
+        "I (1317) app_init: ELF file SHA256:  45fa9d5b9..."]
+
+
+class Clock:
+    def __init__(self):
+        self.t = 1000.0
+
+    def __call__(self):
+        return self.t
+
+
+@pytest.fixture
+def rig():
+    engine, clock, actions, log = DiagnosticsEngine(), Clock(), [], []
+    runner = GuideRunner(engine, on_action=lambda a: actions.append(a) or True,
+                         on_log=log.append, clock=clock)
+
+    def board(*lines):
+        for ln in lines:
+            parsed = parse_line(ln)
+            engine.feed(parsed)
+            runner.feed(parsed)
+
+    return engine, runner, clock, actions, board, log
+
+
+def _bench(engine):
+    for ln in read_log_file(FIX / "live_boot_A4CB8FC946F8_fw1.0.txt"):
+        engine.feed(ln)
+
+
+def test_all_guides_load_and_validate():
+    guides = load_guides()
+    assert "quick" in guides and len(guides) >= 8
+    led = guides["quick"].steps["led"]
+    assert set(led.route) == set(LED_ANSWERS)   # every colour has a route
+
+
+def test_recommendations_follow_findings(rig):
+    engine, *_ = rig
+    _bench(engine)
+    ids = [g.id for g in recommended(load_guides(), engine)]
+    assert ids[0] == "quick"
+    assert ids.index("network") < ids.index("clock")    # root order preserved
+    assert "mic" in ids
+
+
+def test_purple_uncommissioned_box_skips_to_pairing_and_follows_it_live(rig):
+    engine, runner, clock, _, board, log = rig
+    _bench(engine)                               # log: not commissioned, LED purple
+    runner.start("quick")
+    runner.answer("PURPLE")
+    # "Was it paired before?" is skipped: the log already shows it is not.
+    assert runner.step.id == "pair_intro"
+    runner.proceed()
+    assert runner.view().waiting and runner.step.id == "pair_start"
+    board("I (90000) MAIN: Commissioning session started")
+    assert runner.step.id == "pair_wifi"
+    board("I (95000) MAIN: Commissioning complete")
+    assert runner.step.id == "pair_time"
+    board("I (99000) SNTP: Time synchronized: Sat Sep 26 16:00:00 2026")
+    assert runner.step.id == "pair_upload"
+    board("I (120000) INFLUX: HTTP request performed, status code: 204")
+    assert runner.end.id == "online" and runner.end.severity == "ok"
+    assert any("Paired" in t or "paired" in t for t in engine.technician)
+    assert "matter.not_commissioned" not in {rc.finding.rule_id for rc in engine.report().roots}
+    assert any(l.startswith("technician:") for l in log)
+
+
+def test_pairing_timeout_asks_what_the_app_shows(rig):
+    engine, runner, clock, _, board, _ = rig
+    _bench(engine)
+    runner.start("network")
+    runner.proceed()                             # pair_intro -> pair_start
+    clock.t += 301
+    runner.tick()
+    assert runner.step.id == "not_found"
+    runner.answer("1")
+    assert runner.end.id == "ble_not_found"
+    f = engine.findings["tech.network.ble_not_found"]
+    assert f.severity == Severity.ERROR and f.active
+
+
+def test_led_mismatch_is_recorded(rig):
+    engine, runner, *_ = rig
+    _bench(engine)                               # log implies PURPLE
+    runner.start("quick")
+    runner.answer("GREEN")
+    f = engine.findings["tech.led_mismatch"]
+    assert "Green" in f.title and "Purple" in f.title
+    assert runner.step.id == "heartbeat"
+
+
+def test_led_match_records_nothing(rig):
+    engine, runner, *_ = rig
+    _bench(engine)
+    runner.start("quick")
+    runner.answer("PURPLE")
+    assert "tech.led_mismatch" not in engine.findings
+
+
+def test_blue_reseat_fixed_after_power_cycle(rig):
+    engine, runner, clock, _, board, _ = rig
+    board(*BOOT, "E (3511) MAIN: Failed to initialize RTC: ESP_ERR_TIMEOUT")
+    runner.start("quick")
+    runner.answer("BLUE")
+    runner.proceed()
+    runner.proceed()                             # -> verify (technician power-cycles)
+    assert runner.step.id == "verify"
+    board(*BOOT, "I (14800) temperature_sensor: Range [20°C ~ 100°C], error < 2°C")
+    assert runner.end.id == "i2c_fixed"
+
+
+def test_blue_still_failing_then_module(rig):
+    engine, runner, clock, _, board, _ = rig
+    board(*BOOT, "E (3511) MAIN: Failed to initialize RTC: ESP_ERR_TIMEOUT")
+    runner.start("rtc_i2c")
+    runner.proceed()
+    runner.proceed()
+    board(*BOOT, "E (3511) MAIN: Failed to initialize RTC: ESP_ERR_TIMEOUT")
+    assert runner.step.id == "damaged"
+    runner.answer("1")
+    assert runner.end.id == "rtc_module"
+
+
+def test_white_skips_portal_question_on_v1_firmware(rig):
+    engine, runner, clock, _, board, _ = rig
+    board(*BOOT)                                 # known v1.0: no setup portal
+    runner.start("white")
+    runner.answer("1")                           # nobody held the button
+    assert runner.step.id == "sd_reseat"
+
+
+def test_white_asks_portal_question_on_unknown_firmware(rig):
+    engine, runner, clock, _, board, _ = rig
+    board("ESP-ROM:esp32s3-20210327", "I (1317) app_init: ELF file SHA256:  0123456789...")
+    runner.start("white")
+    runner.answer("1")
+    assert runner.step.id == "portal"
+
+
+def test_red_routes_to_failing_sensor_and_names_it(rig):
+    engine, runner, clock, _, board, _ = rig
+    board(*BOOT, "E (14000) MAIN: Failed to initialize SEN66: ESP_ERR_TIMEOUT")
+    runner.start("sensors")
+    assert runner.step.id == "reseat"
+    assert "SEN66" in runner.view().text
+    runner.proceed()
+    board(*BOOT, "E (14000) MAIN: Failed to initialize SEN66: ESP_ERR_TIMEOUT")
+    assert runner.end.id == "sensor_replace"
+
+
+def test_reboot_loop_resets_board_then_routes_by_cause(rig):
+    engine, runner, clock, actions, board, _ = rig
+    runner.start("reboot_loop")
+    assert actions == ["reset"]
+    board(*BOOT, "E (1519) SD_CARD: Failed to initialize the card (ESP_ERR_TIMEOUT). x")
+    clock.t += 46
+    runner.tick()
+    assert runner.guide.id == "white"
+
+
+def test_reset_action_failure_is_shown(rig):
+    engine = DiagnosticsEngine()
+    runner = GuideRunner(engine, on_action=lambda a: False, clock=Clock())
+    runner.start("reboot_loop")
+    assert "connect" in runner.view().note.lower()
+
+
+def test_mic_switch_flip_verified_without_restart(rig):
+    engine, runner, clock, actions, board, _ = rig
+    _bench(engine)
+    runner.start("mic")
+    assert runner.step.id == "switch"
+    assert "above the power switch" in runner.view().text
+    runner.answer("0")                           # flipped the external switch
+    assert actions == []                         # the firmware re-reads it; no reset
+    board("I (95000) MICROPHONE: Read 300000 bytes in 4936 ms")
+    assert runner.end.id == "mic_on"
+
+
+def test_mic_switch_no_effect_in_both_positions(rig):
+    engine, runner, clock, actions, board, _ = rig
+    _bench(engine)
+    runner.start("mic")
+    runner.answer("0")
+    board("W (95000) MICROPHONE: Microphone is in shutdown state, skipping sample collection")
+    assert runner.step.id == "flip_back"
+    runner.answer("0")
+    board("W (105000) MICROPHONE: Microphone is in shutdown state, skipping sample collection")
+    assert runner.end.id == "mic_switch_faulty"
+
+
+def test_mic_clap_test_detects_dead_mic(rig):
+    engine, runner, clock, _, board, _ = rig
+    board(*BOOT, *["I (20036) MICROPHONE: Sum SQ: 0.000000, RMS pressure: 0.000000, "
+                   "Normalized: 0.000000, dB peak: -inf"] * 2)
+    runner.start("mic")
+    assert runner.step.id == "clap"
+    board("I (30036) MICROPHONE: Sum SQ: 0.000000, RMS pressure: 0.000000, Normalized: 0.000000, dB peak: -inf")
+    clock.t += 46
+    runner.tick()
+    assert runner.end.id == "mic_faulty"
+
+
+def test_mic_clap_test_passes_on_sound(rig):
+    engine, runner, clock, _, board, _ = rig
+    runner.start("mic")
+    board("I (30036) MICROPHONE: Sum SQ: 12.5, RMS pressure: 0.02, Normalized: 0.1, dB peak: 71.3")
+    assert runner.end.id == "mic_ok"
+
+
+def test_back_never_reenters_a_wait(rig):
+    engine, runner, clock, actions, board, _ = rig
+    runner.start("sensors")                      # route -> capture (wait, resets board)
+    assert runner.step.id == "capture" and actions == ["reset"]
+    clock.t += 46
+    runner.tick()                                # -> which_again -> end:red_unclear
+    runner.back()
+    assert actions == ["reset"]                  # no second reset
+
+
+def test_skip_wait_and_report_contains_technician_checks(rig):
+    engine, runner, clock, _, board, _ = rig
+    runner.start("update")
+    runner.proceed()                             # technician skips the wait
+    assert runner.end.id == "update_slow"
+    text = engine.report().to_text()
+    assert "Technician checks:" in text and "Update is taking very long" in text

tests/test_matter.py

@@ -0,0 +1,42 @@
+"""Matter onboarding payload, checked against the real sticker of the bench box
+(QR decoded from matter_commissioning_qr.png: MT:Y.K9042C00KA0648G00)."""
+
+from pathlib import Path
+
+import segno
+
+from kota_tech.core.logfile import read_log_file
+from kota_tech.matter.payload import SetupPayload, payload_from_log, verhoeff_check
+
+STICKER_QR = "MT:Y.K9042C00KA0648G00"
+STICKER_MANUAL = "34970112332"          # printed as 3497-011-2332
+
+
+def test_default_payload_matches_sticker():
+    p = SetupPayload()
+    assert p.qr_text() == STICKER_QR
+    assert p.manual_code() == STICKER_MANUAL
+    assert p.manual_code_pretty() == "3497-011-2332"
+
+
+def test_payload_from_real_boot_log():
+    lines = [ln.text for ln in read_log_file(Path(__file__).parent / "fixtures" / "serial_log_20260917_162548.txt")]
+    p = payload_from_log(lines)
+    assert p.from_log and (p.vendor_id, p.product_id, p.discriminator) == (0xFFF1, 0x8000, 3840)
+    assert p.qr_text() == STICKER_QR
+
+
+def test_other_discriminator_changes_both_codes():
+    p = SetupPayload(discriminator=1234)
+    assert p.qr_text() != STICKER_QR and p.manual_code() != STICKER_MANUAL
+    assert p.qr_text().startswith("MT:") and len(p.qr_text()) == 3 + 19
+
+
+def test_verhoeff():
+    assert verhoeff_check("3497011233") == 2
+    assert verhoeff_check("236") == 3          # textbook example
+
+
+def test_qr_renders():
+    qr = segno.make(STICKER_QR, error="m")
+    assert qr.symbol_size(border=0)[0] >= 21

tests/test_sd.py

@@ -0,0 +1,172 @@
+"""SD provisioning: ENV.TXT (firmware-exact parsing), disk discovery parsers,
+the elevated Windows format script, and write/check on a stand-in card."""
+
+import plistlib
+
+import pytest
+
+import sys
+from pathlib import Path
+
+from kota_tech.sd.disks import MAX_CARD_BYTES, Disk, Volume, parse_macos, parse_windows
+from kota_tech.sd.envfile import EnvConfig, parse_env
+from kota_tech.sd.provision import check_card, win_format_command, write_env
+
+URL = "https://influx.kota-app.com/api/v2/write?bucket=sensorbox&org=kota"
+TOKEN = "T" * 86 + "=="          # shape of an InfluxDB token, not a real one
+
+
+def cfg(**kw):
+    base = dict(influx_url=URL, influx_token=TOKEN)
+    base.update(kw)
+    return EnvConfig(**base)
+
+
+# ------------------------------------------------------------------ ENV.TXT
+
+def test_render_matches_the_factory_file_format():
+    raw = cfg().render()
+    assert raw == f"INFLUX_TOKEN={TOKEN}\nINFLUX_URL={URL}\n".encode()
+    assert not raw.startswith(b"\xef\xbb\xbf") and b"\r" not in raw
+    assert parse_env(raw).ok
+
+
+def test_wifi_only_written_when_both_set():
+    raw = cfg(ssid="Site WiFi", password="correct horse").render().decode()
+    assert "SSID=Site WiFi\n" in raw and "PASSWORD=correct horse\n" in raw
+    assert any("both SSID and PASSWORD" in i.text for i in cfg(ssid="x").problems())
+
+
+@pytest.mark.parametrize("kw,fragment", [
+    (dict(influx_url="influx.kota-app.com"), "https://"),
+    (dict(influx_url="https://influx.kota-app.com/"), "write URL"),
+    (dict(influx_token=""), "INFLUX_TOKEN is empty"),
+    (dict(influx_token="abc def" * 5), "spaces"),
+    (dict(influx_token=TOKEN + " "), "space"),
+    (dict(ssid="s" * 33, password="12345678"), "32 bytes"),
+    (dict(ssid="net", password="short"), "8-63"),
+])
+def test_invalid_settings_are_errors(kw, fragment):
+    errors = [i.text for i in cfg(**kw).problems() if i.level == "error"]
+    assert any(fragment in e for e in errors), errors
+
+
+def test_parser_mirrors_firmware():
+    raw = b"\xef\xbb\xbfINFLUX_TOKEN=abc\r\nINFLUX_URL = x\nINFLUX_URL=u1\nINFLUX_URL=u2\nHTTP_SERVER=true\n"
+    chk = parse_env(raw)
+    texts = " ".join(i.text for i in chk.issues)
+    assert "BOM" in texts                                   # first key unreadable
+    assert "spaces around the key 'INFLUX_URL'" in texts
+    assert chk.values["INFLUX_URL"] == "u1"                 # first match wins
+    assert "appears twice" in texts and "setup mode" in texts
+    assert "INFLUX_TOKEN is missing" in texts               # hidden behind the BOM
+    assert not chk.ok
+
+
+def test_masking():
+    chk = parse_env(cfg(ssid="net", password="secretpassword").render())
+    m = chk.masked()
+    assert TOKEN not in m["INFLUX_TOKEN"] and m["INFLUX_TOKEN"].startswith("TTTT")
+    assert "secret" not in m["PASSWORD"]
+
+
+# ------------------------------------------------------------- disk lists
+
+WIN_JSON = """[{"Number":0,"FriendlyName":"ST500DM002-1BC142","Size":500107862016,"BusType":"SATA",
+ "Volumes":[{"DriveLetter":"D","FileSystem":"NTFS","Label":"WINRE"}]},
+ {"Number":4,"FriendlyName":"Mass Storage Device","Size":0,"BusType":"USB","Volumes":[]},
+ {"Number":5,"FriendlyName":"SDXC Card","Size":31914983424,"BusType":"SD",
+  "Volumes":{"DriveLetter":"E","FileSystem":"FAT32","Label":"KOTA"}}]"""
+
+
+def test_parse_windows_keeps_only_card_buses():
+    disks = parse_windows(WIN_JSON)
+    assert [d.id for d in disks] == ["4", "5"]              # SATA data disk never listed
+    reader, card = disks
+    assert not reader.has_media and reader.size_text == "no card"
+    assert card.volumes[0].mount == "E:\\" and card.volumes[0].filesystem == "FAT32"
+
+
+def test_parse_windows_single_object_quirk():
+    one = '{"Number":5,"FriendlyName":"SD","Size":8000000000,"BusType":"USB","Volumes":null}'
+    assert [d.id for d in parse_windows(one)] == ["5"]
+
+
+def test_parse_macos_excludes_system_disk():
+    listing = plistlib.dumps({"AllDisksAndPartitions": [
+        {"DeviceIdentifier": "disk0", "Size": 500_000_000_000, "Partitions": []},
+        {"DeviceIdentifier": "disk3", "Size": 994_000_000_000, "Partitions": [], "APFSVolumes": [{"MountPoint": "/"}]},
+        {"DeviceIdentifier": "disk4", "Size": 15_931_539_456,
+         "Partitions": [{"DeviceIdentifier": "disk4s1", "MountPoint": "/Volumes/KOTA", "Content": "DOS_FAT_32",
+                         "VolumeName": "KOTA"}]},
+    ]})
+    infos = {"disk0": plistlib.dumps({"Internal": True, "BusProtocol": "PCI-Express"}),
+             "disk3": plistlib.dumps({"Internal": True}),
+             "disk4": plistlib.dumps({"Internal": True, "RemovableMedia": True, "BusProtocol": "Secure Digital",
+                                      "MediaName": "SD Card Reader"})}
+    disks = parse_macos(listing, infos)
+    assert [d.id for d in disks] == ["/dev/disk4"] and disks[0].bus == "SD"
+    assert disks[0].volumes[0].mount == "/Volumes/KOTA"
+
+
+# -------------------------------------------------------- format script
+
+def test_elevated_helper_command(tmp_path):
+    disk = Disk("5", "SDXC Card", 63_864_569_856, "SD")
+    prog, params, cwd = win_format_command(disk, tmp_path / "r.json")
+    assert params.startswith("-m kota_tech.sd.win_format --disk 5 --size 63864569856 --label KOTA")
+    assert (Path(cwd) / "kota_tech").is_dir()                 # helper is importable from there
+
+
+@pytest.mark.skipif(sys.platform != "win32", reason="Windows formatter")
+@pytest.mark.parametrize("disks,msg", [
+    ([], "not a USB/SD/MMC"),                                                     # disk vanished / internal
+    ([Disk("5", "SD", 1_000, "SD")], "changed since it was selected"),              # swapped card
+    ([Disk("5", "SD", 31_457_280_000, "SD", [Volume("C:\\", "NTFS", "")])], "Windows drive"),
+])
+def test_formatter_guard_refuses_before_writing(monkeypatch, disks, msg):
+    from kota_tech.sd import win_format
+    monkeypatch.setattr(win_format.win_disks, "list_disks", lambda buses: disks)
+    monkeypatch.setattr(win_format, "RawDisk", lambda *a: pytest.fail("must not open the disk for writing"))
+    with pytest.raises(win_format.FormatError, match=msg):
+        win_format.format_card(5, 31_457_280_000, "KOTA", {})
+
+
+def test_large_disks_are_not_cards():
+    assert MAX_CARD_BYTES == 256 * 1024**3
+
+
+# ----------------------------------------------- write / check on a card
+
+def test_write_env_replaces_variants_and_keeps_buffered_data(tmp_path):
+    card = tmp_path / "card"
+    card.mkdir()
+    (card / "env.txt").write_bytes(b"INFLUX_URL=old\n")
+    (card / "BUFFER.TXT").write_bytes(b"line1\nline2\n\n")
+    out = write_env(str(card), cfg())
+    assert out.ok, out.message
+    names = sorted(p.name for p in card.iterdir())
+    assert names == ["BUFFER.TXT", "ENV.TXT"]
+    rep = check_card(str(card), "FAT32")
+    assert rep.env.ok and rep.problems == [] and rep.buffered_lines == 2
+
+
+def test_write_env_refuses_invalid_settings(tmp_path):
+    assert not write_env(str(tmp_path), cfg(influx_token="")).ok
+    assert not (tmp_path / "ENV.TXT").exists()
+
+
+def test_check_card_reports_missing_env_and_wrong_fs(tmp_path):
+    rep = check_card(str(tmp_path), "exFAT")
+    texts = " ".join(rep.problems)
+    assert "needs FAT32" in texts and "No ENV.TXT" in texts
+
+
+def test_elevated_result_folder_is_not_owner_only(tmp_path, monkeypatch):
+    # Regression: tempfile.mkdtemp() made the elevated script's result unreadable.
+    import kota_tech.sd.provision as prov
+    monkeypatch.setattr(prov, "WORK_ROOT", tmp_path / "tmp")
+    work = prov._workdir()
+    assert work.parent == tmp_path / "tmp" and work.is_dir()
+    (work / "result.json").write_text('{"ok": true}', encoding="utf-8")
+    assert (work / "result.json").read_text(encoding="utf-8")

tests/test_service.py

@@ -0,0 +1,91 @@
+"""Service-system hand-off: status mapping, note, and the #kota-report fragment
+(decoded exactly as the v1.1.0 service page does: base64url + UTF-8 JSON)."""
+
+import base64
+import json
+from pathlib import Path
+
+import pytest
+
+from kota_tech.core.logfile import read_log_file
+from kota_tech.core.logline import parse_line
+from kota_tech.diag.engine import DiagnosticsEngine
+from kota_tech.service.report import (
+    CONNECTIVITY, HARDWARE, OK, decode_fragment, normalize_mac, report_url, service_note, service_status,
+)
+
+FIX = Path(__file__).parent / "fixtures"
+
+
+def bench():
+    e = DiagnosticsEngine()
+    for ln in read_log_file(FIX / "live_boot_A4CB8FC946F8_fw1.0.txt"):
+        e.feed(ln)
+    return e
+
+
+def test_engine_reads_mac_from_boot_log():
+    assert bench().mac == "A4:CB:8F:C9:46:F8"
+
+
+def test_bench_box_is_a_connectivity_problem():
+    e = bench()
+    assert service_status(e.report()) == CONNECTIVITY
+    note = service_note(e.report())
+    assert note.startswith("[KOTA Technician Tool")
+    assert "not commissioned in Matter" in note and "-> No Internet" in note
+    assert "Firmware: v1.0" in note
+
+
+def test_hardware_and_healthy_statuses():
+    e = DiagnosticsEngine()
+    for ln in ["ESP-ROM:esp32s3-20210327", "I (1299) app_init: Project name:     kota-sensorboard",
+               "E (3511) MAIN: Failed to initialize RTC: ESP_ERR_TIMEOUT"]:
+        e.feed(parse_line(ln))
+    assert service_status(e.report()) == HARDWARE
+    ok = DiagnosticsEngine()
+    for ln in ["ESP-ROM:esp32s3-20210327", "I (1299) app_init: Project name:     kota-sensorboard",
+               "I (31000) INFLUX: HTTP request performed, status code: 204"]:
+        ok.feed(parse_line(ln))
+    assert service_status(ok.report()) == OK
+
+
+def test_url_shape_and_payload_roundtrip():
+    e = bench()
+    url = report_url(e.mac, e.report(), "https://service.kota-app.com")
+    assert url.startswith("https://service.kota-app.com/A4CB8FC946F8#kota-report=")
+    assert "?" not in url                       # nothing in the query: the fragment is never sent to a server
+    data = decode_fragment(url)
+    assert data["v"] == 1 and data["mac"] == "A4CB8FC946F8" and data["status"] == CONNECTIVITY
+
+
+def test_fragment_decodes_like_the_service_page():
+    # Mirror of index.html applyToolPrefill: base64url -> pad -> bytes -> UTF-8 -> JSON
+    e = bench()
+    e.note_technician("Zażółć gęślą jaźń -> Purple")        # non-ASCII survives
+    url = report_url("a4:cb:8f:c9:46:f8", e.report())
+    frag = url.split("#kota-report=")[1]
+    assert set(frag) <= set("ABCDEFGHIJKLMNOPQRSTUVWXYZabcdefghijklmnopqrstuvwxyz0123456789-_")   # page regex
+    padded = frag.replace("-", "+").replace("_", "/")
+    padded += "==="[(len(padded) + 3) % 4:]
+    data = json.loads(base64.b64decode(padded).decode("utf-8"))
+    assert "Zażółć gęślą jaźń" in data["note"]
+
+
+def test_note_is_limited_and_no_secrets():
+    e = bench()
+    for i in range(400):
+        e.note_technician(f"check {i} " + "x" * 50)
+    note = service_note(e.report(), limit=4000)
+    assert len(note) <= 4000
+    assert "INFLUX_TOKEN" not in note
+
+
+@pytest.mark.parametrize("bad", ["", "A4CB8F", "zz:cb:8f:c9:46:f8"])
+def test_invalid_mac_rejected(bad):
+    with pytest.raises(ValueError):
+        report_url(bad, bench().report())
+
+
+def test_normalize_mac():
+    assert normalize_mac("a4:cb:8f:c9:46:f8") == "A4CB8FC946F8"

uv.lock

@@ -1,6 +1,138 @@
 version = 1
 revision = 3
 requires-python = ">=3.11, <3.14"
+resolution-markers = [
+    "platform_machine == 'x86_64' and sys_platform == 'darwin'",
+    "platform_machine != 'x86_64' or sys_platform != 'darwin'",
+]
+
+[[package]]
+name = "appdirs"
+version = "1.4.4"
+source = { registry = "https://pypi.org/simple" }
+sdist = { url = "https://files.pythonhosted.org/packages/d7/d8/05696357e0311f5b5c316d7b95f46c669dd9c15aaeecbb48c7d0aeb88c40/appdirs-1.4.4.tar.gz", hash = "sha256:7d5d0167b2b1ba821647616af46a749d1c653740dd0d2415100fe26e27afdf41", size = 13470, upload-time = "2020-05-11T07:59:51.037Z" }
+wheels = [
+    { url = "https://files.pythonhosted.org/packages/3b/00/2344469e2084fb287c2e0b57b72910309874c3245463acd6cf5e3db69324/appdirs-1.4.4-py2.py3-none-any.whl", hash = "sha256:a841dacd6b99318a741b166adb07e19ee71a274450e68237b4650ca1055ab128", size = 9566, upload-time = "2020-05-11T07:59:49.499Z" },
+]
+
+[[package]]
+name = "argcomplete"
+version = "3.7.2"
+source = { registry = "https://pypi.org/simple" }
+sdist = { url = "https://files.pythonhosted.org/packages/87/6f/5a73f04007ca950701765949209f068da628bd11f9c2da287278ce91e0ee/argcomplete-3.7.2.tar.gz", hash = "sha256:aad8b69a0b9969edb62db0d1752354c0d50717b10e0cbb00e2a958381b9fc6b9", size = 74473, upload-time = "2026-08-06T04:53:21.662Z" }
+wheels = [
+    { url = "https://files.pythonhosted.org/packages/46/bd/551ee6af426af84ca33e02622be722925c196608e9127d731ef17c47f06e/argcomplete-3.7.2-py3-none-any.whl", hash = "sha256:6029205678bdd9c1c728a155f5f9ecf5812393f969eef58807641a2bc2aa5b19", size = 43294, upload-time = "2026-08-06T04:53:20.246Z" },
+]
+
+[[package]]
+name = "bitarray"
+version = "3.11.0"
+source = { registry = "https://pypi.org/simple" }
+sdist = { url = "https://files.pythonhosted.org/packages/04/f7/6765577df59e2345036e435f7e983e1c291d67b7d76a51918eff04ad1494/bitarray-3.11.0.tar.gz", hash = "sha256:bf19437ec00ec3d40aef82eaeedc14cf4000be9b635c4f5049796506e6630dd8", size = 174911, upload-time = "2026-09-01T15:21:52.076Z" }
+wheels = [
+    { url = "https://files.pythonhosted.org/packages/86/55/aeb2eb3870a31257a29d3830f7d5804253d2070727ef6475629455491d33/bitarray-3.11.0-cp311-cp311-macosx_10_9_x86_64.whl", hash = "sha256:470940879d8553fecddc3cf306b7d4b69fa0f5b7a6e3790b238fe553578061c1", size = 170436, upload-time = "2026-09-01T15:19:54.02Z" },
+    { url = "https://files.pythonhosted.org/packages/fb/b4/38b6131ecd500f8f853367339b9e95ad4644d47729bcbf0fa2c5e4c06a91/bitarray-3.11.0-cp311-cp311-macosx_11_0_arm64.whl", hash = "sha256:56a2aa49e900aa927c147328e571da8a38a50ae99277ed093290845498dedefc", size = 166780, upload-time = "2026-09-01T15:19:55.173Z" },
+    { url = "https://files.pythonhosted.org/packages/eb/28/d1e0493106911b08d3d328e463aa140ca76fcab6cdcda06912ffb59d53cf/bitarray-3.11.0-cp311-cp311-manylinux2014_aarch64.manylinux_2_17_aarch64.manylinux_2_28_aarch64.whl", hash = "sha256:55370f00c52b5e46800fee0218a27a1b99db6e09113c1b804190c039e4350ea1", size = 380740, upload-time = "2026-09-01T15:19:56.253Z" },
+    { url = "https://files.pythonhosted.org/packages/90/85/1ebb39e36b7102358942609583aa5a027b7e1eb83e140ad3fba86e53adba/bitarray-3.11.0-cp311-cp311-manylinux2014_ppc64le.manylinux_2_17_ppc64le.manylinux_2_28_ppc64le.whl", hash = "sha256:155205159f3c38180a705253341b8200414c0198e86a9b9e2db49010236ff785", size = 404566, upload-time = "2026-09-01T15:19:57.474Z" },
+    { url = "https://files.pythonhosted.org/packages/24/8d/e94bfa36a7cadcd16415afe531e0a01c6e2dc2bb11095c6c52fca384c642/bitarray-3.11.0-cp311-cp311-manylinux2014_s390x.manylinux_2_17_s390x.manylinux_2_28_s390x.whl", hash = "sha256:1c49fc5f57eea2e859a3f2936a1fed84510af6f7464572b641485de2d22148cb", size = 418899, upload-time = "2026-09-01T15:19:58.547Z" },
+    { url = "https://files.pythonhosted.org/packages/2a/3a/859196ab78c6fa0aa8f04155308dd314265c8c27e09350bcd3894fc333d8/bitarray-3.11.0-cp311-cp311-manylinux2014_x86_64.manylinux_2_17_x86_64.manylinux_2_28_x86_64.whl", hash = "sha256:41545b21384fd91767d294a5b3526c6306f7db577cf59ba72b51498e90bd52a7", size = 383414, upload-time = "2026-09-01T15:19:59.649Z" },
+    { url = "https://files.pythonhosted.org/packages/75/fc/5fafae3bee337c31372293fcc6259960e9bcaf89825f07798514213c5686/bitarray-3.11.0-cp311-cp311-musllinux_1_2_aarch64.whl", hash = "sha256:afe8ee837c085eeeaead62429f260a2de3a0602d1a34bcdead8b9f0388ef6114", size = 378658, upload-time = "2026-09-01T15:20:00.751Z" },
+    { url = "https://files.pythonhosted.org/packages/23/c8/39a1e59453b99a67ee449d9d0c378f5e282ec4c00645127a9aaa4a5adba7/bitarray-3.11.0-cp311-cp311-musllinux_1_2_ppc64le.whl", hash = "sha256:4bddbc76e619a36d2abad14713c4dd970a8fa46a75a85ebbb626a2f26f1821d8", size = 401990, upload-time = "2026-09-01T15:20:01.951Z" },
+    { url = "https://files.pythonhosted.org/packages/87/aa/add67250e559e24fdc585921062e388395e0b47f40c6aa13e1ee493a13d4/bitarray-3.11.0-cp311-cp311-musllinux_1_2_s390x.whl", hash = "sha256:027766e71da6063cb51fcd4c51f031ac14d5088ecb55e4500ffd692d78630dd3", size = 399837, upload-time = "2026-09-01T15:20:03.202Z" },
+    { url = "https://files.pythonhosted.org/packages/6e/80/c758fa566da3180e43fba1a9bc2c84b29fc5e25ce0149155378e89ee4172/bitarray-3.11.0-cp311-cp311-musllinux_1_2_x86_64.whl", hash = "sha256:116a23f655f394f80f41fdc03368862485ac05534a56991eefb9f18f72e17f17", size = 380673, upload-time = "2026-09-01T15:20:04.461Z" },
+    { url = "https://files.pythonhosted.org/packages/b2/8a/fcb7bef53c2aacdbc2ca07f498e5249ab7d87dbfed666f184bb8d16fec0f/bitarray-3.11.0-cp311-cp311-win32.whl", hash = "sha256:30597fa6f4116eb6e374568d4f4de7e220462368ec7ce37d93403871bdf27a8c", size = 160605, upload-time = "2026-09-01T15:20:05.525Z" },
+    { url = "https://files.pythonhosted.org/packages/9f/2c/3d3f3f7846432bc1f630c99fa5cd595674b5318c77c774b6c028bdbf05ad/bitarray-3.11.0-cp311-cp311-win_amd64.whl", hash = "sha256:7b16df7ddef03e30622d894cce86a560b7888415ddcac470eb99940a5adf1a35", size = 171179, upload-time = "2026-09-01T15:20:06.579Z" },
+    { url = "https://files.pythonhosted.org/packages/54/20/c8cb10050d1afed77e0511861ba49d56724fd846b4a0b596f52e7ebe5711/bitarray-3.11.0-cp311-cp311-win_arm64.whl", hash = "sha256:ec3d8b99a92220bdba382acf4eff370d6a6cda34a5ce936726cb9e8cf2427c47", size = 166363, upload-time = "2026-09-01T15:20:07.626Z" },
+    { url = "https://files.pythonhosted.org/packages/26/74/c878e209fd15fdf0460763199892fc4e74c6a7345f5161ad673af586f2fe/bitarray-3.11.0-cp312-cp312-macosx_10_13_x86_64.whl", hash = "sha256:93a7f9f9f848ec79f19fdd39f3b8f750d9abf8e65cd6fb3a045df192de23855d", size = 170727, upload-time = "2026-09-01T15:20:08.703Z" },
+    { url = "https://files.pythonhosted.org/packages/ce/f8/4463653a8c909796c8f8931d0fd64344c6745a144e432d0310435197b0ed/bitarray-3.11.0-cp312-cp312-macosx_11_0_arm64.whl", hash = "sha256:3889cf12ae0c04076772c8be66655bfe5925003b44dec056b569a68a121f7e93", size = 166746, upload-time = "2026-09-01T15:20:09.719Z" },
+    { url = "https://files.pythonhosted.org/packages/03/30/edaec4a0fffd04ee98b1425a597dc1d350c4def690b0a34815a75e5c2c33/bitarray-3.11.0-cp312-cp312-manylinux2014_aarch64.manylinux_2_17_aarch64.manylinux_2_28_aarch64.whl", hash = "sha256:823638d0a900cea53c173fb31f5f1f4b913065a92fa3406d9b20eb7b7ebf189d", size = 383620, upload-time = "2026-09-01T15:20:10.78Z" },
+    { url = "https://files.pythonhosted.org/packages/83/1d/8fba2e884d5e5e7fa6828b4ca461e819259bac0f6f99073388157ea1c6d6/bitarray-3.11.0-cp312-cp312-manylinux2014_ppc64le.manylinux_2_17_ppc64le.manylinux_2_28_ppc64le.whl", hash = "sha256:301763ffde9d288c5a58dda51c5290bc1081c2bc0faf266c4aef227ca59004d5", size = 406908, upload-time = "2026-09-01T15:20:12.061Z" },
+    { url = "https://files.pythonhosted.org/packages/8d/71/414853d582267d8e397ea5bf894503236d81660c5d7a34b2a0d0ec6e9f2d/bitarray-3.11.0-cp312-cp312-manylinux2014_s390x.manylinux_2_17_s390x.manylinux_2_28_s390x.whl", hash = "sha256:664f02e6e2c63fcc1c02718d2daa21b04f77a18ef3850a9b348597c0c8a0f222", size = 422031, upload-time = "2026-09-01T15:20:13.157Z" },
+    { url = "https://files.pythonhosted.org/packages/9a/1c/35b3f34fee6f91f708eb81af03438afc137b2e5fc0e27ec11d948287f64c/bitarray-3.11.0-cp312-cp312-manylinux2014_x86_64.manylinux_2_17_x86_64.manylinux_2_28_x86_64.whl", hash = "sha256:52741a1d24a3723a8151259906cf1befeaf3d4ccf7d3e27e8be4334590b59bcd", size = 387692, upload-time = "2026-09-01T15:20:14.377Z" },
+    { url = "https://files.pythonhosted.org/packages/7a/a9/7ebe3e04548cee84fba250425935a500ff02e7fef1b020ed182a3f5227c4/bitarray-3.11.0-cp312-cp312-musllinux_1_2_aarch64.whl", hash = "sha256:3a1093eb1a756f08c7bdeb22969fb463aa62f036dc191ad371af5e292108c611", size = 381169, upload-time = "2026-09-01T15:20:15.515Z" },
+    { url = "https://files.pythonhosted.org/packages/fe/48/cdf80b633f326451de801504f8718dd71ce63f534d29348822896d9c5bd2/bitarray-3.11.0-cp312-cp312-musllinux_1_2_ppc64le.whl", hash = "sha256:ab0988829e4ed10fa971842e9fbf77595b8a4557a078a3589b0754f06417ddff", size = 404500, upload-time = "2026-09-01T15:20:16.804Z" },
+    { url = "https://files.pythonhosted.org/packages/54/cf/a64cab1bb0f48101ac45fb45a7f0d000af76e26ed0ab26b52573140a9a64/bitarray-3.11.0-cp312-cp312-musllinux_1_2_s390x.whl", hash = "sha256:c4cabc2439ab3ce76881037741bf41e9fafda217ff721fdee92701e5fe3c8b9c", size = 402903, upload-time = "2026-09-01T15:20:18.127Z" },
+    { url = "https://files.pythonhosted.org/packages/79/b8/c3937572587a0503ea0a05ae61543916d6d93ffe48c26532cad9c4bfd9e4/bitarray-3.11.0-cp312-cp312-musllinux_1_2_x86_64.whl", hash = "sha256:9db61968efb834dacda6bcd7ef1f8a033253a53ac31426a684a28a7e4c9f2f29", size = 384582, upload-time = "2026-09-01T15:20:19.481Z" },
+    { url = "https://files.pythonhosted.org/packages/29/13/824648ef8f3fc14f56c4f9903e6c06979385f0c3a4d76371f6ccd8e9d1b2/bitarray-3.11.0-cp312-cp312-win32.whl", hash = "sha256:97cd5913000e4e56d211f7db053284d1f753aed34838368769bf084474a76f0a", size = 160902, upload-time = "2026-09-01T15:20:21.037Z" },
+    { url = "https://files.pythonhosted.org/packages/f1/c4/0a1608187e6d21b30c341ebcce6f75efbc8fe289f87ad58aa4149ce59828/bitarray-3.11.0-cp312-cp312-win_amd64.whl", hash = "sha256:5db38c0a36d07190c3629c65dab2504233a56b1c35d8b1cc3d7369943d028711", size = 171542, upload-time = "2026-09-01T15:20:22.114Z" },
+    { url = "https://files.pythonhosted.org/packages/a8/59/f21b457eb6ab683ccf755093550ec1408e8ec8a66b980653c99740b85552/bitarray-3.11.0-cp312-cp312-win_arm64.whl", hash = "sha256:9aafe7dc6d568470f5c297d0b15acddd3afc1677c983f0460b28f8cac4e9360c", size = 166561, upload-time = "2026-09-01T15:20:23.177Z" },
+    { url = "https://files.pythonhosted.org/packages/2d/3d/578c4b63b3c1f206dfe7f7f60e941ca2d0aafd9da43943c076c01e976ec0/bitarray-3.11.0-cp313-cp313-macosx_10_13_x86_64.whl", hash = "sha256:ac322a81c3c938c13093d8d77c419093f50118c29fbfa9eb80813d93af1a2d95", size = 170422, upload-time = "2026-09-01T15:20:24.673Z" },
+    { url = "https://files.pythonhosted.org/packages/9a/30/3f982be25cf0c858351490b6d0cf6168e8668bb81e3daac25d8a3b2b8e44/bitarray-3.11.0-cp313-cp313-macosx_11_0_arm64.whl", hash = "sha256:ece8caff2fb31d6c69430d3dfc0efff70083e66b012f7f5de60cfe5dca98ba87", size = 166475, upload-time = "2026-09-01T15:20:25.649Z" },
+    { url = "https://files.pythonhosted.org/packages/78/ad/f94c267873f0c80705dcef602af0a8d3f42838197e8fff01033f2a8084c9/bitarray-3.11.0-cp313-cp313-manylinux2014_aarch64.manylinux_2_17_aarch64.manylinux_2_28_aarch64.whl", hash = "sha256:962dc3e5622a08bb1c1ad429a9f7dace7efadd7fef1fcdf1628a6db142333256", size = 381856, upload-time = "2026-09-01T15:20:26.799Z" },
+    { url = "https://files.pythonhosted.org/packages/0d/ce/e9ba5d080302c4d6fa269bccc7ad6ed4a5ad36a1dc75baae334714bbc183/bitarray-3.11.0-cp313-cp313-manylinux2014_ppc64le.manylinux_2_17_ppc64le.manylinux_2_28_ppc64le.whl", hash = "sha256:de25b8c76fe9fe7d9c6bce2832096f020133e1d21e2841abd7280937bf90e56e", size = 405246, upload-time = "2026-09-01T15:20:27.888Z" },
+    { url = "https://files.pythonhosted.org/packages/56/4c/cce77df63010304704eb802d884d9b11c84f63a02d7c4081a41225e25343/bitarray-3.11.0-cp313-cp313-manylinux2014_s390x.manylinux_2_17_s390x.manylinux_2_28_s390x.whl", hash = "sha256:86dfaab663a2ad16ed2f6252116cf034cfc84282aa744f19a9a66542e85c9ca9", size = 420083, upload-time = "2026-09-01T15:20:29.213Z" },
+    { url = "https://files.pythonhosted.org/packages/8f/1f/2c7b1a995af9814b6ec5ee69333a0a6131924ed0f3f10ffbd73c22c0a6ad/bitarray-3.11.0-cp313-cp313-manylinux2014_x86_64.manylinux_2_17_x86_64.manylinux_2_28_x86_64.whl", hash = "sha256:5605c8e74f95f77dd1b93c8c83d6fefe0d41d2704683d4a72152ca5284e2546d", size = 385572, upload-time = "2026-09-01T15:20:30.604Z" },
+    { url = "https://files.pythonhosted.org/packages/36/58/53845d1ddbe6077b61e7f39f586f7f35f18ce7dc47f178331e4fd64f59e1/bitarray-3.11.0-cp313-cp313-musllinux_1_2_aarch64.whl", hash = "sha256:d62e73fcdd273d07b1e9699de0e66e4d367b28c554c86bfe7c92029337c2a414", size = 379323, upload-time = "2026-09-01T15:20:31.69Z" },
+    { url = "https://files.pythonhosted.org/packages/06/66/b67544886466ede3d26e58c43d9841cc427d4fdcd81ded4087313687241a/bitarray-3.11.0-cp313-cp313-musllinux_1_2_ppc64le.whl", hash = "sha256:9808734d1e5fd2839660a9db1abfe93e9d64b2aa9ed59aa480193ad93e8d620e", size = 402087, upload-time = "2026-09-01T15:20:33.113Z" },
+    { url = "https://files.pythonhosted.org/packages/93/a7/4ffc5984f3f4a12458adbceff60def49752f74807945771428f97694aec0/bitarray-3.11.0-cp313-cp313-musllinux_1_2_s390x.whl", hash = "sha256:8b77aa18131418b869be882df1c5e229fb02f90861783bbe638d9ebe296e9209", size = 401000, upload-time = "2026-09-01T15:20:34.658Z" },
+    { url = "https://files.pythonhosted.org/packages/e8/15/2d5dd4107e49b2c0040bc9cc48ee5af7f45772fedae3bc54fa987aeeedf2/bitarray-3.11.0-cp313-cp313-musllinux_1_2_x86_64.whl", hash = "sha256:d084fa59c94d3fec7eac6793e08162fa697aa4e70b9f519618c29d3e54eda752", size = 382431, upload-time = "2026-09-01T15:20:36.013Z" },
+    { url = "https://files.pythonhosted.org/packages/4d/8b/8d95483688bcf297654c87b65ef1847fad794adb083d294da65ac275d4fc/bitarray-3.11.0-cp313-cp313-win32.whl", hash = "sha256:387b64dc54be3732a0988bf3731fc06d7d4f52dc9470d1a5479e8ce2b67d368b", size = 160760, upload-time = "2026-09-01T15:20:37.241Z" },
+    { url = "https://files.pythonhosted.org/packages/d2/9b/b10ebf5e9a479815d2d54908617c0c55b255965389d3132927c9cd9ccf86/bitarray-3.11.0-cp313-cp313-win_amd64.whl", hash = "sha256:b4afbb464a1db2d37858bd3b87bd59a76b4aae5e29ec007a9fd00bf5a911e1da", size = 171278, upload-time = "2026-09-01T15:20:38.646Z" },
+    { url = "https://files.pythonhosted.org/packages/16/3a/b0a29fc2379c567eb49730022c5913ad85b2f9ccda1b841737f756e1fb87/bitarray-3.11.0-cp313-cp313-win_arm64.whl", hash = "sha256:36da946f64e10e28b23f345fde90f4d14e9c2e9013364fe04d9b2013e7291285", size = 166426, upload-time = "2026-09-01T15:20:39.862Z" },
+]
+
+[[package]]
+name = "bitstring"
+version = "4.4.0"
+source = { registry = "https://pypi.org/simple" }
+dependencies = [
+    { name = "bitarray" },
+    { name = "tibs" },
+]
+sdist = { url = "https://files.pythonhosted.org/packages/36/d3/de6fe4e7065df8c2f1ac1766f5fdccbe75bc18af2cf2dbeecd34d68e1518/bitstring-4.4.0.tar.gz", hash = "sha256:e682ac522bb63e041d16cbc9d0ca86a4f00194db16d0847c7efe066f836b2e37", size = 255209, upload-time = "2026-03-10T20:29:14.824Z" }
+wheels = [
+    { url = "https://files.pythonhosted.org/packages/bf/02/1a870bab76f2896d827aa4963be95e56675ffa1453e53525d13c43036edf/bitstring-4.4.0-py3-none-any.whl", hash = "sha256:feac49524fcf3ef27e6081e86f02b10d2adf6c3773bf22fbe0e7eea9534bc737", size = 76846, upload-time = "2026-03-10T20:29:12.832Z" },
+]
+
+[[package]]
+name = "cffi"
+version = "2.1.1"
+source = { registry = "https://pypi.org/simple" }
+dependencies = [
+    { name = "pycparser", marker = "implementation_name != 'PyPy'" },
+]
+sdist = { url = "https://files.pythonhosted.org/packages/9e/ef/008a1939e372c06329a3fce4279c02f328488f3526744906eeec3da7ad5f/cffi-2.1.1.tar.gz", hash = "sha256:dd31f52ea1086513bb9df30f8fcee9b8918323ae067a3d5b78bc826a000712be", size = 530807, upload-time = "2026-08-03T21:21:18.939Z" }
+wheels = [
+    { url = "https://files.pythonhosted.org/packages/70/d2/16d99a0c4948febc0ebd133a13b2f688ff7f8cb04da971e1128872ce0c03/cffi-2.1.1-cp311-cp311-macosx_10_15_x86_64.whl", hash = "sha256:c8d2c9fd1f2d16f780d15127abb050d13d1a76c03a4bd87d7e4980e45e511e12", size = 183838, upload-time = "2026-08-03T21:19:29.637Z" },
+    { url = "https://files.pythonhosted.org/packages/cd/95/31b535a9f0220ae9f357de4a08d57ce89cb417653c2fd9f075f50822a388/cffi-2.1.1-cp311-cp311-macosx_11_0_arm64.whl", hash = "sha256:398aff33cee2767e3e781d2554c54bd0dff386bb437581e0d8011fde1a942ec1", size = 184168, upload-time = "2026-08-03T21:19:30.764Z" },
+    { url = "https://files.pythonhosted.org/packages/ad/5a/4707a0dc1f203f5dde5a907b0d4e3c25d71120241048bd5bc6f1bb9d4e71/cffi-2.1.1-cp311-cp311-manylinux1_i686.manylinux2014_i686.manylinux_2_17_i686.manylinux_2_5_i686.whl", hash = "sha256:154852545011f779917b11c78db2358d095da62a9a172b78ad0a583ee5adc0d0", size = 211805, upload-time = "2026-08-03T21:19:31.867Z" },
+    { url = "https://files.pythonhosted.org/packages/ad/66/c19feabb28485b6e0bbaaafa90837a1ef5d302e90f2178bd33f17a49879b/cffi-2.1.1-cp311-cp311-manylinux2014_aarch64.manylinux_2_17_aarch64.whl", hash = "sha256:3311ed60d36f83378794e1009ac6258bafbf81f7888b4caa7b35a521e3f95813", size = 218716, upload-time = "2026-08-03T21:19:32.896Z" },
+    { url = "https://files.pythonhosted.org/packages/a7/92/500760486c8baab49a7a8a58ba7fc3355ec3974b454b8a09e528efde9e1d/cffi-2.1.1-cp311-cp311-manylinux2014_ppc64le.manylinux_2_17_ppc64le.whl", hash = "sha256:6e192623c49c94421616a5778fba35cf0d5a8d000650c1967ef4448ee5cdd990", size = 205569, upload-time = "2026-08-03T21:19:34.142Z" },
+    { url = "https://files.pythonhosted.org/packages/a5/a7/a67c733254d6e7373f7822f8082d8d6beade791e0cf12a7611f376fa61c7/cffi-2.1.1-cp311-cp311-manylinux2014_s390x.manylinux_2_17_s390x.whl", hash = "sha256:a6e721d4b0e45d5b65e87534470e67b18dcd092c83f68fba09f152b9cbc061af", size = 204907, upload-time = "2026-08-03T21:19:35.174Z" },
+    { url = "https://files.pythonhosted.org/packages/f7/a4/4399daaf8f7dfee9d7c3327fdb0426ee041cc63edc358b93911ceb2bfc7a/cffi-2.1.1-cp311-cp311-manylinux2014_x86_64.manylinux_2_17_x86_64.whl", hash = "sha256:34e261f78cb6ceaaa36f42f2613f4380d94d9c759a9c73c769ee6e0247364632", size = 217807, upload-time = "2026-08-03T21:19:36.286Z" },
+    { url = "https://files.pythonhosted.org/packages/28/f7/dabe6da2466ecbd82dc62e7342dc6b1065dad990c06f00f0ede9ebf2a0ed/cffi-2.1.1-cp311-cp311-musllinux_1_2_aarch64.whl", hash = "sha256:7225e4514edb64eb6740324353e0da0711954fd8d7da4576755b1c6e09b697cd", size = 221252, upload-time = "2026-08-03T21:19:37.416Z" },
+    { url = "https://files.pythonhosted.org/packages/ce/87/616202d8e51342c07d2534c510111c4cc37201775ce8f60802c9335d1edd/cffi-2.1.1-cp311-cp311-musllinux_1_2_i686.whl", hash = "sha256:df913725b79db7bcf03448f36b7bf8815363417d5b58deecf9305e3e30f0f21a", size = 214214, upload-time = "2026-08-03T21:19:38.507Z" },
+    { url = "https://files.pythonhosted.org/packages/b4/c6/ab025d75d2c26c19b087c0124e75ee31cb65032f4fe345d356d8c507ab97/cffi-2.1.1-cp311-cp311-musllinux_1_2_x86_64.whl", hash = "sha256:f5cfbc5fe74540d335175b656c725d74d90e3730c626d92575eea35029d9afaa", size = 219408, upload-time = "2026-08-03T21:19:39.809Z" },
+    { url = "https://files.pythonhosted.org/packages/db/e2/7e8109f65445bdc673a7b54f02c677de462db75674220fd1335efc8eb598/cffi-2.1.1-cp311-cp311-win32.whl", hash = "sha256:f8ec5e643a9a937f64e1999eb9f75d072263751912dc5cd06d3c85f8f44be7c3", size = 174470, upload-time = "2026-08-03T21:19:41.246Z" },
+    { url = "https://files.pythonhosted.org/packages/73/c0/77ba02423c2f7d7091143c45cd49e0e6575c4c1967394bb542bd923a9b74/cffi-2.1.1-cp311-cp311-win_amd64.whl", hash = "sha256:42f6930c31dc7f50732c9ae793c2786c7b6b044195967bbdde40bb9be81c4cc0", size = 185096, upload-time = "2026-08-03T21:19:42.615Z" },
+    { url = "https://files.pythonhosted.org/packages/7c/47/9f1f85f9672ceda4984dc6c4f8824e8558992a2972c3d3c81fb8eb28d4ba/cffi-2.1.1-cp311-cp311-win_arm64.whl", hash = "sha256:c7659f22557c5a0bc4855cd635f55edec690cc008a40768527762cb9fb263455", size = 179941, upload-time = "2026-08-03T21:19:43.747Z" },
+    { url = "https://files.pythonhosted.org/packages/10/69/43965eccfdead3b9220015fd1320e117be8c6ed01a62ffab76eeb752f5d5/cffi-2.1.1-cp312-cp312-macosx_10_15_x86_64.whl", hash = "sha256:c8c69575568085ba0b1b10c0249d779a214aea6f6522e949a0fc9fb0fcb449d0", size = 184821, upload-time = "2026-08-03T21:19:44.887Z" },
+    { url = "https://files.pythonhosted.org/packages/54/7d/16e5a096677b5e313ca80cd5e5170efa3ea44624a82bb111925522da64b1/cffi-2.1.1-cp312-cp312-macosx_11_0_arm64.whl", hash = "sha256:f81b3b8f3d4e343550fa4baa0e479bba9f2d29ce9c2e9b51d1ce1718d7442fcf", size = 184719, upload-time = "2026-08-03T21:19:46.129Z" },
+    { url = "https://files.pythonhosted.org/packages/56/e6/8941622732edec876dd17d0453dce07317ae96db34f2ec1436c9d3785986/cffi-2.1.1-cp312-cp312-manylinux1_i686.manylinux2014_i686.manylinux_2_17_i686.manylinux_2_5_i686.whl", hash = "sha256:811bd1e21d32de12efca32393a0ab3f5133b54fce9bd44b8bd77ab07da14bf6a", size = 214799, upload-time = "2026-08-03T21:19:47.218Z" },
+    { url = "https://files.pythonhosted.org/packages/44/de/f98430906df1545ffde0d543dd124a7a439bc2cd32b36b9c53f805df7333/cffi-2.1.1-cp312-cp312-manylinux2014_aarch64.manylinux_2_17_aarch64.whl", hash = "sha256:68e62fe11f30d5ca8289242866f0a5291402d8529ca2178ab8afc5c9694ae890", size = 222389, upload-time = "2026-08-03T21:19:48.331Z" },
+    { url = "https://files.pythonhosted.org/packages/6a/5b/717f1526b9957b34456313c31645c5b82b8fb5c3fe9e4752999be7128bfc/cffi-2.1.1-cp312-cp312-manylinux2014_ppc64le.manylinux_2_17_ppc64le.whl", hash = "sha256:4a7c934f7360e8cd64fe9efadcbd10c7c6364f531e432b9a4bf5ccbc9e0e8b50", size = 210249, upload-time = "2026-08-03T21:19:49.543Z" },
+    { url = "https://files.pythonhosted.org/packages/64/b3/f8aa4f3e34986c7e4ec45072d1b1b9dd295b6b18007b45518d79726dd725/cffi-2.1.1-cp312-cp312-manylinux2014_s390x.manylinux_2_17_s390x.whl", hash = "sha256:3143d81e29e1e20a9ce10901ec369012947876596f75a222235965f2b7ae832e", size = 208775, upload-time = "2026-08-03T21:19:50.918Z" },
+    { url = "https://files.pythonhosted.org/packages/b1/db/dceb9dd5b231e1da801793f8acc9f3c52a7e1afe40bb1aae37e02b0faad5/cffi-2.1.1-cp312-cp312-manylinux2014_x86_64.manylinux_2_17_x86_64.whl", hash = "sha256:c1453022f490d2459a11819d83ad1d586e9ff65a12ac3e705ffebd46d3685dcf", size = 221822, upload-time = "2026-08-03T21:19:52.054Z" },
+    { url = "https://files.pythonhosted.org/packages/a0/d2/6cd24ae3be000a634109c247d1475d62e5616d0dc78c82770942ec384248/cffi-2.1.1-cp312-cp312-musllinux_1_2_aarch64.whl", hash = "sha256:208f941bb9d18e768138677f0a6d2ce01f590df56043dda1df1535ac57c88517", size = 225232, upload-time = "2026-08-03T21:19:53.109Z" },
+    { url = "https://files.pythonhosted.org/packages/cb/52/3fa190537004dd7f0ab860a6dc7c0175b8667f68d1e618a46f5498d30250/cffi-2.1.1-cp312-cp312-musllinux_1_2_x86_64.whl", hash = "sha256:210019b6c7cf07f081b4c54635c8cf744377001350e29cc0f81c4377b4797735", size = 223597, upload-time = "2026-08-03T21:19:54.515Z" },
+    { url = "https://files.pythonhosted.org/packages/80/fb/0bb75b7039588c074b37ae99f40d9bfddf990ecb2fbc346ebccd2e56b9be/cffi-2.1.1-cp312-cp312-win32.whl", hash = "sha256:046bfc24911b37851ee1b51aab8bffe713d89c68c6a057b09484ce9fd5f69b4e", size = 175292, upload-time = "2026-08-03T21:19:55.566Z" },
+    { url = "https://files.pythonhosted.org/packages/d9/79/615cc094e2fb508cade7de88d3b4f6c4ec2bab695c97bce9153dc65aadf5/cffi-2.1.1-cp312-cp312-win_amd64.whl", hash = "sha256:f53e442b08449d42821fa4a4fba000095af9f62742a500f978a9f557ec44339a", size = 185919, upload-time = "2026-08-03T21:19:56.89Z" },
+    { url = "https://files.pythonhosted.org/packages/70/c6/d0ea84713fe46b243a436a18fcd47d639732747e21635c8a27191b06dc30/cffi-2.1.1-cp312-cp312-win_arm64.whl", hash = "sha256:7bde5e4cc5c10140859842b9d383af292b22639a4dffb725314baf45968cef80", size = 180093, upload-time = "2026-08-03T21:19:58.155Z" },
+    { url = "https://files.pythonhosted.org/packages/9d/f4/035513d4117049066b4779dc3b7c0c0fdad175fa13731c9f4003f1cd1478/cffi-2.1.1-cp313-cp313-ios_13_0_arm64_iphoneos.whl", hash = "sha256:b5bdfd1c873d4e093aabc0ca84c4ca6dbc4f752afb5c86f146d9742580c9da2e", size = 194248, upload-time = "2026-08-03T21:19:59.399Z" },
+    { url = "https://files.pythonhosted.org/packages/76/af/2aeb4dbb5fc41a04161ae9ff1518de7cec08e164f44a8ce6a4cf7fd2cd1d/cffi-2.1.1-cp313-cp313-ios_13_0_arm64_iphonesimulator.whl", hash = "sha256:31348097ff5bbe827ccc41795d4dd099d9f0625e7def00ee653c137a490c2a6c", size = 196908, upload-time = "2026-08-03T21:20:00.746Z" },
+    { url = "https://files.pythonhosted.org/packages/a7/46/2e5fdde8555706dd98139a910ca11be02809f3f605ce956f655d0214e100/cffi-2.1.1-cp313-cp313-macosx_10_15_x86_64.whl", hash = "sha256:9d2055050ea716bd38b7f7f1579c275386646b4894c155a3e2f3cd62ed41b7c6", size = 184805, upload-time = "2026-08-03T21:20:02.02Z" },
+    { url = "https://files.pythonhosted.org/packages/55/41/4c7042f317b9217502988f0873af87e16ad606dc20f84e546e3e6ce9764c/cffi-2.1.1-cp313-cp313-macosx_11_0_arm64.whl", hash = "sha256:19ee6127ee34de7d83ce3d371ebc5ed91addbdcc39f9ab15ce4eb35a4e534971", size = 184764, upload-time = "2026-08-03T21:20:03.141Z" },
+    { url = "https://files.pythonhosted.org/packages/43/1f/1c3d90d91811c8f86ced9ed637956c54bfe5b79ca98fe976d7f8c8979f6b/cffi-2.1.1-cp313-cp313-manylinux1_i686.manylinux2014_i686.manylinux_2_17_i686.manylinux_2_5_i686.whl", hash = "sha256:6a8dddef476fab96d066d578fc88526767b836ab5ab21754e1d5bf3879c31c7c", size = 214722, upload-time = "2026-08-03T21:20:04.377Z" },
+    { url = "https://files.pythonhosted.org/packages/37/6f/3b5ce4c3b2192d250f04908f2bfd91ef34552ec8f7716a5d4abdb8d67bb2/cffi-2.1.1-cp313-cp313-manylinux2014_aarch64.manylinux_2_17_aarch64.whl", hash = "sha256:f16c709686a78c727bbbf059f92b0bf41c6fc60deec706d2dc19f529175a6125", size = 222369, upload-time = "2026-08-03T21:20:05.544Z" },
+    { url = "https://files.pythonhosted.org/packages/02/10/4b3c75dde3d9663c9e02ba05c2668b954f671d4bbe346413ca8c696b295a/cffi-2.1.1-cp313-cp313-manylinux2014_ppc64le.manylinux_2_17_ppc64le.whl", hash = "sha256:fcd22650c908d7b7da162bbfaab594a1227a15d1643a98c68b122ac642fa2264", size = 210175, upload-time = "2026-08-03T21:20:06.75Z" },
+    { url = "https://files.pythonhosted.org/packages/df/62/14f74b9543e605d17701dc797b815958b8bb70b7624ce1b832ddad48ed6c/cffi-2.1.1-cp313-cp313-manylinux2014_s390x.manylinux_2_17_s390x.whl", hash = "sha256:aa9511c62d14da7aacc9b4bf51f3f697a621e83b2d6919008243c3aad168eea3", size = 208670, upload-time = "2026-08-03T21:20:08.04Z" },
+    { url = "https://files.pythonhosted.org/packages/95/95/86342356ff5953b3fb06f7ef7c5bee212d45e770abc7218d451b9148313c/cffi-2.1.1-cp313-cp313-manylinux2014_x86_64.manylinux_2_17_x86_64.whl", hash = "sha256:a931079504ecc49efed7744c476a5c343a92fabf66dec2db95edb1b2fdc770e2", size = 221824, upload-time = "2026-08-03T21:20:09.274Z" },
+    { url = "https://files.pythonhosted.org/packages/eb/ff/7b3429ff53aafe931ed8a5fc69f481bbef7ba6de87ddcbb63d08f483f613/cffi-2.1.1-cp313-cp313-musllinux_1_2_aarch64.whl", hash = "sha256:a2d7755bef5a12ed488f4ef1f1b69ee9191d7396083b755a5d2295f6edb4768b", size = 225148, upload-time = "2026-08-03T21:20:10.7Z" },
+    { url = "https://files.pythonhosted.org/packages/34/34/a95870b9221e09cf4f2ce3178b1a210abdfe63a1bd357da940418d7b8d15/cffi-2.1.1-cp313-cp313-musllinux_1_2_x86_64.whl", hash = "sha256:e0bcb7e0f677f543555d2adff3bf19c05f66cdb4796e5ff602442ab2fe3c4ef7", size = 223564, upload-time = "2026-08-03T21:20:12.165Z" },
+    { url = "https://files.pythonhosted.org/packages/70/ea/839b50531021a647fb5e929f72cf97bc1ff702b5472166164b5b6e76b851/cffi-2.1.1-cp313-cp313-win32.whl", hash = "sha256:334644fbac4eff73d985a17a91226df55d0f394160c4cfb880e084c8f7161cac", size = 175263, upload-time = "2026-08-03T21:20:13.559Z" },
+    { url = "https://files.pythonhosted.org/packages/60/a6/8b149b2c3f2e11aaa1618ef64500b45f50f22c57a977a4dff1aff1f91042/cffi-2.1.1-cp313-cp313-win_amd64.whl", hash = "sha256:1aa5645c30469b09530c4ebca77ebf8f17618293c58f8549cb1a543a50236e7d", size = 185688, upload-time = "2026-08-03T21:20:14.69Z" },
+    { url = "https://files.pythonhosted.org/packages/01/9a/11f687cb39d6a3504060d5242f04f48c735afb4d3d533958a20594890cb2/cffi-2.1.1-cp313-cp313-win_arm64.whl", hash = "sha256:63bbfd5ded17c4840ac07cd8f1c21ba9d9708141f840b324f422f41b207e3973", size = 180078, upload-time = "2026-08-03T21:20:15.917Z" },
+]
 
 [[package]]
 name = "colorama"
@@ -11,6 +143,93 @@ wheels = [
     { url = "https://files.pythonhosted.org/packages/d1/d6/3965ed04c63042e047cb6a3e6ed1a63a35087b6a609aa3a15ed8ac56c221/colorama-0.4.6-py2.py3-none-any.whl", hash = "sha256:4f1d9991f5acc0ca119f9d443620b77f9d6b33703e51011c16baf57afb285fc6", size = 25335, upload-time = "2022-10-25T02:36:20.889Z" },
 ]
 
+[[package]]
+name = "cryptography"
+version = "48.0.1"
+source = { registry = "https://pypi.org/simple" }
+dependencies = [
+    { name = "cffi", marker = "platform_python_implementation != 'PyPy'" },
+]
+sdist = { url = "https://files.pythonhosted.org/packages/12/45/870e7f4bef50e5f53b9f51d4428aee5290eedf58ba443f16b1ebb7ab8e66/cryptography-48.0.1.tar.gz", hash = "sha256:266f4ee051abb2f725b74ef8072b521ce1feacf685a3364fa6a6b45548db791a", size = 832989, upload-time = "2026-06-09T22:32:31.8Z" }
+wheels = [
+    { url = "https://files.pythonhosted.org/packages/1b/bc/ee4137cbbe105652c0ee4252792b78fc8e7afa4b8e61d9d5dc05a7f45731/cryptography-48.0.1-cp311-abi3-macosx_10_9_universal2.whl", hash = "sha256:3e4a1a3232eef2e6c732827d5722db29a0cc8b27af2a4d865b094cf954be9ca1", size = 8008324, upload-time = "2026-06-09T22:31:00.702Z" },
+    { url = "https://files.pythonhosted.org/packages/d5/85/6379d42181bfc713094f081360fc5784d6c816b599d45e7f082502d173ce/cryptography-48.0.1-cp311-abi3-manylinux2014_aarch64.manylinux_2_17_aarch64.whl", hash = "sha256:32143b24adb918f078134e1e230f1eb8cc04886b92c28b5f0041aaf3e5699225", size = 4696243, upload-time = "2026-06-09T22:32:33.446Z" },
+    { url = "https://files.pythonhosted.org/packages/9c/87/c85d147b53323c7eb4d850920c8901377323c2a0ff8d79c262d4fee89aa2/cryptography-48.0.1-cp311-abi3-manylinux2014_x86_64.manylinux_2_17_x86_64.whl", hash = "sha256:f0d27a5696721ef7a672b8c810f6aded391058e0b9486e63e6d93baf765da691", size = 4713235, upload-time = "2026-06-09T22:31:40.141Z" },
+    { url = "https://files.pythonhosted.org/packages/79/58/67cbf8cf1ee7c54b439ca07bbecf8362c07afc11a3724fea70f745784add/cryptography-48.0.1-cp311-abi3-manylinux_2_28_aarch64.whl", hash = "sha256:eb86ce1af36fe65041b6db9a8bb064ee621a7e5fded0f80d475ec243477cd242", size = 4702323, upload-time = "2026-06-09T22:31:42.191Z" },
+    { url = "https://files.pythonhosted.org/packages/89/c6/24266ac10c47f6cd2a865f4446062b466da1d1f10b27189eac00e61bf0c9/cryptography-48.0.1-cp311-abi3-manylinux_2_28_ppc64le.whl", hash = "sha256:b024e784ad6c077ee0147b35ea9cbfc1e34e1fd4c1dcca214c2794d73a12df08", size = 5300085, upload-time = "2026-06-09T22:31:58.703Z" },
+    { url = "https://files.pythonhosted.org/packages/d2/bb/cc4b78784f97efc8c5874c2a9743708d172be6663024b34a0467885ae0c8/cryptography-48.0.1-cp311-abi3-manylinux_2_28_x86_64.whl", hash = "sha256:3752f2dbc8f07a30aad2932c986cea495b03bb554887828225da104f732852b6", size = 4746137, upload-time = "2026-06-09T22:31:31.01Z" },
+    { url = "https://files.pythonhosted.org/packages/1f/52/0c44de3f5267f8fbe8e835138017522a333436166e406f0db9b9e6e3033f/cryptography-48.0.1-cp311-abi3-manylinux_2_31_armv7l.whl", hash = "sha256:bd81490cd5801d755cf97bb68ac191f14b708470b1c7cf4580f669b9c9264cd8", size = 4333867, upload-time = "2026-06-09T22:32:28.096Z" },
+    { url = "https://files.pythonhosted.org/packages/9a/2e/772d7adbfa931537bc401640b7cac9976bff689bda187833e5d63b428e49/cryptography-48.0.1-cp311-abi3-manylinux_2_34_aarch64.whl", hash = "sha256:66fd0771e7b9c6dcd44cf1120690d2338d16d72795cf40cae2786a39eba65429", size = 4701805, upload-time = "2026-06-09T22:31:38.284Z" },
+    { url = "https://files.pythonhosted.org/packages/f8/a3/b06844f303873493c963caf581c04df31c7035e0c1b0f02c4814d319ec80/cryptography-48.0.1-cp311-abi3-manylinux_2_34_ppc64le.whl", hash = "sha256:3fd2ca57062b241c856670b073487d2e86c4637937ca5601e48f97bf8e11fc8f", size = 5258461, upload-time = "2026-06-09T22:31:04.187Z" },
+    { url = "https://files.pythonhosted.org/packages/9f/13/8b765e2e12b07c74941caadb9d1c8fdc006c4dfbf2b8f2d610519758954d/cryptography-48.0.1-cp311-abi3-manylinux_2_34_x86_64.whl", hash = "sha256:0ee6ea481db1ab889cba043ec1eda17bb9c1ea79db6722f779c3667f9f70322f", size = 4745488, upload-time = "2026-06-09T22:32:30.07Z" },
+    { url = "https://files.pythonhosted.org/packages/2e/aa/48972bce55049b32a94f4907eda4d75fa385aad8a39506cc2fc72196ecf0/cryptography-48.0.1-cp311-abi3-musllinux_1_2_aarch64.whl", hash = "sha256:f2ceef93cb096aa3c4cc4b5c94ca6131f9196d28c64d6111533402a9b2054d41", size = 4830256, upload-time = "2026-06-09T22:31:43.868Z" },
+    { url = "https://files.pythonhosted.org/packages/47/a2/e5079a032fb85cf6005046ca92bbd78b0c82dad2b5751ab8c311659da06f/cryptography-48.0.1-cp311-abi3-musllinux_1_2_x86_64.whl", hash = "sha256:9bd3f92d76217892b15df84ca256c2c113d386fdda7a7d8691aeeced976507c6", size = 4979117, upload-time = "2026-06-09T22:31:05.845Z" },
+    { url = "https://files.pythonhosted.org/packages/b7/a0/8f50cae9c74e718ed769d63ed5c74bd0ea830c9550a74629cebd1b9c7bc7/cryptography-48.0.1-cp311-abi3-win32.whl", hash = "sha256:b9a32b876490d66c8bcc9963ef220199569748434ab01a9d6aaeabf88e7f5158", size = 3304154, upload-time = "2026-06-09T22:32:16.845Z" },
+    { url = "https://files.pythonhosted.org/packages/c5/69/0572c77dbace6fef72f33755bd52ea399c71367250d366237f8691826b9e/cryptography-48.0.1-cp311-abi3-win_amd64.whl", hash = "sha256:39489bfca54c7a1f6b297efcd8bc608ab92d16c4ca631b0cad4da46724588b24", size = 3817138, upload-time = "2026-06-09T22:32:00.388Z" },
+    { url = "https://files.pythonhosted.org/packages/ca/6c/00fa2a95997164c8b2072ce327c23d4ab20809ccc323ea5fab91e53a4bba/cryptography-48.0.1-cp39-abi3-macosx_10_9_universal2.whl", hash = "sha256:4fdc69f8e4316bcf0c8c8ec1f26f285d12e8142d88d96c876a59a03be3f6ae67", size = 7987408, upload-time = "2026-06-09T22:32:20.777Z" },
+    { url = "https://files.pythonhosted.org/packages/b0/d9/45f309a7e4e5f3f8f121d6d3be9e94024a7726ec598d6e08ae04edb2f04d/cryptography-48.0.1-cp39-abi3-manylinux2014_aarch64.manylinux_2_17_aarch64.whl", hash = "sha256:48fe40804d4caa2288f24e70ca8c64c42dd826da0ad7e4f1b41b2128d679e6c8", size = 4690196, upload-time = "2026-06-09T22:31:54.74Z" },
+    { url = "https://files.pythonhosted.org/packages/5f/9f/a1bc8bcc798811b8527eb374bbccf30a3f3e806829d967118222bf1125eb/cryptography-48.0.1-cp39-abi3-manylinux2014_x86_64.manylinux_2_17_x86_64.whl", hash = "sha256:86be3b1b0b6bf09482fb50a979c508d2950ed95f5621ec77f4e385962006b83a", size = 4696782, upload-time = "2026-06-09T22:31:45.615Z" },
+    { url = "https://files.pythonhosted.org/packages/66/c2/81a4fb4e4373c500bb526bc337ac5719dd31dd15b970b84a238168c6aa08/cryptography-48.0.1-cp39-abi3-manylinux_2_28_aarch64.whl", hash = "sha256:4ab0a343c807bbcd90c971cd1ecf072937cd01847a9e002bef88fb47ac6be577", size = 4696618, upload-time = "2026-06-09T22:31:11.564Z" },
+    { url = "https://files.pythonhosted.org/packages/e5/0b/aa68b221dde92d09cb29a024ede17550ee21e77a404e59fc093c82bb51e1/cryptography-48.0.1-cp39-abi3-manylinux_2_28_ppc64le.whl", hash = "sha256:9621de99d2da096006b629979efd8ae7eb2d8b822488d0c89ee4000c306c59b1", size = 5289970, upload-time = "2026-06-09T22:31:20.368Z" },
+    { url = "https://files.pythonhosted.org/packages/78/13/fba657f958d2af66ea959a4ba01212632089249d34af1ae48054136344d7/cryptography-48.0.1-cp39-abi3-manylinux_2_28_x86_64.whl", hash = "sha256:88c852a0ae366e262e5a1744b685e6a433dc8788dd2a277e418bf4904203609d", size = 4731873, upload-time = "2026-06-09T22:31:22.253Z" },
+    { url = "https://files.pythonhosted.org/packages/4c/4c/9a964756d24a26b3e34dfcb16f961b89838786e6700b635b0d1e3adff4b6/cryptography-48.0.1-cp39-abi3-manylinux_2_31_armv7l.whl", hash = "sha256:43c5835e2cb98c8733d86f57d6fc879b613f5c3478607281c3e36daffc6dd8a6", size = 4330804, upload-time = "2026-06-09T22:31:36.56Z" },
+    { url = "https://files.pythonhosted.org/packages/4b/0f/a10f3a6eb12950a10e3a874070283aa2dd5875b2bfd15fad8a3e17b3f13e/cryptography-48.0.1-cp39-abi3-manylinux_2_34_aarch64.whl", hash = "sha256:fe0180af5bf9236518a087e35bf2d9a347d5f5f51e63c579d683ddff424e3d46", size = 4696217, upload-time = "2026-06-09T22:31:13.351Z" },
+    { url = "https://files.pythonhosted.org/packages/f3/6f/5cd12f951165ea73ef85266775d97e4c763b2474ccfd816dd69d3a18d6f8/cryptography-48.0.1-cp39-abi3-manylinux_2_34_ppc64le.whl", hash = "sha256:b7a2d1a937a738a881737cec135a38bb61470589b17515b9f73f571d0ae10401", size = 5245252, upload-time = "2026-06-09T22:32:02.193Z" },
+    { url = "https://files.pythonhosted.org/packages/68/ab/8aaa12e4516ec4464033ab79b6f3b592bd5a92102467c4ace8a0d970203f/cryptography-48.0.1-cp39-abi3-manylinux_2_34_x86_64.whl", hash = "sha256:b74ca3b8e5ecdd833bf6a002ca41b4793bb27fb8f1c06ffaf2643c9e9140e31b", size = 4731388, upload-time = "2026-06-09T22:32:04.019Z" },
+    { url = "https://files.pythonhosted.org/packages/1b/24/50027ea4dca85ec1f40688f3c24fb32ccacd520583c9592c3cc95628e6fb/cryptography-48.0.1-cp39-abi3-musllinux_1_2_aarch64.whl", hash = "sha256:2c37f2461406063b417837f5f3daab668652acd82423efcd7f0a9f04be972de1", size = 4824186, upload-time = "2026-06-09T22:32:18.707Z" },
+    { url = "https://files.pythonhosted.org/packages/52/41/04cb5eb17085ade6f50cc611fb657df6a0f5885350de8764ece89c050197/cryptography-48.0.1-cp39-abi3-musllinux_1_2_x86_64.whl", hash = "sha256:86fe77abb1bd87afb251d4d02ada7ecf53a32cee9b67d976abb2e45a13297475", size = 4964539, upload-time = "2026-06-09T22:31:18.793Z" },
+    { url = "https://files.pythonhosted.org/packages/36/bf/ed70785c496e89d7e73b7cda2d21f2447fd6d4e821714b8d04ff217fed92/cryptography-48.0.1-cp39-abi3-win32.whl", hash = "sha256:6b2c0c3e6ccf3ade7750f836ef3ee36eea250cc467d45c256895573ac08cc6f1", size = 3282307, upload-time = "2026-06-09T22:30:53.162Z" },
+    { url = "https://files.pythonhosted.org/packages/b3/ff/371ea7d252656ee1eb6d83eeeef3d1d0c6baf1d6497687d081ea03814670/cryptography-48.0.1-cp39-abi3-win_amd64.whl", hash = "sha256:9a49ca6c81417f6a5edb50375a60cccdd70fa0a91a5211829dbea74eba94d2ac", size = 3793408, upload-time = "2026-06-09T22:32:15.191Z" },
+    { url = "https://files.pythonhosted.org/packages/a9/d3/eb4e394e587341fdad09a09101fa76478ead3a78b0ad63e55c22f0d75c02/cryptography-48.0.1-pp311-pypy311_pp73-macosx_11_0_arm64.whl", hash = "sha256:08a597acce1ff37f347400087776599e2348a3a8bc53b44120e463cd274efe4a", size = 3951747, upload-time = "2026-06-09T22:31:23.871Z" },
+    { url = "https://files.pythonhosted.org/packages/e0/4a/3f43451b4f858bfceaaaffc649e6e787e8d4fb332a1d443af39ab02cc8f1/cryptography-48.0.1-pp311-pypy311_pp73-manylinux_2_28_aarch64.whl", hash = "sha256:735824ec41b7f74a7c45fb1591349333e4c696cb6c044e5f46356e560143e4cd", size = 4641226, upload-time = "2026-06-09T22:31:02.532Z" },
+    { url = "https://files.pythonhosted.org/packages/73/4e/855584c2c23b09e4ce2d3b9c30e983e679cd60b068c513c6bbdb91e11782/cryptography-48.0.1-pp311-pypy311_pp73-manylinux_2_28_x86_64.whl", hash = "sha256:92a46e1d638daa264ba2971c0b0489c9409787943efae4d60ffda3d091ef832c", size = 4668958, upload-time = "2026-06-09T22:32:06.213Z" },
+    { url = "https://files.pythonhosted.org/packages/42/3b/d35750e41d803d1e516fd6d6011f065424924da7af1748cef4cc9cb3ede1/cryptography-48.0.1-pp311-pypy311_pp73-manylinux_2_34_aarch64.whl", hash = "sha256:7e234ac052af99f2700826a5c29ea99d9c1b1f80341cde62d11c8154dc8e0bd9", size = 4640793, upload-time = "2026-06-09T22:32:26.331Z" },
+    { url = "https://files.pythonhosted.org/packages/ca/aa/cdb7181fe865285e87e96825aaab239400f1de0c3bfba9bd9769b79f1a92/cryptography-48.0.1-pp311-pypy311_pp73-manylinux_2_34_x86_64.whl", hash = "sha256:33842cf0888951cef5bc7ac724ab844a42044c1727b967b7f8997289a0464f92", size = 4668505, upload-time = "2026-06-09T22:31:27.534Z" },
+    { url = "https://files.pythonhosted.org/packages/5d/8c/ce3823c06c2804f194f9e64f0d67fa3f4094a39f2bb1a990cd03603af8fc/cryptography-48.0.1-pp311-pypy311_pp73-win_amd64.whl", hash = "sha256:6184ca7b174f28d7c703f1290d4b297217c45355f77a98f67e9b7f14549ac54a", size = 3742204, upload-time = "2026-06-09T22:31:34.773Z" },
+]
+
+[[package]]
+name = "ecdsa"
+version = "0.19.2"
+source = { registry = "https://pypi.org/simple" }
+dependencies = [
+    { name = "six" },
+]
+sdist = { url = "https://files.pythonhosted.org/packages/25/ca/8de7744cb3bc966c85430ca2d0fcaeea872507c6a4cf6e007f7fe269ed9d/ecdsa-0.19.2.tar.gz", hash = "sha256:62635b0ac1ca2e027f82122b5b81cb706edc38cd91c63dda28e4f3455a2bf930", size = 202432, upload-time = "2026-03-26T09:58:17.675Z" }
+wheels = [
+    { url = "https://files.pythonhosted.org/packages/51/79/119091c98e2bf49e24ed9f3ae69f816d715d2904aefa6a2baa039a2ba0b0/ecdsa-0.19.2-py2.py3-none-any.whl", hash = "sha256:840f5dc5e375c68f36c1a7a5b9caad28f95daa65185c9253c0c08dd952bb7399", size = 150818, upload-time = "2026-03-26T09:58:15.808Z" },
+]
+
+[[package]]
+name = "esptool"
+version = "4.12.0"
+source = { registry = "https://pypi.org/simple" }
+dependencies = [
+    { name = "argcomplete", marker = "sys_platform != 'win32'" },
+    { name = "bitstring" },
+    { name = "cryptography" },
+    { name = "ecdsa" },
+    { name = "intelhex" },
+    { name = "pyserial" },
+    { name = "pyyaml" },
+    { name = "reedsolo" },
+]
+sdist = { url = "https://files.pythonhosted.org/packages/84/19/f68b27fd43564d69277e956d13b8c2b352e7f1af4fb5d6e5c43e5419e61c/esptool-4.12.0.tar.gz", hash = "sha256:d797f6529d582173508baf0572542ddadf53aae8c92c84ea9f420f242464103c", size = 463840, upload-time = "2026-07-14T08:36:51.891Z" }
+
+[[package]]
+name = "fs"
+version = "2.4.16"
+source = { registry = "https://pypi.org/simple" }
+dependencies = [
+    { name = "appdirs" },
+    { name = "setuptools" },
+    { name = "six" },
+]
+sdist = { url = "https://files.pythonhosted.org/packages/5d/a9/af5bfd5a92592c16cdae5c04f68187a309be8a146b528eac3c6e30edbad2/fs-2.4.16.tar.gz", hash = "sha256:ae97c7d51213f4b70b6a958292530289090de3a7e15841e108fbe144f069d313", size = 187441, upload-time = "2022-05-02T09:25:54.22Z" }
+wheels = [
+    { url = "https://files.pythonhosted.org/packages/b9/5c/a3d95dc1ec6cdeb032d789b552ecc76effa3557ea9186e1566df6aac18df/fs-2.4.16-py2.py3-none-any.whl", hash = "sha256:660064febbccda264ae0b6bace80a8d1be9e089e0a5eb2427b7d517f9a91545c", size = 135261, upload-time = "2022-05-02T09:25:52.363Z" },
+]
+
 [[package]]
 name = "iniconfig"
 version = "2.3.0"
@@ -20,28 +239,47 @@ wheels = [
     { url = "https://files.pythonhosted.org/packages/cb/b1/3846dd7f199d53cb17f49cba7e651e9ce294d8497c8c150530ed11865bb8/iniconfig-2.3.0-py3-none-any.whl", hash = "sha256:f631c04d2c48c52b84d0d0549c99ff3859c98df65b3101406327ecc7d53fbf12", size = 7484, upload-time = "2025-10-18T21:55:41.639Z" },
 ]
 
+[[package]]
+name = "intelhex"
+version = "2.3.0"
+source = { registry = "https://pypi.org/simple" }
+sdist = { url = "https://files.pythonhosted.org/packages/66/37/1e7522494557d342a24cb236e2aec5d078fac8ed03ad4b61372586406b01/intelhex-2.3.0.tar.gz", hash = "sha256:892b7361a719f4945237da8ccf754e9513db32f5628852785aea108dcd250093", size = 44513, upload-time = "2020-10-20T20:35:51.526Z" }
+wheels = [
+    { url = "https://files.pythonhosted.org/packages/97/78/79461288da2b13ed0a13deb65c4ad1428acb674b95278fa9abf1cefe62a2/intelhex-2.3.0-py2.py3-none-any.whl", hash = "sha256:87cc5225657524ec6361354be928adfd56bcf2a3dcc646c40f8f094c39c07db4", size = 50914, upload-time = "2020-10-20T20:35:50.162Z" },
+]
+
 [[package]]
 name = "kota-technician-tool"
-version = "0.1.0"
+version = "0.6.0"
 source = { virtual = "." }
 dependencies = [
+    { name = "esptool" },
     { name = "pyserial" },
     { name = "pyside6-essentials" },
+    { name = "segno" },
 ]
 
 [package.dev-dependencies]
 dev = [
+    { name = "pyfatfs" },
     { name = "pytest" },
+    { name = "setuptools" },
 ]
 
 [package.metadata]
 requires-dist = [
+    { name = "esptool", specifier = "~=4.8" },
     { name = "pyserial", specifier = ">=3.5" },
     { name = "pyside6-essentials", specifier = ">=6.7" },
+    { name = "segno", specifier = ">=1.6" },
 ]
 
 [package.metadata.requires-dev]
-dev = [{ name = "pytest", specifier = ">=8" }]
+dev = [
+    { name = "pyfatfs", specifier = ">=1.0" },
+    { name = "pytest", specifier = ">=8" },
+    { name = "setuptools", specifier = "<81" },
+]
 
 [[package]]
 name = "packaging"
@@ -61,6 +299,27 @@ wheels = [
     { url = "https://files.pythonhosted.org/packages/54/20/4d324d65cc6d9205fabedc306948156824eb9f0ee1633355a8f7ec5c66bf/pluggy-1.6.0-py3-none-any.whl", hash = "sha256:e920276dd6813095e9377c0bc5566d94c932c33b27a3e3945d8389c374dd4746", size = 20538, upload-time = "2025-05-15T12:30:06.134Z" },
 ]
 
+[[package]]
+name = "pycparser"
+version = "3.0"
+source = { registry = "https://pypi.org/simple" }
+sdist = { url = "https://files.pythonhosted.org/packages/1b/7d/92392ff7815c21062bea51aa7b87d45576f649f16458d78b7cf94b9ab2e6/pycparser-3.0.tar.gz", hash = "sha256:600f49d217304a5902ac3c37e1281c9fe94e4d0489de643a9504c5cdfdfc6b29", size = 103492, upload-time = "2026-01-21T14:26:51.89Z" }
+wheels = [
+    { url = "https://files.pythonhosted.org/packages/0c/c3/44f3fbbfa403ea2a7c779186dc20772604442dde72947e7d01069cbe98e3/pycparser-3.0-py3-none-any.whl", hash = "sha256:b727414169a36b7d524c1c3e31839a521725078d7b2ff038656844266160a992", size = 48172, upload-time = "2026-01-21T14:26:50.693Z" },
+]
+
+[[package]]
+name = "pyfatfs"
+version = "1.1.0"
+source = { registry = "https://pypi.org/simple" }
+dependencies = [
+    { name = "fs" },
+]
+sdist = { url = "https://files.pythonhosted.org/packages/44/3f/d08f1dbc44a7eef9c7fb355b83423fbd15bb3e487c250479a2c179cb39bf/pyfatfs-1.1.0.tar.gz", hash = "sha256:9725ccd0a4da1c09c27358abbf10f08c043ac84210af576803e087f51a2b30e0", size = 55459, upload-time = "2024-03-03T20:50:43.227Z" }
+wheels = [
+    { url = "https://files.pythonhosted.org/packages/cb/de/feb531b25eb2315aa73a7dba335c253ee0075ff7f55b6fe742fb6d492ade/pyfatfs-1.1.0-py3-none-any.whl", hash = "sha256:7401fd39d9e92f531b2abea5b5d1d2c19d5461f4ba9ce8819b1ba35aea73c65d", size = 37932, upload-time = "2024-03-03T20:50:41.426Z" },
+]
+
 [[package]]
 name = "pygments"
 version = "2.21.0"
@@ -110,6 +369,70 @@ wheels = [
     { url = "https://files.pythonhosted.org/packages/24/25/1de2678b631f5a49215c6c96fff41ba892b0a34df68d6d80292b1b48aa7f/pytest-9.1.1-py3-none-any.whl", hash = "sha256:37a86b45efb9a47a61a36449063e8e18d0cab3161329fc099eb21783169c4f0c", size = 386536, upload-time = "2026-06-19T10:58:31.347Z" },
 ]
 
+[[package]]
+name = "pyyaml"
+version = "6.0.3"
+source = { registry = "https://pypi.org/simple" }
+sdist = { url = "https://files.pythonhosted.org/packages/05/8e/961c0007c59b8dd7729d542c61a4d537767a59645b82a0b521206e1e25c2/pyyaml-6.0.3.tar.gz", hash = "sha256:d76623373421df22fb4cf8817020cbb7ef15c725b9d5e45f17e189bfc384190f", size = 130960, upload-time = "2025-09-25T21:33:16.546Z" }
+wheels = [
+    { url = "https://files.pythonhosted.org/packages/6d/16/a95b6757765b7b031c9374925bb718d55e0a9ba8a1b6a12d25962ea44347/pyyaml-6.0.3-cp311-cp311-macosx_10_13_x86_64.whl", hash = "sha256:44edc647873928551a01e7a563d7452ccdebee747728c1080d881d68af7b997e", size = 185826, upload-time = "2025-09-25T21:31:58.655Z" },
+    { url = "https://files.pythonhosted.org/packages/16/19/13de8e4377ed53079ee996e1ab0a9c33ec2faf808a4647b7b4c0d46dd239/pyyaml-6.0.3-cp311-cp311-macosx_11_0_arm64.whl", hash = "sha256:652cb6edd41e718550aad172851962662ff2681490a8a711af6a4d288dd96824", size = 175577, upload-time = "2025-09-25T21:32:00.088Z" },
+    { url = "https://files.pythonhosted.org/packages/0c/62/d2eb46264d4b157dae1275b573017abec435397aa59cbcdab6fc978a8af4/pyyaml-6.0.3-cp311-cp311-manylinux2014_aarch64.manylinux_2_17_aarch64.manylinux_2_28_aarch64.whl", hash = "sha256:10892704fc220243f5305762e276552a0395f7beb4dbf9b14ec8fd43b57f126c", size = 775556, upload-time = "2025-09-25T21:32:01.31Z" },
+    { url = "https://files.pythonhosted.org/packages/10/cb/16c3f2cf3266edd25aaa00d6c4350381c8b012ed6f5276675b9eba8d9ff4/pyyaml-6.0.3-cp311-cp311-manylinux2014_s390x.manylinux_2_17_s390x.manylinux_2_28_s390x.whl", hash = "sha256:850774a7879607d3a6f50d36d04f00ee69e7fc816450e5f7e58d7f17f1ae5c00", size = 882114, upload-time = "2025-09-25T21:32:03.376Z" },
+    { url = "https://files.pythonhosted.org/packages/71/60/917329f640924b18ff085ab889a11c763e0b573da888e8404ff486657602/pyyaml-6.0.3-cp311-cp311-manylinux2014_x86_64.manylinux_2_17_x86_64.manylinux_2_28_x86_64.whl", hash = "sha256:b8bb0864c5a28024fac8a632c443c87c5aa6f215c0b126c449ae1a150412f31d", size = 806638, upload-time = "2025-09-25T21:32:04.553Z" },
+    { url = "https://files.pythonhosted.org/packages/dd/6f/529b0f316a9fd167281a6c3826b5583e6192dba792dd55e3203d3f8e655a/pyyaml-6.0.3-cp311-cp311-musllinux_1_2_aarch64.whl", hash = "sha256:1d37d57ad971609cf3c53ba6a7e365e40660e3be0e5175fa9f2365a379d6095a", size = 767463, upload-time = "2025-09-25T21:32:06.152Z" },
+    { url = "https://files.pythonhosted.org/packages/f2/6a/b627b4e0c1dd03718543519ffb2f1deea4a1e6d42fbab8021936a4d22589/pyyaml-6.0.3-cp311-cp311-musllinux_1_2_x86_64.whl", hash = "sha256:37503bfbfc9d2c40b344d06b2199cf0e96e97957ab1c1b546fd4f87e53e5d3e4", size = 794986, upload-time = "2025-09-25T21:32:07.367Z" },
+    { url = "https://files.pythonhosted.org/packages/45/91/47a6e1c42d9ee337c4839208f30d9f09caa9f720ec7582917b264defc875/pyyaml-6.0.3-cp311-cp311-win32.whl", hash = "sha256:8098f252adfa6c80ab48096053f512f2321f0b998f98150cea9bd23d83e1467b", size = 142543, upload-time = "2025-09-25T21:32:08.95Z" },
+    { url = "https://files.pythonhosted.org/packages/da/e3/ea007450a105ae919a72393cb06f122f288ef60bba2dc64b26e2646fa315/pyyaml-6.0.3-cp311-cp311-win_amd64.whl", hash = "sha256:9f3bfb4965eb874431221a3ff3fdcddc7e74e3b07799e0e84ca4a0f867d449bf", size = 158763, upload-time = "2025-09-25T21:32:09.96Z" },
+    { url = "https://files.pythonhosted.org/packages/d1/33/422b98d2195232ca1826284a76852ad5a86fe23e31b009c9886b2d0fb8b2/pyyaml-6.0.3-cp312-cp312-macosx_10_13_x86_64.whl", hash = "sha256:7f047e29dcae44602496db43be01ad42fc6f1cc0d8cd6c83d342306c32270196", size = 182063, upload-time = "2025-09-25T21:32:11.445Z" },
+    { url = "https://files.pythonhosted.org/packages/89/a0/6cf41a19a1f2f3feab0e9c0b74134aa2ce6849093d5517a0c550fe37a648/pyyaml-6.0.3-cp312-cp312-macosx_11_0_arm64.whl", hash = "sha256:fc09d0aa354569bc501d4e787133afc08552722d3ab34836a80547331bb5d4a0", size = 173973, upload-time = "2025-09-25T21:32:12.492Z" },
+    { url = "https://files.pythonhosted.org/packages/ed/23/7a778b6bd0b9a8039df8b1b1d80e2e2ad78aa04171592c8a5c43a56a6af4/pyyaml-6.0.3-cp312-cp312-manylinux2014_aarch64.manylinux_2_17_aarch64.manylinux_2_28_aarch64.whl", hash = "sha256:9149cad251584d5fb4981be1ecde53a1ca46c891a79788c0df828d2f166bda28", size = 775116, upload-time = "2025-09-25T21:32:13.652Z" },
+    { url = "https://files.pythonhosted.org/packages/65/30/d7353c338e12baef4ecc1b09e877c1970bd3382789c159b4f89d6a70dc09/pyyaml-6.0.3-cp312-cp312-manylinux2014_s390x.manylinux_2_17_s390x.manylinux_2_28_s390x.whl", hash = "sha256:5fdec68f91a0c6739b380c83b951e2c72ac0197ace422360e6d5a959d8d97b2c", size = 844011, upload-time = "2025-09-25T21:32:15.21Z" },
+    { url = "https://files.pythonhosted.org/packages/8b/9d/b3589d3877982d4f2329302ef98a8026e7f4443c765c46cfecc8858c6b4b/pyyaml-6.0.3-cp312-cp312-manylinux2014_x86_64.manylinux_2_17_x86_64.manylinux_2_28_x86_64.whl", hash = "sha256:ba1cc08a7ccde2d2ec775841541641e4548226580ab850948cbfda66a1befcdc", size = 807870, upload-time = "2025-09-25T21:32:16.431Z" },
+    { url = "https://files.pythonhosted.org/packages/05/c0/b3be26a015601b822b97d9149ff8cb5ead58c66f981e04fedf4e762f4bd4/pyyaml-6.0.3-cp312-cp312-musllinux_1_2_aarch64.whl", hash = "sha256:8dc52c23056b9ddd46818a57b78404882310fb473d63f17b07d5c40421e47f8e", size = 761089, upload-time = "2025-09-25T21:32:17.56Z" },
+    { url = "https://files.pythonhosted.org/packages/be/8e/98435a21d1d4b46590d5459a22d88128103f8da4c2d4cb8f14f2a96504e1/pyyaml-6.0.3-cp312-cp312-musllinux_1_2_x86_64.whl", hash = "sha256:41715c910c881bc081f1e8872880d3c650acf13dfa8214bad49ed4cede7c34ea", size = 790181, upload-time = "2025-09-25T21:32:18.834Z" },
+    { url = "https://files.pythonhosted.org/packages/74/93/7baea19427dcfbe1e5a372d81473250b379f04b1bd3c4c5ff825e2327202/pyyaml-6.0.3-cp312-cp312-win32.whl", hash = "sha256:96b533f0e99f6579b3d4d4995707cf36df9100d67e0c8303a0c55b27b5f99bc5", size = 137658, upload-time = "2025-09-25T21:32:20.209Z" },
+    { url = "https://files.pythonhosted.org/packages/86/bf/899e81e4cce32febab4fb42bb97dcdf66bc135272882d1987881a4b519e9/pyyaml-6.0.3-cp312-cp312-win_amd64.whl", hash = "sha256:5fcd34e47f6e0b794d17de1b4ff496c00986e1c83f7ab2fb8fcfe9616ff7477b", size = 154003, upload-time = "2025-09-25T21:32:21.167Z" },
+    { url = "https://files.pythonhosted.org/packages/1a/08/67bd04656199bbb51dbed1439b7f27601dfb576fb864099c7ef0c3e55531/pyyaml-6.0.3-cp312-cp312-win_arm64.whl", hash = "sha256:64386e5e707d03a7e172c0701abfb7e10f0fb753ee1d773128192742712a98fd", size = 140344, upload-time = "2025-09-25T21:32:22.617Z" },
+    { url = "https://files.pythonhosted.org/packages/d1/11/0fd08f8192109f7169db964b5707a2f1e8b745d4e239b784a5a1dd80d1db/pyyaml-6.0.3-cp313-cp313-macosx_10_13_x86_64.whl", hash = "sha256:8da9669d359f02c0b91ccc01cac4a67f16afec0dac22c2ad09f46bee0697eba8", size = 181669, upload-time = "2025-09-25T21:32:23.673Z" },
+    { url = "https://files.pythonhosted.org/packages/b1/16/95309993f1d3748cd644e02e38b75d50cbc0d9561d21f390a76242ce073f/pyyaml-6.0.3-cp313-cp313-macosx_11_0_arm64.whl", hash = "sha256:2283a07e2c21a2aa78d9c4442724ec1eb15f5e42a723b99cb3d822d48f5f7ad1", size = 173252, upload-time = "2025-09-25T21:32:25.149Z" },
+    { url = "https://files.pythonhosted.org/packages/50/31/b20f376d3f810b9b2371e72ef5adb33879b25edb7a6d072cb7ca0c486398/pyyaml-6.0.3-cp313-cp313-manylinux2014_aarch64.manylinux_2_17_aarch64.manylinux_2_28_aarch64.whl", hash = "sha256:ee2922902c45ae8ccada2c5b501ab86c36525b883eff4255313a253a3160861c", size = 767081, upload-time = "2025-09-25T21:32:26.575Z" },
+    { url = "https://files.pythonhosted.org/packages/49/1e/a55ca81e949270d5d4432fbbd19dfea5321eda7c41a849d443dc92fd1ff7/pyyaml-6.0.3-cp313-cp313-manylinux2014_s390x.manylinux_2_17_s390x.manylinux_2_28_s390x.whl", hash = "sha256:a33284e20b78bd4a18c8c2282d549d10bc8408a2a7ff57653c0cf0b9be0afce5", size = 841159, upload-time = "2025-09-25T21:32:27.727Z" },
+    { url = "https://files.pythonhosted.org/packages/74/27/e5b8f34d02d9995b80abcef563ea1f8b56d20134d8f4e5e81733b1feceb2/pyyaml-6.0.3-cp313-cp313-manylinux2014_x86_64.manylinux_2_17_x86_64.manylinux_2_28_x86_64.whl", hash = "sha256:0f29edc409a6392443abf94b9cf89ce99889a1dd5376d94316ae5145dfedd5d6", size = 801626, upload-time = "2025-09-25T21:32:28.878Z" },
+    { url = "https://files.pythonhosted.org/packages/f9/11/ba845c23988798f40e52ba45f34849aa8a1f2d4af4b798588010792ebad6/pyyaml-6.0.3-cp313-cp313-musllinux_1_2_aarch64.whl", hash = "sha256:f7057c9a337546edc7973c0d3ba84ddcdf0daa14533c2065749c9075001090e6", size = 753613, upload-time = "2025-09-25T21:32:30.178Z" },
+    { url = "https://files.pythonhosted.org/packages/3d/e0/7966e1a7bfc0a45bf0a7fb6b98ea03fc9b8d84fa7f2229e9659680b69ee3/pyyaml-6.0.3-cp313-cp313-musllinux_1_2_x86_64.whl", hash = "sha256:eda16858a3cab07b80edaf74336ece1f986ba330fdb8ee0d6c0d68fe82bc96be", size = 794115, upload-time = "2025-09-25T21:32:31.353Z" },
+    { url = "https://files.pythonhosted.org/packages/de/94/980b50a6531b3019e45ddeada0626d45fa85cbe22300844a7983285bed3b/pyyaml-6.0.3-cp313-cp313-win32.whl", hash = "sha256:d0eae10f8159e8fdad514efdc92d74fd8d682c933a6dd088030f3834bc8e6b26", size = 137427, upload-time = "2025-09-25T21:32:32.58Z" },
+    { url = "https://files.pythonhosted.org/packages/97/c9/39d5b874e8b28845e4ec2202b5da735d0199dbe5b8fb85f91398814a9a46/pyyaml-6.0.3-cp313-cp313-win_amd64.whl", hash = "sha256:79005a0d97d5ddabfeeea4cf676af11e647e41d81c9a7722a193022accdb6b7c", size = 154090, upload-time = "2025-09-25T21:32:33.659Z" },
+    { url = "https://files.pythonhosted.org/packages/73/e8/2bdf3ca2090f68bb3d75b44da7bbc71843b19c9f2b9cb9b0f4ab7a5a4329/pyyaml-6.0.3-cp313-cp313-win_arm64.whl", hash = "sha256:5498cd1645aa724a7c71c8f378eb29ebe23da2fc0d7a08071d89469bf1d2defb", size = 140246, upload-time = "2025-09-25T21:32:34.663Z" },
+]
+
+[[package]]
+name = "reedsolo"
+version = "1.7.0"
+source = { registry = "https://pypi.org/simple" }
+sdist = { url = "https://files.pythonhosted.org/packages/f7/61/a67338cbecf370d464e71b10e9a31355f909d6937c3a8d6b17dd5d5beb5e/reedsolo-1.7.0.tar.gz", hash = "sha256:c1359f02742751afe0f1c0de9f0772cc113835aa2855d2db420ea24393c87732", size = 59723, upload-time = "2023-01-17T05:10:19.733Z" }
+wheels = [
+    { url = "https://files.pythonhosted.org/packages/09/19/1bb346c0e581557c88946d2bb979b2bee8992e72314cfb418b5440e383db/reedsolo-1.7.0-py3-none-any.whl", hash = "sha256:2b6a3e402a1ee3e1eea3f932f81e6c0b7bbc615588074dca1dbbcdeb055002bd", size = 32360, upload-time = "2023-01-17T05:10:17.652Z" },
+]
+
+[[package]]
+name = "segno"
+version = "1.6.6"
+source = { registry = "https://pypi.org/simple" }
+sdist = { url = "https://files.pythonhosted.org/packages/1c/2e/b396f750c53f570055bf5a9fc1ace09bed2dff013c73b7afec5702a581ba/segno-1.6.6.tar.gz", hash = "sha256:e60933afc4b52137d323a4434c8340e0ce1e58cec71439e46680d4db188f11b3", size = 1628586, upload-time = "2025-03-12T22:12:53.324Z" }
+wheels = [
+    { url = "https://files.pythonhosted.org/packages/d6/02/12c73fd423eb9577b97fc1924966b929eff7074ae6b2e15dd3d30cb9e4ae/segno-1.6.6-py3-none-any.whl", hash = "sha256:28c7d081ed0cf935e0411293a465efd4d500704072cdb039778a2ab8736190c7", size = 76503, upload-time = "2025-03-12T22:12:48.106Z" },
+]
+
+[[package]]
+name = "setuptools"
+version = "80.10.2"
+source = { registry = "https://pypi.org/simple" }
+sdist = { url = "https://files.pythonhosted.org/packages/76/95/faf61eb8363f26aa7e1d762267a8d602a1b26d4f3a1e758e92cb3cb8b054/setuptools-80.10.2.tar.gz", hash = "sha256:8b0e9d10c784bf7d262c4e5ec5d4ec94127ce206e8738f29a437945fbc219b70", size = 1200343, upload-time = "2026-01-25T22:38:17.252Z" }
+wheels = [
+    { url = "https://files.pythonhosted.org/packages/94/b8/f1f62a5e3c0ad2ff1d189590bfa4c46b4f3b6e49cef6f26c6ee4e575394d/setuptools-80.10.2-py3-none-any.whl", hash = "sha256:95b30ddfb717250edb492926c92b5221f7ef3fbcc2b07579bcd4a27da21d0173", size = 1064234, upload-time = "2026-01-25T22:38:15.216Z" },
+]
+
 [[package]]
 name = "shiboken6"
 version = "6.11.2"
@@ -121,3 +444,35 @@ wheels = [
     { url = "https://files.pythonhosted.org/packages/ce/6b/fee1b4814317e4664e318644c9c007676c65a71e5b2b9d3ac4121a94dc0a/shiboken6-6.11.2-cp310-abi3-win_amd64.whl", hash = "sha256:6ab0eba1c904455df621f9a6df3ca2bb896bab8670572d2bc4e37804ae91f19a", size = 1226578, upload-time = "2026-08-18T06:37:18.002Z" },
     { url = "https://files.pythonhosted.org/packages/4d/b5/80c4e5aafeb8ac777cf5a1becfe87ac7197c35051df00b5f7819787e09d5/shiboken6-6.11.2-cp310-abi3-win_arm64.whl", hash = "sha256:97c49432488df958f0308736f3d15b6915d8826fc380af17bb4b9ec5c4a5e81b", size = 1784669, upload-time = "2026-08-18T06:37:21.046Z" },
 ]
+
+[[package]]
+name = "six"
+version = "1.17.0"
+source = { registry = "https://pypi.org/simple" }
+sdist = { url = "https://files.pythonhosted.org/packages/94/e7/b2c673351809dca68a0e064b6af791aa332cf192da575fd474ed7d6f16a2/six-1.17.0.tar.gz", hash = "sha256:ff70335d468e7eb6ec65b95b99d3a2836546063f63acc5171de367e834932a81", size = 34031, upload-time = "2024-12-04T17:35:28.174Z" }
+wheels = [
+    { url = "https://files.pythonhosted.org/packages/b7/ce/149a00dd41f10bc29e5921b496af8b574d8413afcd5e30dfa0ed46c2cc5e/six-1.17.0-py2.py3-none-any.whl", hash = "sha256:4721f391ed90541fddacab5acf947aa0d3dc7d27b2e1e8eda2be8970586c3274", size = 11050, upload-time = "2024-12-04T17:35:26.475Z" },
+]
+
+[[package]]
+name = "tibs"
+version = "0.5.7"
+source = { registry = "https://pypi.org/simple" }
+sdist = { url = "https://files.pythonhosted.org/packages/57/cd/6cf028decf1c2df4d26077dd5d0532587d93d4917233d5e004133166a940/tibs-0.5.7.tar.gz", hash = "sha256:173dfbecb2309edd9771f453580c88cf251e775613461566b23dbd756b3d54cb", size = 78255, upload-time = "2026-03-12T13:06:29.79Z" }
+wheels = [
+    { url = "https://files.pythonhosted.org/packages/12/2d/de2c579d3eea0f18212b5b16decb04568b7a0ef912d00581a77492609d4e/tibs-0.5.7-cp38-abi3-macosx_10_12_x86_64.whl", hash = "sha256:859f05315ffb307d3474c505d694f3a547f00730a024c982f5f60316a5505b3c", size = 411352, upload-time = "2026-03-12T13:06:52.016Z" },
+    { url = "https://files.pythonhosted.org/packages/74/71/4c21ccc5c2e1672f9cd91ed2c46604c250cffd9d386113772dded128b5cf/tibs-0.5.7-cp38-abi3-macosx_11_0_arm64.whl", hash = "sha256:a883ca13a922a66b2c1326a9c188123a574741a72510a4bf52fd6f97db191e44", size = 383971, upload-time = "2026-03-12T13:06:50.143Z" },
+    { url = "https://files.pythonhosted.org/packages/38/85/399940ac5393772792a209911a5efa42cf55cf621771e48b863211ac5a2a/tibs-0.5.7-cp38-abi3-manylinux_2_17_aarch64.manylinux2014_aarch64.whl", hash = "sha256:f70bd250769381c73110d6f24feaf8b6fcd44f680b3cb28a20ea06db3d04fb6f", size = 416256, upload-time = "2026-03-12T13:06:24.222Z" },
+    { url = "https://files.pythonhosted.org/packages/02/94/481a73e74d398949f57d297b1809a10a951d252e7ec94b6715ed952ce500/tibs-0.5.7-cp38-abi3-manylinux_2_17_armv7l.manylinux2014_armv7l.whl", hash = "sha256:76746f01b3db9dbd802f5e615f11f68df7a29ecef521b082dca53f3fa7d0084f", size = 428003, upload-time = "2026-03-12T13:06:23.064Z" },
+    { url = "https://files.pythonhosted.org/packages/9b/e0/72db1760a7f7fec1d5f3690e0855fbbccbcf0a4a2fd318c9d71f3b33f3a7/tibs-0.5.7-cp38-abi3-manylinux_2_17_ppc64le.manylinux2014_ppc64le.whl", hash = "sha256:847709c108800ad6a45efaf9a040628278956938a4897f7427a2587013dc3b98", size = 455589, upload-time = "2026-03-12T13:06:53.144Z" },
+    { url = "https://files.pythonhosted.org/packages/3e/26/9cd3395914bf705d6ae1e9a6c323f727e9dc88fef716327ce7f486e0b55a/tibs-0.5.7-cp38-abi3-manylinux_2_17_s390x.manylinux2014_s390x.whl", hash = "sha256:ad61df93b50f875b277ab736c5d37b6bce56f9abce489a22f4e02d9daa2966e3", size = 459266, upload-time = "2026-03-12T13:06:21.678Z" },
+    { url = "https://files.pythonhosted.org/packages/e9/3b/267f19a008d13c704dc0b044138a56239272a43531ccb05464129d0fbd01/tibs-0.5.7-cp38-abi3-manylinux_2_17_x86_64.manylinux2014_x86_64.whl", hash = "sha256:e13b9c7ff2604b0146772025e1ac6f85c8c625bf6ac73736ff671eaf357dda41", size = 423466, upload-time = "2026-03-12T13:06:41.212Z" },
+    { url = "https://files.pythonhosted.org/packages/e5/d4/424ae3515e0e013ad83186074bf3beb53399b9052c00da703415ccc316ca/tibs-0.5.7-cp38-abi3-manylinux_2_5_i686.manylinux1_i686.whl", hash = "sha256:0a7ce857ef05c59dc61abadc31c4b9b1e3c62f9e5fb29217988c308936aea71e", size = 452080, upload-time = "2026-03-12T13:06:32.112Z" },
+    { url = "https://files.pythonhosted.org/packages/b0/15/ab80beba83a134745439d33763e1d3b017f994abeb9c309a3ac9fd94e90e/tibs-0.5.7-cp38-abi3-musllinux_1_2_aarch64.whl", hash = "sha256:1d5521cc6768bfa6282a0c591ba06b079ab91b5c7d5696925ad2abac59779a54", size = 592311, upload-time = "2026-03-12T13:06:47.807Z" },
+    { url = "https://files.pythonhosted.org/packages/4c/21/f5cf41c15431e63aeaefb494e714d48d9e9061b4e01fcc01d1987e2e5faa/tibs-0.5.7-cp38-abi3-musllinux_1_2_armv7l.whl", hash = "sha256:477608f9b87e24a22ab6d50b81da04a5cb59bfa49598ff7ec5165035a18fb392", size = 703400, upload-time = "2026-03-12T13:06:16.968Z" },
+    { url = "https://files.pythonhosted.org/packages/4e/ec/b3bdb7dcc3de8513c5678a685f4e25bb85ef48526d7d535ddc592f9e8602/tibs-0.5.7-cp38-abi3-musllinux_1_2_i686.whl", hash = "sha256:ac0aa2aae38f7325c91c261ce1d18f769c4c7033c98d6ea3ea5534585cf16452", size = 664623, upload-time = "2026-03-12T13:06:48.894Z" },
+    { url = "https://files.pythonhosted.org/packages/a4/71/7b85af3ad1b2cd9871c8f50ba0eb17e54e12481b467678535e58aced0d98/tibs-0.5.7-cp38-abi3-musllinux_1_2_x86_64.whl", hash = "sha256:1b56583db148e5094d781c3d746815dbcbb6378c6f813c8ce291efd4ab21da8b", size = 635199, upload-time = "2026-03-12T13:06:34.798Z" },
+    { url = "https://files.pythonhosted.org/packages/b9/63/60220fb502beb857306afd4a5bac4a8617ae496f3b1f4968d127380fdefe/tibs-0.5.7-cp38-abi3-win32.whl", hash = "sha256:d4f3ff613d486650816bc5516760c0382a2cc0ca8aeddd8914d011bc3b81d9a2", size = 288454, upload-time = "2026-03-12T13:06:30.978Z" },
+    { url = "https://files.pythonhosted.org/packages/46/ab/aab78827ba7e0d65fe346b86d1d61e0792c38d5f9b7547e0f71b7027c835/tibs-0.5.7-cp38-abi3-win_amd64.whl", hash = "sha256:a61d36155f8ab8642e1b6744e13822f72050fc7ec4f86ec6965295afa04949e2", size = 304135, upload-time = "2026-03-12T13:06:35.884Z" },
+    { url = "https://files.pythonhosted.org/packages/48/59/e9e6a610928a4bcbf04f0ac1436ee320aa8cbe95181f1aa32687c50e858b/tibs-0.5.7-cp38-abi3-win_arm64.whl", hash = "sha256:130bc68ff500fc8185677df7a97350b5d5339e6ba7e325bc3031337f6424ede7", size = 289272, upload-time = "2026-03-12T13:06:19.247Z" },
+]